Open Access. Powered by Scholars. Published by Universities.®

Electrical and Computer Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

1997

Articles 1 - 25 of 25

Full-Text Articles in Electrical and Computer Engineering

Study On The Oxygen Electrodes Of Alkaline Fuel Cells Effect Of Dopant On The Activity Of Ag/C Catalyst, Jiawei Teng Nov 1997

Study On The Oxygen Electrodes Of Alkaline Fuel Cells Effect Of Dopant On The Activity Of Ag/C Catalyst, Jiawei Teng

Journal of Electrochemistry

A new kind of nonnoble catalyst for the oxygen electrodes of Alkaline Fuel Cells was investigated. The AgNiBiHg/C catalyst, which was prepared by chemical reduction, was active for the cathodic reduction of oxygen in alkaline fuel cells. It was found that the catalytic activity was improved by adding Ni, Bi, Hg to Ag/C catalyst, and the maximum activity was observed at Ag50%Ni2%Bi3%Hg3%C42%(wt%). XRD inconjunction with SEM indicated that the crystalline silver turned into amorphous in the presence of doping agents and the grain size of silver was reduced. No dramatic deactivation of the catalyst occured after 5200 hours of service.

Go to article

The Activity Of Alloy CuNi Electrode In Electroreduction Of Aromatic NitroCompounds, Chunan Ma, Shaoping Tong, Xiaojun Cheng, Hui Wang Nov 1997

The Activity Of Alloy CuNi Electrode In Electroreduction Of Aromatic NitroCompounds, Chunan Ma, Shaoping Tong, Xiaojun Cheng, Hui Wang

Journal of Electrochemistry

CuNi alloy on the basis of copper at different ratio Cu/Ni are prepared by codepostion. The cathode activtiy of film are studied by steadystate polarization for electroreduction nitrobenzene (NB) and 1,5dinitroanthraquinone (1,5DNA) to paminophenol and 1,5diamino4,8dihydroanthraquinone respectly. The results show that the alloy cathodes at different ratio Cu/Ni have different exchange current density (io) and apparent activition energy (EA). The alloy (CN30) has maximal io  and minimal EA by codeposition at the following conditions: electrolyte: 0.05 mol/L CuSO4·5H2O+0.6 mol/L NiSO4·6H2O+0.25 mol/L Na3Cit·2H2O; current density: 0.6 A/dm2 , pH=6, temperature at 50 ℃. Compared with the common cathodes such as …

Go to article

Photoluminescence Of Photoelectrochemically Etched N+-Si, Guozheng Li, Chengqian Zhang, Xiumei Yang Nov 1997

Photoluminescence Of Photoelectrochemically Etched N+-Si, Guozheng Li, Chengqian Zhang, Xiumei Yang

Journal of Electrochemistry

PS layer on n+Si with (111) orientation prepered by means of photoelectrochemically etched has photoluminescent (PL) ability like PS layer on usual nSi. The data of PL spectra and quenching are given.

Go to article

Preparation Of High Rate Discharge Foamed Nicd Battery, Yuming Wang Nov 1997

Preparation Of High Rate Discharge Foamed Nicd Battery, Yuming Wang

Journal of Electrochemistry

A novel device of SC type foamed NiCd battery is presented, in which, the innerresistance of battery is appeared to be reduced, and the electrode performance is gained to very improved, and so, this battery can be suited to using of the powerdrive pistol drill.

Go to article

Molten Carbonate Fuel Cell Materials And Technology, Naichao Li, Baolian Yi Nov 1997

Molten Carbonate Fuel Cell Materials And Technology, Naichao Li, Baolian Yi

Journal of Electrochemistry

Molten Carbonate Fuel Cell materials are reviewed, and the technology of Molten Carbonate Fuel Cell are discussed.

Go to article

Study On Perchlorate Produced By Electrolysis With Oxygen Cathode, Zhigang Shao, Baolian Yi, Naichao Li, Ming Han Nov 1997

Study On Perchlorate Produced By Electrolysis With Oxygen Cathode, Zhigang Shao, Baolian Yi, Naichao Li, Ming Han

Journal of Electrochemistry

A new method of measuring the flow capacity of cell gas in the perchlorate cell process equipped with an oxygen cathode is applided to investigate the influence of changes in the concentration of solution (chloride, chlorate, perchlorate and metal ion) and changes in the operation parameters (current density, temperature and pH) on perchlorate current efficiency. The main abstacle that the oxygen cathode is used in the perchlorate cell process is put forward and a method is provided to resolve it.

