Civil Engineering Commons^™

Electrochemical Disinfection Of Municipal Wastewater Using Alternating Current, Xavier A. Chavez Reyes

University of New Orleans Theses and Dissertations

This research focused on chlorine-free disinfection of wastewater by complying with today's regulations. The equipment used was a continuous flow electrochemical reactor connected to an alternating current (AC) power supply. The electrodes used were made out of titanium coated with iridium oxide. To determine the inactivation of Escherichia Coli, a bacterial count method based on the USEPA method 1603 was used.

After several experiments it was determined that electrochemical disinfection using AC was not efficient and economic enough to be classified as a viable alternative to chlorine disinfection. It was demonstrated that chlorine can be produced by electrolysis using AC …

Wind And Thermal Effects On Ground Mounted Photovoltaic (Pv) Panels, Chowdhury Mohammad Jubayer

Electronic Thesis and Dissertation Repository

A combination of Computational Fluid Dynamics (CFD) simulations and wind tunnel experiments are carried out to investigate the effects of wind on the aerodynamic loading and heat transfer of a ground mounted stand-alone photovoltaic (PV) panel with tilt angle of 25^o in open country atmospheric boundary layer. Several azimuthal wind directions are considered: Southern 0^o, Southwest 45^o, Northwest 135^o and Northern 180^o. Three dimensional Reynolds-Averaged Navier-Stokes (RANS) approaches with an unsteady solver using Shear Stress Transport (SST) k-ω turbulence closure are employed for the CFD simulations, whereas Particle Image Velocimetry (PIV) and …

An Engineering Approach For The Design Of Archaeological Reburial Systems, Angel Ari Perez Mejia

Theses and Dissertations

Archaeological sites are a non-renewable resource which is often our only link to the past. However, sites are under constant threat of destruction due to construction activities. Civil engineers and archaeologists must the work together to ensure both the continued survival of archaeological sites while allowing for development to continue. Reburial systems, when properly designed and constructed, allow for the protection of archaeological sites while allowing the continued use of the land. However, because reburial as an intentional conservation technique is relatively modern, practice is fragmented and there are no universally accepted guidelines. Current reburial system design relies on prescriptive …

Functionalized Graphitic Nanoreinforcement For Cement Composites, Nima Zohhadi

Theses and Dissertations

Physical and mechanical properties of graphitic nanomaterials, in particular multiwalled carbon nanotubes (MWCNTs) and graphene nano-platelets (GNPs) make them promising candidates for nanoreinforcement of cement composites. The two key challenges associated with the incorporation of MWCNTs and GNPs are to attain uniform dispersion and interfacial bonding within the composite matrix. The effects of three main-stream dispersion techniques (namely, ultrasonication, acid-etching, and surfactant-coating) on the mechanical properties and microstructure of MWCNT- and GNP-cement composites were experimentally studied. Compressive strength tests and different characterization techniques including dynamic light scattering, Raman spectroscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission …

Scheduling Of Container Handling Equipment In Marine Container Terminals, Narges Kaveshgar

Theses and Dissertations

To improve the competitiveness of marine container terminals, it is critical to minimize the makespan of a container vessel. The makespan is defined as the latest completion time among all handling tasks of the container vessel. Lower makespan (i.e. lower vessel turn time) can be achieved through better scheduling of the container handling equipment during vessel operations. The scheduling of terminal equipment is an operational problem, and a detailed schedule for each type of equipment operating in the terminal is necessary. Several studies have applied operations research techniques to optimize the processes of equipment in a terminal. This dissertation investigates …

Context-Sensitive Seismic Strengthening And Repair Of Substandard Confined Masonry, Rahim Ghorbani

Theses and Dissertations

Confined masonry (CM) is a construction system consisting of load-bearing masonry panels that are confined with cast-in-place reinforced concrete tie columns and beams. Due to satisfactory seismic performance, CM has become the predominant low-rise residential construction system in several areas around the world. However, in developing regions, the use of substandard materials, details and construction practices may result in inadequate performance as highlighted in the 2010 earthquakes in Haiti and Chile. In the aftermath of an earthquake, households are often reluctant to reoccupy their dwellings due to concerns about safety of structures. If feasible, preventive (pre-hazard) strengthening or structural repair …

