Electrical and Computer Engineering Commons^™

Talif Quantification Of Nitrogen Atoms Applied To Experimental Simulation Of Titan’S Atmosphere, Et. Es-Sebbar, Y. Benilan, E. Arzoumanian, M.-C. Gazeau

Dr. Et-touhami Es-sebbar

No abstract provided.

S.E.T.U.P., A New Program Of Representative Simulations Of Titan’S Atmosphere: Current Status, M-C. Gazeau, E. Arzoumanian, Y. Benilan, Et. Es-Sebbar, A. Jolly, S. Perrier, C. Romanzin

Dr. Et-touhami Es-sebbar

No abstract provided.

Comparison Of Townsend Dielectric Barrier Discharge In N2, N2/O2 And N2/N2o: Behavior And Density Of Radicals, F. Massines, Et. Es-Sebbar, N. Gherardi, N. Naudé, D. Tsyganov, P. Ségur, S. Pancheshnyi

Dr. Et-touhami Es-sebbar

No abstract provided.

Dual Beam Actuation Of Piezoelectric Aln Rf Mems Switches Integrated With Aln Contour-Mode Resonators, Nipun Sinha, Rashed Mahamameed, Chengjie Zuo, Marcelo B. Pisani, Carlos R. Perez, Gianluca Piazza

Nipun Sinha

This work reports on piezoelectric Aluminum Nitride (AlN) based dual-beam RF MEMS switches that have been monolithically integrated with AlN contour-mode resonators. The dual-beam switch design presented in this paper intrinsically compensates for the residual stress in the deposited films, requires low actuation voltage (5-20 V), facilitates active pull-off to open the switch and fast switching times (1 to 2 µsec). This work also presents the combined response (cascaded S-parameters) of a resonator and a switch that were co-fabricated on the same substrate. The response shows that the resonator can be effectively turned on and off by the switch. A …

Dual Beam Actuation Of Piezoelectric Aln Rf Mems Switches Integrated With Aln Contour-Mode Resonators, Nipun Sinha, Rashed Mahamameed, Chengjie Zuo, Marcelo B. Pisani, Carlos R. Perez, Gianluca Piazza

Marcelo B Pisani

This work reports on piezoelectric Aluminum Nitride (AlN) based dual-beam RF MEMS switches that have been monolithically integrated with AlN contour-mode resonators. The dual-beam switch design presented in this paper intrinsically compensates for the residual stress in the deposited films, requires low actuation voltage (5-20 V), facilitates active pull-off to open the switch and fast switching times (1 to 2 µsec). This work also presents the combined response (cascaded S-parameters) of a resonator and a switch that were co-fabricated on the same substrate. The response shows that the resonator can be effectively turned on and off by the switch. A …

Criteria On Utility Designing Of Convex Optimization In Fdma Networks, Zheng Sun, Wenjun Xu, Zhiqiang He, Kai Niu

Zheng Sun

In this paper, we investigate the network utility maximization problem in FDMA systems. We summarize with a suite of criteria on designing utility functions so as to achieve the global optimization convex. After proposing the general form of the utility functions, we present examples of commonly used utility function forms that are consistent with the criteria proposed in this paper, which include the well-known proportional fairness function and the sigmoidal-like functions. In the second part of this paper, we use numerical results to demonstrate a case study based on the criteria mentioned above, which deals with the subcarrier scheduling problem …

Proceedings From Scientific Conference On Green Energy And It, Dr. Erik Dahlquist

Dr. Erik Dahlquist

This conference is part of the annual Energitinget, a national arena for energy in Sweden, with some 2500 participants. The focus with this session is to give a forum for researchers to present scientific results, and also to discuss these with other researchers. It contains papers in the area of Energy and IT as well as Green energy generally

Laboratory Experiments As Support To The Built Up Of Titan’S Theoretical Models And Interpretation Of Cassini-Huygens Data, M-C. Gazeau, Y Benilan, Et. Es-Sebbar, T. Ferradaz, E. Hébrard, A. Jolly, F. Raulin, C. Romanzin, J-C. Guillemin, C. Berteloite, A. Canosa, S. D. Le Picard, Ian R. Sims

Dr. Et-touhami Es-sebbar

No abstract provided.

Use Of Modeling And Simulation In Pulp And, Dr. Erik Dahlquist

Dr. Erik Dahlquist

The book is a handbook for operators and process engineers in primarily pulp and paper industry, but also other process industries about how to utilise simulation as a tool for enhanced process operations. The book has been written as part of a EU COST action on Process Simulation, with 14 countries and 50 researchers and process industry representatives involved.

Implementation Of A Mems Laboratory Course With Modular, Multidisciplinary Team Projects, John Lee, Stacy H. Gleixner, Tai-Ran Hsu, David W. Parent

David W. Parent

This paper presents the implementation and outcomes of a hands-on laboratory course in microelectromechanical systems (MEMS), co-developed by a multidisciplinary team of faculty from mechanical engineering, electrical engineering, and materials engineering. Central to the design of the course is an emphasis on implementing modules that are able to overcome critical barriers related to (1) diverse academic background from different majors and (2) practical limitations in microfabrication facilities. These points are vital for promoting MEMS education, because they expand the student pool and reach audiences that need a cost-effective way to support instructional laboratory experiences in MEMS without the broader infrastructure …

Derivation And Application Of A Conserved Orbital Energy For The Inverted Pendulum Bipedal Walking Model, Jerry E. Pratt, Sergey V. Drakunov

Sergey V. Drakunov

A Development Framework For Hands-On Laboratory Modules In Microelectromechanical Systems (Mems), John Lee, Stacy H. Gleixner, Tai-Ran Hsu, David W. Parent

David W. Parent

This paper presents work-in-progress in terms of a framework that we have structured to support effective joint development among faculty from different engineering backgrounds, spanning mechanical engineering (ME), electrical engineering (EE), and materials engineering (MatE). The framework is organized in short instructional modules designed to span not only major device types and different fabrication technologies, but also different levels of resource requirements. An example of using functional prerequisites--rather than course prerequisites—is presented for one module, wherein each functional prerequisite must be satisfied by at least one member of each student team that will undertake the module. Roles of the faculty …