Go to article

Investigation On Electro Reduction Behaviour Of Copper Anodic Products In Concentrated Naoh Solutions Ⅱ. Electro Reduction Of Cu(Ⅱ) Products, Jianbo He, Hanhe Chen, Jianxin Lin Aug 1997

Investigation On Electro Reduction Behaviour Of Copper Anodic Products In Concentrated Naoh Solutions Ⅱ. Electro Reduction Of Cu(Ⅱ) Products, Jianbo He, Hanhe Chen, Jianxin Lin

Journal of Electrochemistry

Potentiostatic oxidation potentiodynamic or galvanostatic reduction methods have been used to study the cathodic reduction behaviour of various products anodically formed on the second stage of copper oxidation in concentrated NaOH solutions. Seven cathodic current peaks and the corresponding cathodic potential plateaus are observed on the potentiodynamic E/i curves and the galvanostatic E/t curves, respectively. In the negative potential scan, there are three couples of voltammetric peaks which have been attributed to the formation and reduction of CuO, Cu(OH) 2 and Cu(Ⅱ) ion, respectively. The complicated mechanism for the electro formation of the three Cu(Ⅱ) species are discussed.

Go to article

Surface Modifications Of Carbon Materials Used As Anode Of Lithium Ion Battery Ⅲ. Improvement Of Artificially Imposed Solid Electrolyte Film On Cell Performance, Shuhua Ma, Xiabin Jing, Fosong Wang Aug 1997

Surface Modifications Of Carbon Materials Used As Anode Of Lithium Ion Battery Ⅲ. Improvement Of Artificially Imposed Solid Electrolyte Film On Cell Performance, Shuhua Ma, Xiabin Jing, Fosong Wang

Journal of Electrochemistry

The improving effect of solid electrolyte film artificially imposed on carbon electrode was investigated. The result showed that both the charge/discharge capacity and first charge/discharge efficiency, to a certain extent, were enhanced, and the result also suggested the effectiveness of the substitution of the artificially imposed solid electrolyte film for the inherent passivating film which was formed on the surface of the carbon electrode while inserted in the electrolyte during charging or discharging. The Scanning Electron Microscope result displayed the compact and well defined morphology of the artificially imposed crystalline film.

Go to article

Studies On The Failure Modes Of Stationary Vrla Batteries, Yibo Tong, Xiangming Qiu Aug 1997

Studies On The Failure Modes Of Stationary Vrla Batteries, Yibo Tong, Xiangming Qiu

Journal of Electrochemistry

In order to improve the reliability and the quality of stationary valve regulated lead acid (VRLA) batteries, the failure modes of the stationary VRLA batteries which caused by the water loss and the thermal runaway are studied. The water loss may be solved by increasing the Oxygen recombination efficiency, choosing the suitable grid material and the additives of megative paste, decreasing the corrosion of the positive plates. The thermal runaway may be solved by decreasing the inner ohmic resistance of VRLA batteries, improving the outside condition of batteries such as putting into the absorbing heat material between the abtteries etc..

Go to article

Electrocatalytic Oxidation Of Methanol On The Stearate Nickel L B Film, Benzeng Hua, Wenyan Hu, Yanzhen Chen Aug 1997

Electrocatalytic Oxidation Of Methanol On The Stearate Nickel L B Film, Benzeng Hua, Wenyan Hu, Yanzhen Chen

Journal of Electrochemistry

The stearate nickel L B films is good electroacatlyst for the oxidation of methanol MeOH in alkaline. The electrochemical behaviors of stearate nickel L B films is affected by the concentration of KOH. The rate of quantity of mickel ion and stearic acid in L B films is 1∶1, which means that the nickel ion may exist in -COONi(OH) form. The electrocatalytic process is influenced by the concentration of OH - , it involves the penetration of MeOH into the films. The oxidative currents of MeOH are linearly dependent on the bulk concentration.