Influence Of Water Chemistry Parameters On The Dissolution Rate Of The Lead (Ii) Carbonate Hydrocerussite, Caitlin Se Kushnir

Electronic Thesis and Dissertation Repository

This work has focused on the kinetic dissolution of the lead (II) carbonate hydrocerussite (Pb₃(CO₃)₂(OH)₂) under four pH conditions (7.5, 8, 9, 10), three dissolved inorganic concentrations (DIC; 10, 20, 50 mg C/L), and three initial hydrocerussite concentrations (10, 20, 50 mg/L) in batch experiments. Experiments were performed in at least duplicate to determine total dissolved lead dissolution curves at short time scales (hr.). All equilibrium dissolved lead concentrations were achieved in 40 minutes or less, and matched trends from previous studies; pH 7.5 and pH 10 corresponding to the highest and …

Determination Of Area Of Fire Origin Through Examination Of Structural Failure And Deformation, Andrew Thomas Tinsley

Doctoral Dissertations

The effects of fire on steel have long been noted and studied. However, a scientific connection between the area of origin for a fire and the amount of steel deformation observed at the scene has never been established. The development and implementation of this type of analysis has the potential to decrease investigation times significantly as the types of structures to which this method would be applicable are typically large, expansive structures. In order to investigate the relationship between structural steel deformations and a fire’s origin, a series of six tests were performed in a smaller size portal frame steel …

Mechanical Properties Of Glass Fiber Reinforced Polymer Bars After Exposure To Elevated Temperatures, Mohammed Abdulqader Jalil Alsalihi

Theses and Dissertations

ABSTRACT

MECHANICAL PROPERTIES OF GLASS FIBER REINFORCED POLYMER BARS AFTER EXPOSURE TO ELEVATED TEMPERATURES

by

Mohammed A. J. Alsalihi

The University of Wisconsin-Milwaukee, 2014

Under the Supervision of Professor Habib Tabatabai

In the past few decades, the use of composite materials has become more widespread in different fields and industries. Part of this increase comes as an answer to the corrosion issues that ordinary steel faces. Fiber Reinforced Polymers (FRP)s offer a number of advantages that make them an adequate solution to challenges in the rapidly developing construction industry. However, the behaviors of these materials at elevated temperatures and their …

Reliability-Based Design And Acceptance Protocol For Driven Piles, Joseph Jabo

Graduate Theses and Dissertations

The current use of the Arkansas Standard Specifications for Highway Construction Manuals (2003, 2014) for driven pile foundations faces various limitations which result in designs of questionable reliability. These specifications are based on the Allowable Stress Design method (ASD), cover a wide range of uncertainties, do not take into account pile and soil types, and were developed for general use. To overcome these challenges it is deemed necessary to develop a new design and acceptance protocol for driven piles. This new protocol incorporates locally calibrated RLFD resistance factors for accounting for local design and construction experiences and practices, as well …

Microbial Community Shifts Caused By Changes In The Primary Oxidant At A Drinking Water Treatment Plant, Connie Marie Moloney

Graduate Theses and Dissertations

Microbial communities resistant to common oxidants can cause concerns for water treatment plants (WTPs). If a bacterium is not fully oxidized during disinfection, these species can impede upon filtration processes or seed biofilms in the distribution system. In an effort to minimize disinfection by-products (DBP's) that result from the reaction of chlorine (Cl2) with natural organic matter, water treatment plants have the option to change their primary oxidant to chlorine dioxide (ClO2). The following study examines the change in microbial communities during the sedimentation process under differing oxidation regimes, specifically chlorine (Cl2) and ClO2 at the local water treatment plant …

Robust Design Of Shield Tunnels ‒ Considering The Longitudinal Variation Of Input Parameters, Wenping Gong

