Construction Engineering and Management Commons^™

Truss Bridge Damage Localization And Severity Estimation Using Influence Lines, Hamoud Alshallaqi

Civil and Environmental Engineering Theses and Dissertations

The safety of bridges is one of the primary concerns of researchers, engineers, and bridge owners and managers, especially when bridges are approaching the end of their intended service lives. The estimation of bridge condition and remaining service life is critical to prioritize the allocation of available funding for repairs and rehabilitation. Various methods, including both dynamic and static approaches, have been developed to detect and localize bridge damage and estimate its severity. This research presents a methodology for detecting a single damaged member in a truss bridge and estimating the severity of the damage using static vertical deflection influence …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Improve The Prediction Of Camber, Deflection, And Prestress Losses In Precast, Prestressed Concrete Bridge Girders, Ahmed Ali Hussein Al Mohammedi

Graduate Theses and Dissertations

Many precast, prestressed concrete girders have camber less or higher than the design values. This discrepancy between the design and the actual camber creates construction problems when installing the cast-in-place concrete deck. The objective of this research was to improve the accuracy of estimating long-term camber, deflection, and prestress losses of precast, prestressed concrete girders.

The experimental program consisted of measuring concrete properties and performing field measurements of camber, deflection, and prestress losses for girders in Arkansas. The investigation involved testing nine full-scale girders from two prestressed concrete plants that regularly supply concrete girders to bridge projects in Arkansas. The …

Gaylord Produce Removal Machine, Marcus Takashi Hirose Lee, Jacob Michael Perlman, Carissa Abigail Kamm, Mark Misao Loera

Mechanical Engineering

This Final Design Review Report outlines the senior design project that began Winter Quarter of 2021 at California Polytechnic State University. Our team consists of three mechanical engineers and a general engineer, working together to design, build, and test a product for Alameda County Food Bank. The goal of the final product is to relieve volunteers and employees of tedious manual labor and increase efficiency during the removal of produce from large Gaylord containers. This document describes background research, the objectives of the project, chosen concept design, analysis and initial prototyping of said concept, the final design, and verification prototype …

Development Of An Ultra-High Performance Concrete Joint Detail For Short-Span Bridges, Francisco De Jesus Chitty Gozalo

FIU Electronic Theses and Dissertations

Slab beam superstructures have been used for short-span bridges since prestressed concrete began to be used in the US. Poor joint performance of these superstructures led to recent revisions to design standards; one example being the Florida Slab Beam (FSB). The FSB and other similar slab beam systems include a composite cast-in-place (CIP) reinforced concrete deck and joint between adjacent beams. An optimized joint design has been developed to accelerate the construction times and eliminate the need for a CIP deck by using ultra-high performance concrete (UHPC) in the longitudinal closure pour to connect the precast members.

The optimized joint …

Assessment Of Key Imperatives For Enhancing Precast Adoptability In Egypt, Mostafa Sameh

Theses and Dissertations

Precast Concrete’s modular application concept is a major construction method that has been used historically seen in various shapes, forms, and with a wide range of constituents. Examples include Ancient Egypt and China among several impressive structures in old civilizations. The major advantages of precast concrete lie in its adaptability, resilience, and versatility which makes precast concrete one of the most agile building materials. Precast concrete as we know it today has been introduced to our markets over the past several decades. Having similar advantages to that of old precast building methods, the road has been paved for wider use …

An Improved Earned Value Management Method Integrating Quality And Safety, Brian Briggs

LSU Doctoral Dissertations

The construction industry invests significant time and money to improve quality and safety while reducing cost and schedule impacts. The industry has a sincere desire to improve construction project management methods to improve efficiency. Historically, quality and safety underperformances result from undermanaged quality control and safety activities. The cost and schedule impacts associated with poor quality work have always had an impact on construction operations. The unprecedented challenges and uncertainties of COVID-19 highlighted the need to improve the Earned Value Management (EVM) method within construction to reflect these quality and safety activities. The central goal of this dissertation is to …

Mitigating Calcium Oxychloride Damage In Cementitious Paste And Concrete Utilizing Supplementary Cementitious Materials, Casey Jones