Go to article

Preparation And Examination Of Planar Type Solid Oxide Fuel Cells, Yi Jiang, Jingwang Yan, Shizhong Wang, Chunying Yu, Wenzhao Li Aug 1997

Preparation And Examination Of Planar Type Solid Oxide Fuel Cells, Yi Jiang, Jingwang Yan, Shizhong Wang, Chunying Yu, Wenzhao Li

Journal of Electrochemistry

The solid oxide fuel cells of planar type(SOFC) have been developed after successfully preparing La 0.8 Sr 0.2 MnO 3 cathodes and Ni YSZ ceramic anodes on YSZ plates and solving the high temperature sealing technical problem. Examination of the single cells fabricated showed that the maximum power output at 950 ℃ for H 2 as fuel and air as oxidant reached 0.12 W/cm 2. It was found that the large polarization overpotential of the Ni YSZ anode and the Ohmic losses of the cells were two main factors responsible for the relative low output power density.

Go to article

Gallium Desorption Behavior At Algaas/Gaas Heterointerfaces During High-Temperature Molecular Beam Epitaxy, K. Mahalingam, D. L. Dorsey, K. R. Evans, Rama Venkat Aug 1997

Gallium Desorption Behavior At Algaas/Gaas Heterointerfaces During High-Temperature Molecular Beam Epitaxy, K. Mahalingam, D. L. Dorsey, K. R. Evans, Rama Venkat

Electrical & Computer Engineering Faculty Research

A Monte Carlo simulation study is performed to investigate the Ga desorption behavior during AlGaAs-on-GaAs heterointerface formation by molecular beam epitaxy. The transients in the Ga desorption rate upon opening the Al shutter are shown to be associated with the concurrent reduction in the V/III flux ratio. Monte Carlo simulations employing a constant V/III flux ratio yield a “steplike” variation in the Ga desorption rate with the resulting interfaces closer in abruptness to the ideal AlGaAs-on-GaAs interface. Further details on the stoichiometry of the interface and its relationship with predicted Ga desorption profiles is presented.

Go to article

Polymer Electrolyte Fuel Cell Powered Vehicles, Naichao Li, Baolian Yi May 1997

Polymer Electrolyte Fuel Cell Powered Vehicles, Naichao Li, Baolian Yi

Journal of Electrochemistry

The background, status and commercialization prospect of polymer electrolyte fuel cell vehicles are surveyed in this paper. The technology of this cell and system used in vehicles is discussed.

Go to article

Electroluminescence Of Photoelectrochemically Etched N + Si, Guozheng Li, Chengqian Zhang, Xiumei Yang May 1997

Electroluminescence Of Photoelectrochemically Etched N + Si, Guozheng Li, Chengqian Zhang, Xiumei Yang

Journal of Electrochemistry

Porous silicon with micrometer size pores, which is made on n + Si by photoelectrochemically etched, has electroluminescent property. Each monochromic intensity and wavelength range of luminescent spectra depend on polarized potential. The intersity and the stability of cathodic electroluminescence is high than those of anodic one. Voltammetric behavior before quenching indicated that the electrochemical reactions of some surface species are involved in except the reduction of S 2O 2- 8, which leads to radiative recombination. The energy band diagram based on n + Si (E g=1.1 eV)/PS(E g=1.8 eV) junction is proposed.

Go to article

Studies Of Electrocatalytic Properties Of Electrode Of Dispersed Pt On Gc Support In Ethylene Glycol Oxidation, Shengpei Chen, Shigang Lu Guoqiang Sun, Zhiyou Zhou, Shuanjing Hong May 1997

Studies Of Electrocatalytic Properties Of Electrode Of Dispersed Pt On Gc Support In Ethylene Glycol Oxidation, Shengpei Chen, Shigang Lu Guoqiang Sun, Zhiyou Zhou, Shuanjing Hong

Journal of Electrochemistry

The structures and properties of electrocatalyst of dispersed Plutinum(Pt) on glassy carbon(GC) support under different conditions were studied using cyclic voltammetry,potential step technique,x ray diffraction(XRD) and scanning Electron microscopy(SEM). The results indicated that after having been treated in high temperature,the dispersed Pt on GC support was recrystallised with preferented orientation,and the grain of Pt microcrystal become large and regular.It was illustrated that the dispersed Pt on GC support after high temperature treatment exhibited better stability and high activity for ethylene glycol oxidation.

