Hydraulic Engineering Commons^™

Accumulation Of Lead By Biofilms In Drinking Water Distribution Systems, Kaleb Oren Belcher

Graduate Theses and Dissertations

Recent crises, such as the one in Flint, MI, indicate that lead exposure from drinking water is a major health concern in the United States. Over six million lead service lines are still in use in the United States, and a universal protocol to safely remove these lead service lines from drinking water distribution systems has not yet been established. This paper calls to attention the potential hazard that biofilms pose as a source of lead in distribution systems, even after the removal of lead pipes. This study used a simulated water distribution system containing a lead source pipe and …

Testing And Development Of Pre-Stressed Cfrp Retrofit Strategies For Controlling Fatigue Cracking In Steel Waterway Lock Gate Structures, Maggie Langston

Graduate Theses and Dissertations

Steel waterway lock gates across the national inland waterway transportation network are reaching and exceeding their intended service life, often experiencing component failures that lead to service interruptions. Unscheduled maintenance and repair of lock gates can be expensive and cause economic ripples throughout the entire inland waterway network. These lock gate component failures are often caused by fatigue cracking from repeated loading during operation. This thesis develops and tests a prestressed carbon fiber reinforced polymer (CFRP) fatigue retrofit for controlling fatigue demands within lock gate components. The study expands upon a recent analytical work by Lozano (2017) by experimentally investigating …

Evaluation Of Water Resources And Hydraulic Influences In The Restoration Of The Western Part Of The Mesopotamian Marshlands, Ali Kareem Al-Quraishi

Graduate Theses and Dissertations

The purpose of this study is to assess the water resources and water conveyance system of the western part of the Mesopotamian marshes (Al-Hammar marsh) as well as develop a water conveyance system to distribute water throughout the western Al-Hammar marsh. These processes are significant to identify the current restoration problems and help to create restoration strategies for the marsh. Also, proper management strategy to the Al-Hammar marsh is necessary to preserve the marsh ecosystem, irrigate lands, and provide domestic necessities in the villages.

The overall project is divided into three main chapters which address the current ecological and hydrological …

Evaluation Of The Equations Used To Calculate Hydraulic Conductivity Values From Two-Stage Borehole Tests, Johnathon Dale Blanchard

Civil Engineering Undergraduate Honors Theses

A compacted clay liner (CCL) test pad was constructed for the purpose of evaluating the testing procedures utilized for determining hydraulic conductivity of a CCL. These procedures include ASTM D6391 (2014) Method C and ASTM D6391 Method A. Method C was recently added to ASTM D6391(2014) and was evaluated based upon comparison of results obtained from previous research with results from the data presented herein. The test pad was instrumented with volumetric water content probes and water matric potential sensors to monitor the wetting front in the soil. The data obtained from this instrumentation should be used to develop a …

Dynamic Testing Of An Elevated Water Tank, Alexander Michael Font

Graduate Theses and Dissertations

The objective of this thesis was to identify the modal properties of a pedesphere type, elevated water tank under different operating conditions relating to the water level in the tank. The research that was conducted included both numerical and experimental components. The numerical components consisted of a simple hand calculation to identify the fundamental frequency as well as numerical computer models to identify the natural frequencies and mode shapes for the first three bending modes. The experimental components consisted of characterizing the vibration of the elevated water tank in its current environment through ambient vibration testing.

Examination Of Nitrogen To Phosphorus Ratio In Nutrient Removal From Wastewater Through Chlorella Vulgaris, Courtney L. Hill

Civil Engineering Undergraduate Honors Theses

A need for phosphorus removal is becoming increasingly evident as some wastewater treatment plants struggle to meet wastewater effluent nutrient requirements. High nutrient levels in wastewater effluents have also caused ongoing tension between the state of Oklahoma and Arkansas regarding the pollution of the Illinois River. This research seeks to establish the relationship between nitrogen to phosphorus ratio in wastewater and the level of nutrient reduction using Chlorella vulgaris. Seed cultures of Chlorella vulgaris were added into solutions with various ratios of nitrate to phosphate representative of treated domestic wastewater and the removal of nitrogen and phosphorus were measured in …

Hydraulic Conductivity Of Environmentally Controlled Landfill Liner Test Pad, Camila Maldonado Soria Galvarro

Civil Engineering Undergraduate Honors Theses

Laboratory and field hydraulic conductivity tests have been conducted on soil samples to develop and verify the zone of acceptance for liner placement. Compaction testing and flexible wall hydraulic conductivity tests were performed on fifteen (15) samples to determine the dry unit weight, molding water content, and laboratory permeability. Five of the fifteen samples were compacted at Standard proctor energy, five were compacted at 75 percent of Standard proctor energy, and five were compacted at 50 percent of Standard proctor energy. The results obtained from the laboratory portion of the testing program (the zone of acceptance) are presented. A ten …

Effects Of Piston Uplift, Piston Friction, And Machine Deflection In Reduced Triaxial Extension Testing, Morgan Race

Civil Engineering Undergraduate Honors Theses

A series of Reduced Triaxial Extension (RTE) tests were conducted on dummy (brass) and null (water) samples to determine the effects of (corrections required for) piston uplift, piston friction and system compliance associated with RTE tests. During the consolidation stage of RTE tests, the sample may be consolidated in isotropic or anisotropic stress conditions. During the shearing stage of an RTE test, the sample is unloaded in the axial direction by decreasing the deviator stress while the radial stress remains constant. Ten (10) tests were conducted on a brass "dummy" sample. The device was assembled in the same manner as …