Graduate Theses and Dissertations

It is understood among engineers in the United States (U.S.) that improvement is needed throughout the transportation infrastructure. In the 2021 Infrastructure Report Card produced by the American Society of Civil Engineers, the roadways of this nation merit a D. This leaves room for improvement in order to provide durable pavements throughout this nation. Areas with significant winter weather may have exacerbated effects in decreased roadway longevity due to freezing/thawing cycles and the use of chemical deicers to mitigate gelid roadway conditions. Much research focuses on surface scaling and reinforcement corrosion using these materials; however, joint deterioration, due to chemical …

Applications Of Masw And Mhvsr Techniques For Infrastructure Evaluation With A Focus On The Effects Of Different Transformation Techniques And Near-Field Effects On Derived Dispersion Data, Salman Rahimi

Graduate Theses and Dissertations

This dissertation is aimed at understanding two aspects of active surface wave methods to improve the accuracy and reliability of this method. These include (1) the performance of four common wavefield transformation methods for the multichannel analysis of surface wave (MASW) data processing and (2) near-field effects. Toward this end, extensive field measurements were conducted considering different factors affecting these two topics. The MASW and microtremor horizontal to vertical spectral ratio (MHVSR) were then employed to examine their efficiency for infrastructure health monitoring.

Regarding the performance of the four common transformation techniques, it was observed that for sites with a …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Properties Of Concrete Containing Crushed Limestone As Total Replacement Of Natural Sand And Recycled Engine Oil, Mohammad El Bast M. El Bast, Jamal Khatib, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

The rapid growth in the construction industry at the global level has made concrete the most widely used construction material throughout the world. Accordingly, the consumption of natural sand which is one the main raw material constituent of concrete is continuously growing. The demand for river sand is highly increasing due to its scarcity in the market. Manufactured sand produced by crushed rock is being considered as an appropriate alternative to replace river sand in concrete. In recent years, there is a growing interest in the use of crushed sand obtained from limestone quarries in some countries where river sand …

The Utilization Of Industrial Hemp As A Structural Material, Matthew C. Wirick

Construction Management

The need for alternative materials within the construction industry is increasing as more projects are undertaken. Many of the natural resources currently used are being depleted. Various alternatives, such as using recycled concrete as a replacement for aggregate, are being researched and applied to projects with the purpose of reducing construction waste. However, substitutes are needed especially when it comes to structural materials. Industrial hemp is a fast-growing fibrous plant that can be made into a variety of goods and has properties that give it a high enough strength to be fabricated into products that can handle loads such as …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Context-Aware Sensing And Fusion For Structural Health Monitoring And Night Time Traffic Surveillance, Xinxiang Zhang

Electrical Engineering Theses and Dissertations

Rapid developments in computer vision technologies have been transforming many traditional fields in engineering and science in the last few decades, especially in terms of diagnosing problems from visual images. Leveraging computer vision technologies to inspect, monitor, assess infrastructure conditions, and analyze traffic dynamics, has gained significant increase in both effectiveness and efficiency, compared to the cost of traditional instrumentation arrays to monitor, and manually inspect civil infrastructures and traffic conditions. Therefore, to construct the next-generation intelligent civil and transportation infrastructures, this dissertation develops a comprehensive computer-vision based sensing and fusion framework for structural health monitoring and intelligent transportation systems. …

Reliability Of Sfrp-Strengthened Rc Bridge Columns Subjected To Blast Loads, Ahmad Alsendi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The reliability of reinforced concrete bridge columns strengthened with externally bonded, steel-fiber reinforced polymer fabric subjected to blast loads was investigated. Columns were modeled with a nonlinear finite element approach that considers material damage, fracture, and separation. Different concrete strengths, longitudinal reinforcement ratios, and gravity and blast load levels were considered, while uncertainties in material strength and stiffness parameters, as well as load characteristics, were incorporated in the probabilistic analysis. It was found that the use of SFRP can allow significant increases in blast load while maintaining the same level of column reliability.