Go to article

Electrochemical Behavior Of Superoxide Dismutase On Gold Minigrid With Thin Layer Cell, Xiaqin Wu, Qian Liu, Bin Xu, Xiaoyun Men, Zongrang Zhang May 1997

Electrochemical Behavior Of Superoxide Dismutase On Gold Minigrid With Thin Layer Cell, Xiaqin Wu, Qian Liu, Bin Xu, Xiaoyun Men, Zongrang Zhang

Journal of Electrochemistry

The electrochemical behavior of superoxide dismutase (Cu, Zn SOD) was investigated on gold wire electrode and gold minigrid with thin layer cell by cyclic voltammetry. A quasi reversible redox wave of SOD has obtained on gold minigrid thin layer electrode, but only oxidation peak has observed on gold wire electrode. The electrochemical reaction parameters, such as the formal potential E 0 ′, diffusion coefficient D and standard rate constant k 0′ were estimated.

Go to article

Surface Modification Of Molten Carbonate Fuel Cell Anode, Baizeng Fang, Xinyu Liu, Xindong Wang, Shuzhen Duan May 1997

Surface Modification Of Molten Carbonate Fuel Cell Anode, Baizeng Fang, Xinyu Liu, Xindong Wang, Shuzhen Duan

Journal of Electrochemistry

In this study, the anode material of molten carbonate fuel cell was modified by the deposition of niobium on nickel surface. The results of polarization experiments reveal that the corrosion resistant properties as well as electrocatalytic activity have been improved greatly.

Go to article

Electrochemical Synthesis And Characterization Of Ba Pb O And Bi Pb O Oxides, Min Zhao Liangzhong Xie, Cuiying Xu, Jinbiao Zhang Feb 1997

Electrochemical Synthesis And Characterization Of Ba Pb O And Bi Pb O Oxides, Min Zhao Liangzhong Xie, Cuiying Xu, Jinbiao Zhang

Journal of Electrochemistry

Pb based oxides Ba Pb O and Bi Pb O were synthesized from aqueous solutions by using electrochemical method. The resulting Ba Pb O and Bi Pb O were characterized using XPS, EDX and XRD. The results show that perovskite BaPb 0.9 O 3 can be electrodeposited on the anode only from strong alkaline solution. In acid aqueous solution, conducting BiPb 2O z oxide is fromed on the anode. In these oxides the nominal valence of lead is +4.

Go to article

Problems Of The Study Of Anodic Films On Pb In Sulfuric Acid Solution(Ⅲ), Houtian Liu, Qunzhou Wang, Weifang Zhou Feb 1997

Problems Of The Study Of Anodic Films On Pb In Sulfuric Acid Solution(Ⅲ), Houtian Liu, Qunzhou Wang, Weifang Zhou

Journal of Electrochemistry

The interstitial liquid among the particles in anodic Pb(Ⅱ) films could be the major passage for ion transportation. This is discussed with the mechanism of the cathodic reduction of anodic PbSO 4 film and the effect of Sb on the growth of anodic Pb(Ⅱ) oxides film.

Go to article

Electrochemical Studies Of Spinel Limn 2o 4 Rechargeable Lithium Battery, Li Feng, Yuqin Wu Lie Chang, Hong Li, Yibin San, Tianhong Lu Feb 1997

Electrochemical Studies Of Spinel Limn 2o 4 Rechargeable Lithium Battery, Li Feng, Yuqin Wu Lie Chang, Hong Li, Yibin San, Tianhong Lu

Journal of Electrochemistry

The spinel Li intercalation compound LiMn 2O 4 was prepared and studied using ac impedance and cyclic voltammogram techniques. It was first discussed that the impedance behaviors of LiMn 2O 4 electrode varied as lithium ion was intercalated in or out the electrode with the help of fractal theory. The Li reversible behaviors in LiMn 2O 4 electrode were shown by the cyclic voltammogram results.

