Civil Engineering Commons^™

Thermoelectric Properties Of Cement Composite Analogues From First Principles Calculations, Esther Orisakwe, Conrad S.N. Johnston, Ruchita Jani, Xiaolo Liu, Lorenzo Stella, Jorge Kohanoff's, Niall Holmes Dr., Brian Norton, Ming Qu, Hongxi Yin, Kazuaki Yazawa

Articles

Buildings are responsible for a considerable fraction of the energy wasted globally every year, and as a result, excess carbon emissions. While heat is lost directly in colder months and climates, resulting in increased heating loads, in hot climates cooling and ventilation is required. One avenue towards improving the energy efficiency of buildings is to integrate thermoelectric devices and materials within the fabric of the building to exploit the temperature gradient between the inside and outside to do useful work. Cement-based materials are ubiquitous in modern buildings and present an interesting opportunity to be functionalized. We present a systematic investigation …

Comparing The Measured And Thermodynamically Predicted Afm Phases In A Hydrating Cement, Niall Holmes Dr., Mark Russell, Geoff Davis, Mark Tyrer

Articles

In hydrating Portland cements, more than one of the AFm family of calcium aluminates may exist. Depending on the amount of carbonate and sulfate present in the cement, the most common phase to precipitate is monosulfate, monocarbonate and/or hemicarbonate. It has been reported in the literature that hemicarbonate often appears in measurements such as XRD but not predicted to form/equilibrate in thermodynamic models. With the ongoing use of commercial cements such as CEM I and CEM II containing more and more limestone, it is important to understand which hydrate solids physically precipitate and numerically predict over time. Using 27 cement …

Employing Discrete Solid Phases To Represent C-S-H Solid Solutions In The Cemdata07 Thermodynamic Database To Model Cement Hydration Using The Phreeqc Geochemical Software, Niall Holmes Dr., Mark Tyrer, Denis Kelliher

Articles

This paper presents a cement hydration model over time using the cemdata07 thermodynamic database and a series of derived discrete solid phases (DSPs) to represent calcium silicate hydrate (C-S-H) as a binary solid solution with two end-members. C-S-H in cement is amorphous and poorly crystalline with a range of molar Ca/Si ratios from 0.6 to 1.7. It displays strongly incongruent dissolution behaviour, where the release of calcium into solution is several orders of magnitude greater than silicon. It is, therefore, important that any cement hydration model provides a credible account of this behaviour. C-S-H has been described in the cemdata07 …

Review Of Fly-Ash As A Supplementary Cementitious Material, Nikki Shaji, Niall Holmes Dr., Mark Tyrer

Conference papers

This paper presents a review of fly-ash as a Supplementary Cementitious Material (SCM) in concrete in terms of its effects on hydration and durability. The climate change agenda has focused the cement and concrete industry on using low embodied CO2 materials and much effort has been made on incorporating industrial by-products into cement as SCMs. With worldwide cement production (circa 4 billion tonnes) currently accounting for approximately 8% of global CO2 emissions and 7% of industry energy use, the use of suitable SCMs to partially replace cement in concrete is extremely important. However, while coal-fired power stations are in the …

Deriving Discrete Solid Phases From Csh-3t And Cshq End-Members To Model Cement Hydration In Phreeqc, Niall Holmes Dr., Colin Walker, Mark Tyrer, Denis Kelliher

Conference papers

This paper presents a cement hydration model over time using the CEMDATA thermodynamic database and a series of discrete solid phases (DSP) to represent calcium silicate hydrate (C-S-H) as a ternary (CSH-3T) and quaternary (CSHQ) solid solution. C-S-H in cement is amorphous and poorly crystalline with a range of molar Ca/Si ratios = 0.6-1.7 and displays strongly incongruent dissolution behaviour where the release of calcium into solution is several orders of magnitude greater than silicon. It is therefore important that any cement hydration model provides a credible account of this behaviour. C-S-H has been described in the CEMDATA thermodynamic database …

Effects Of Accelerated Carbonation Curing On Co2 Sequestration And On The Compressive Strength Of Concrete Masonry Units, Barry Gilroy, Leon Black, David Thompson, Ronan Hogan, Niall Holmes

Conference papers

The global consumption of Portland cement has risen to over 4 billion tonnes per annum. Its manufacture is energy and carbon intensive and approximately 900 kg of CO2 is emitted into the atmosphere for each tonne of Portland cement produced. The International Energy Agency (IEA) roadmap sets out a goal to reduce emissions due to cement production to 18 % below 2006 levels by 2050. Concrete has the potential to re-absorb CO2 by the process of carbonation, where it reacts with CaO in the concrete to form calcium carbonate. Accelerated carbonation curing (ACC) is a technique for curing fresh concrete …

Modelling The Addition Of Limestone In Cement Using Hydcem, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models can aid in the prediction, understanding and description of hydration behaviour over time as the move towards more sustainable cements continues.

HYDCEM is a new model to predict the phase assemblage, degree of hydration and heat release over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, complements more sophisticated thermodynamic models by predicting these properties over time using user-friendly inputs within one code. A number of functions and methods based on up to date cement hydration behaviour from the literature are hard-wired into the code along with …

Hydcem: A New Cement Hydration Model, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models are useful to predict, understand and describe the behaviour of different cementitious-based systems. They are indispensable for undertaking long-term performance and service life predictions for existing and new products for generating quantitative data in the move towards more sustainable cements while optimising natural resources. One such application is the development of cement-based thermoelectric applications.

HYDCEM is a new model to predict the phase assemblage, degree of hydration, heat release and changes in pore solution chemistry over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, is aimed at …

Introducing A New Cement Hydration And Microstructure Model, Niall Holmes, Anselm Griffin, Bernard Enright, Denis Keliher

Conference papers

This paper presents a new cement hydration model to predict the microstructure evolution of hydrating tricalcium silicate (C3S). The model is written in MATLAB and employs the continuum approach and integrated particle kinetic relationships to show the change in C3S and the growth of Calcium Silicate Hydrate (C-S-H) and Calcium Hydroxide (CH) in the pore space over time.

Cement hydration is a highly complex process. While hydration models should never completely remove experimental analysis, they are an aid to better understand cement hydration and microstructure development by providing a method to analyse a large number of pastes with different cementitious …

Optimising The Performance Of Cement-Based Batteries, Aimee Byrne, Shane Barry, Niall Holmes Dr., Brian Norton

Articles

The development of a battery using different cement-based electrolytes to provide a low but potentially sustainable source of electricity is described. The current, voltage, and lifespan of batteries produced using different electrolyte additives, copper plate cathodes, and (usually) aluminium plate anodes were compared to identify the optimum design, components, and proportions to increase power output and longevity. Parameters examined include water/cement ratio, anode to cathode surface area ratio, electrode material, electrode spacing, and the effect of sand, aggregate, salts, carbon black, silica fume, and sodium silicate on the electrolyte. The results indicate that the greatest and longest lasting power can …

Evaluating A New Cem Iii/A Cement For Concretes Exposed To Harsh Acid Rich Environments, David Thompson, Niall Holmes, John Reddy

Conference papers

The Irish Annex to the European specification, performance, production and conformity of concrete, IS EN 206, recommends CEM III/B cement for acid rich environments containing between 66 to 80% GGBS. However, BS 8500, the UK annex to EN 206 and the British Research Establishment (BRE) Special Digest 1, recommends CEM III/A cement with a GGBS range of 36-65%. This project investigated the performance of a new CEM III/A cement produced by Ecocem Ireland in concretes exposed to such environments using an extensive suite of laboratory tests.

In Ireland, up to €5.8bn will be invested to provide fresh drinking water and …