Development Of An Ultraviolet Absorbance Assay To Estimate Air Entrainer Dosing For Concrete Containing Fly Ash, James Spencer

Graduate Theses and Dissertations

Fly ash is a coal combustion byproduct that can be used as a supplementary cementitious material (SCM) in concrete, offering benefits such as increased workability, durability, and strength. Fly ash can be used as a partial replacement to cement, reducing concrete productions costs and decreasing disposal in landfills. However, variability of fly ash properties (e.g., carbon content, adsorption site density) confounds estimates of the air entraining admixture (AEA) dose needed to achieve a specified air content in concrete. Air entrainment is needed to improve freeze-thaw resistance and limit concrete cracking. The foam index (FI) test is currently used to estimate …

Comparison Of The Resistance Of Belitic Calcium Sulfoaluminate Cement And Portland Cement To Sulfate Attack And Sulfuric Acid, Rilye Dillard

Graduate Theses and Dissertations

Microbially induced corrosion (MIC) is a fairly common concrete deterioration mechanism with many negative effects. MIC is a complex chemical and biological process that occurs in sewage systems and is nearly impossible to replicate in a laboratory setting. For this study, sulfate and sulfuric acid attack on concrete were studied to mimic two stages of the MIC process. The ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution and a modified ASTM C1012 accelerated method were used to compare the sulfate resistance of belitic calcium sulfoaluminate (BCSA) cement, portland cement (PC), and PC-fly …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Aly Mousaad Aly, Faiaz Khaled

Faculty Publications

Large-eddy simulation (LES) has proven to offer superior accuracy in regards to predicting surface pressures compared to the Reynolds-averaged Navier Stokes (RANS) models. However, the primary impediment is the high computational cost associated with LES. The authors attempt to investigate the computational cost and accuracy by employing different sub-grid scale (SGS) models in LES and hybrid RANS-LES models. One of the prerequisites of accurate pressure estimations is to ensure a horizontally homogeneous empty computational domain. This study aims to compare the computational competence qualitatively and quantitatively using an empty domain in regards to the ability to maintain horizontal homogeneity. The …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

No abstract provided.

Advanced Concrete Composites For Improved Performance: A Bibliometric Survey, Dhruv Patel, Aryan Tiwari, Nishnat Nikhare, Rohit Shinde, Ashutosh Dubey, Manan Shah, Shalaka Hire, Sayali Sandbhor

Library Philosophy and Practice (e-journal)

Concrete is the core component of any civil engineering construction. Conventional concrete can be modified depending upon the needs and requirements of the construction. Such concrete is called advanced concrete and this report aims to study advanced concrete and its composites. The main objective of this report is to perform a bibliographic survey on the latest research literature available under the domain of advanced concrete composites for improved performance. Timespan considered for the survey is from the year 2015 to 2020. The bibliographic survey consists of literature from online platforms such as the Web of Science (WoS) and Scopus database. …

A Critical Analysis Of The Application Of Visual Programming To Increase Efficiency In Bim Object Metadata Delivery Workflows During The Delivery Phase Of An Asset, Kieran Lakhera O'Shea, Davitt Lamon

Reports

Uniclass 2015 data generally seems to be overlooked in favour of the more valuable COBie data when discussion begins about BIM model metadata and, at present, few studies are devoted to it and its delivery through automated methodologies. Classification is a key part of the BIM process – without the ability to distinguish one object from another a BIM model lacks the definition required for implementing downstream applications such as functional simulations, compliance checking and other automated technologies. The use of classification data is, of course, not the only way of identifying objects but it is currently the only standardised …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Evaluación Analítica De Parámetros No Considerados En La Formulación De Resistencia Nominal De Conectores Tipo Espigo, José David Ovalle Fernández, William Oswaldo Ramírez Patiño

Ingeniería Civil

Existe una gran variedad de sistemas estructurales, cada uno con características específicas para el soporte de cargas verticales y horizontales. Uno de ellos, el sistema compuesto, el cual es desarrollado buscando ventajas como: la optimización del uso de los materiales combinando ambos en una unidad estructural, el uso de mayores luces entre columnas; la posibilidad de reutilización de la estructura; reducción de los costos de construcción debido a la disminución de tiempos en obra; de tamaño de columnas y cimentación; además, del aumento de protección contra el fuego y corrosión.