Go to article

Surface Modifications Of Carbon Materials Used As Anode Of Lithium Ion Batteryⅱ.The Carbon Material With Core Shell Structure And Its Positive Effect On Cell Performance Of Graphite Anode, Shuhua Ma, Hanju Guo, Ji Li, Hongze Liang, Xiabin Jing, Fosong Wang Feb 1997

Surface Modifications Of Carbon Materials Used As Anode Of Lithium Ion Batteryⅱ.The Carbon Material With Core Shell Structure And Its Positive Effect On Cell Performance Of Graphite Anode, Shuhua Ma, Hanju Guo, Ji Li, Hongze Liang, Xiabin Jing, Fosong Wang

Journal of Electrochemistry

The carbon powders and film electrode with core shell structure were prepared by carbonization in gas state with using refined coal as shell material and Artificial Graphite and Mesocarbon Microbeads (2 800 ℃) graphite as core material. Galvanostatic charge/discharge measurement showed that both steady charge/discharge capacity and first charge/discharge efficiency were improved. Cyclic voltammetry indicated that the peak at about 0.7 V vs. Li +/Li characteristic of decomposition of electrolyte got weakened, and a more compact film was formed. X ray diffraction measurement suggested the existence of amorphous carbon shell on the carbon powders and carbon film.

Go to article

Studies On An Iron Heteropolyacid Redox Flow Battery, Peiju Gu Yuanpeng Sun, Wansheng You, Zhorgyin Tan Feb 1997

Studies On An Iron Heteropolyacid Redox Flow Battery, Peiju Gu Yuanpeng Sun, Wansheng You, Zhorgyin Tan

Journal of Electrochemistry

This paper reports a new Fe HP redox flow cell. The positive and negative electrodes active materials are phosphomolybdic acid and acidified ferrous sulphate solutions respectively. Two activated porous carbon felt electrodes where the electrochemical reactions take place, are separated by a selective cation exchange membrane. The both couples have a suitable electrochemical reversibility on carbon and graphite electrodes. The active materials of the cell have very high stability. Moreover the cell has no life cycle limiting.

Go to article

Theory Of Thin-Skin Eddy-Current Interaction With Surface Cracks, Nicola Harfield, John R. Bowler Jan 1997

Theory Of Thin-Skin Eddy-Current Interaction With Surface Cracks, Nicola Harfield, John R. Bowler

Nicola Bowler

Eddy-current non-destructive evaluation is commonly performed at relatively high frequencies at which the skin depths are significantly smaller than the dimensions of a typical crack. A thin-skin analysis of eddy currents is presented in which the electromagnetic fields on the crack faces are described in terms of a potential which obeys a two-dimensional Laplace equation. Solutions of this equation for defects in both magnetic and non-magnetic materials are determined by applying thin-skin boundary conditions at the crack perimeter. The impedance change of an eddy-current coil due to the defect is then calculated by numerical evaluation of one-dimensional integrals over the …

Go to article

Optical And Electrical Properties Of Cualse² Thin Films Obtained By Selenization Of Cu/Al/Cu... Al/Cu Layers Sequentially Deposited, J. C. Bernède, S. Marsillac, C. El Moctar, A. Conan Jan 1997

Optical And Electrical Properties Of Cualse² Thin Films Obtained By Selenization Of Cu/Al/Cu... Al/Cu Layers Sequentially Deposited, J. C. Bernède, S. Marsillac, C. El Moctar, A. Conan

Electrical & Computer Engineering Faculty Publications

Optical and electrical properties of CuAlSe2 thin films obtained by selenization of Cu/Al/Cu...Al/Cu layers sequentially deposited have been investigated. It is shown that the expected energy gap (2.67 eV) is measured for well crystallized films, whereas a slightly higher value is measured for films not so well crystallized. Raman diffusion also shows differences between well and poorly crystallized films with peaks corresponding to the reference powder for the former samples. A p-type conductivity is found whatever the crystalline quality of the samples. The conductivity of the films depends also strongly on their crystalline properties. When the films are badly …

Go to article

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali Jan 1997

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali

Electrical & Computer Engineering Faculty Publications

CuAlSe2 thin films have been synthesized by chalcogenization of thin Cu and Al layers sequentially deposited by evaporation under vacuum. It is shown that CuAlSe2 films are obtained with some Cu2-δSe and Se phases present at the surface. These surface phases are suppressed by annealing under vacuum and by chemical etching in a KCN solution. At the end of the process, the XRD spectrum demonstrates that textured CuAlSe2 films have been obtained with preferential orientation of the crystallites along the (112) direction. The gap of the films is 2.7 eV as expected. The …

Go to article