Con la aplicación de tecnologías como la soldadura, fue posible …

To What Extent Can Innovative International Project Delivery Strategies (Which Leverage Bim) Improve The Cost Certainty Of Large Complex Public Procurement Projects In The Context Of Irish Public Procurement?, Bim Tudublin, Roqaya Abouklaib

Capstone Reports

Cost overrun is one of the biggest issues in the construction sector, and cost certainty is one of the main aims of the public construction sector in Ireland. Studies have shown that multi-disciplinary collaboration will benefit a construction project throughout its lifecycle. BIM, Lean, and IPD are independent methodologies that encourage collaborative work, and there are existent effective synergies among these concepts. The synergetic innovative international strategies were utilised for delivering large complex projects successfully globally, and many authors have studied large complex public projects that have adopted innovative international project delivery strategies collaboratively and have shown that the cost …

A Critical Analysis Of The Application Of Augmented Reality (Ar) For Monitoring And Documentation Of Construction Site Progress In The Irish Aec Industry., Bim Tudublin, Lukasz Sarnot

Capstone Reports

Sarnot, L. (2021) A critical analysis of the application of augmented reality (AR) for monitoring and documentation of construction site progress in the Irish AEC industry, Capstone Project from the MSc in aBIMM

A Critical Examination Of Visual Programming And Generative Design For The Compliance Checking Of Open Plan Office Layouts Against Hse Guidelines Post Covid-19., Bim Tudublin, Ronan Byrne

Capstone Reports

The purpose of this study is to explore the feasibility of Visual Programming (VP) and Generative Design (GD) in assisting employers review open plan office layouts against Ireland’s HSE guidelines implemented in May 2020 in response to Covid-19. The pandemic has affected all areas of life with workplace standards requiring a complete overhaul. This study will attempt to ascertain compliance with natural ventilation and social distancing requirements through the completion of an experimental research study, utilising Computational Design (CD) tools. A GD study will be undertaken to provide the designer with numerous office layout design solutions to evaluate and evolve. …

Opportunities In The Irish Reinforced Concrete Industry For Lean And Bim Adoption, Bim Tudublin, Kieran Mcconnell

Capstone Reports

The Irish Reinforced Concrete (RC) sector has yet to realise the full potential of Building Information Modelling (BIM) and Lean construction. The positive impacts and benefits of both BIM and Lean in the wider Architecture, Engineering and Construction sector are widely recognised; many of these are transferable to the RC sector, but there is limited research and knowledge on practical transference, uses and advantages. This research aims to fill some of the existing knowledge gaps by examining BIM and Lean adoption and awareness in the Irish RC sector across sub-sectors, professions, and organisational levels, and by exploring opportunities for increasing …

A Critical Analysis Of How Large Irish Architectural Practices Responded To Initial Covid-19 Restrictions And The Affect Implementing Remote Working Had On Bim Processes, Policies, And People, Bim Tudublin, John Mcenroy

Capstone Reports

The unprecedent events which transpired in the 88-day period from the 31st of December 2019 to the 27th of March 2020 have changed the world in which we live and work. The outbreak of Coronavirus disease 19 (COVID-19) and the ensuing pandemic which has evolved are descripted as one in a hundred-year events. This paper researched and critically analyses the operations which large Irish Architecture firms initiated during this period in order to facilitate the ability of its employees working from a remote location, focusing on how the People, Processes and Policies of BIM (3 Ps of BIM); adapted to …

To What Extent Can Lean Construction Processes And Principles Be Utilised In The Design Stage Of A Bim Project In The Irish Design And Construction Industry, Bim Tudublin, Barry Sheramn

Capstone Reports

Although different in many ways, Building Information Modelling (BIM) and Lean Construction are two processes that are having a significant impact on the Design & Construction Industry. In recent years, the Irish AECO industry has seen a tenfold increase across numerous construction disciplines with the adoption of new workflows and processes centred around both BIM and Lean methodologies. Existing literature identifies a strong synergistic relationship between the two processes and highlights the opportunity for Lean processes and principles to be implemented into the design stage workflow. This paper investigated existing literature relating to several lean processes currently implemented in the …