All Dissertations

This dissertation, aimed at developing an improved design methodology for shield tunnels that explicitly considers design robustness against longitudinal variation of input parameters (such as soil parameters). To this end, a new solution model for shield tunnel performance analysis was first developed. In this new model, the random field concept was employed to model the longitudinal variation of input parameters. The input parameters (in the longitudinal domain) that had been generated with Monte Carlo simulation (MCS) were used as inputs for the tunnel longitudinal behavior analysis. Here, the finite element method (FEM) based upon Winkler elastic foundation theory was employed. …

Modeling Sustainability In Renewable Energy Supply Chain Systems, Fei Xie

All Dissertations

This dissertation aims at modeling sustainability of renewable fuel supply chain systems against emerging challenges. In particular, the dissertation focuses on the biofuel supply chain system design, and manages to develop advanced modeling framework and corresponding solution methods in tackling challenges in sustaining biofuel supply chain systems. These challenges include: (1) to integrate 'environmental thinking' into the long-term biofuel supply chain planning; (2) to adopt multimodal transportation to mitigate seasonality in biofuel supply chain operations; (3) to provide strategies in hedging against uncertainty from conversion technology; and (4) to develop methodologies in long-term sequential planning of the biofuel supply chain …

Laboratory Investigation Of Type I And Type Ii Hardened Cement Emulsified Asphalt Mortar, Tyler E. Rutherford

Masters Theses

The research presented in this thesis investigated the mechanical and viscoelastic properties of a relatively new construction building material that has been given a lot of attention in the past decade. Cement emulsified asphalt mortar (CEAM) has unique properties that differ from concrete and asphalt binder alone as this hybrid material combines the high strength of portland cement composites and the flexibility of asphalt materials. Functioning as a damping material for ballastless high-speed rail track bed, CEAM has the potential to be utilized in other areas of construction.

The work presented in this thesis is broken down into two studies, …

Gis Framework For Spatiotemporal Mapping Of Urban Flooding And Analyze Watershed Hydrological Response To Land Cover Change, Sayed Joinal Hossain Abedin

UNLV Theses, Dissertations, Professional Papers, and Capstones

Urban flooding is a manmade disaster, and a recurrent problem in cities around the globe. Increased surface imperviousness due to urbanization along with inadequate drainage infrastructure system are the chief culprits for urban flooding. Flooding in an urban area brings about severe economic, structural, and environmental damages, and can be associated with casualties too. In order to evade flooding, an efficient flood model is imperative to study current flooding, and analyze flooding behavior to urban surface characteristics.

This research aims to develop a framework using Geographic Information System (GIS) to perform modeling and mapping of flood spatiotemporal variation in urban …

High Strength Steel Fiber Reinforced Flow-Able Or Scc Concrete With Variable Fiber By Volume Fractions For Thin Plate And Shell Structures, Abebe Berhe

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this study is to incorporate discrete, short, mechanically deformed, small diameter steel fibers into high strength concrete with f'c > 70 MPa (10 ksi) in an attempt to reduce and partially eliminate the need for steel rebar in concrete construction. By introducing steel fibers to high strength concrete mixture, the overall tensile, compressive and shear strength of the mixture can be improved immensely thus, replacing portions or major parts of the longitudinal, temperature and shrinkage reinforcements. The reduction or elimination of longitudinal and transverse reinforcements in the construction of structural or non-structural members can result in savings in …

Effect Of Caliche On The Behavior Of Drilled Shafts, Rouzbeh Afsharhasani

UNLV Theses, Dissertations, Professional Papers, and Capstones

The current design methodology for a drilled shaft foundation in cohesionless soil is primarily based on ultimate skin friction values of drilled shafts. In order to obtain these values for each soil type, load tests such as Osterberg test are designed and performed. The Osterberg test layout is designed to estimate the capacity of drilled shaft by applying an upward load during the test and then calculating the downward capacity assuming the upward and downward capacity are the same. This method is appropriate for soils not containing caliche layers because caliche layers bond to the shaft and prevent skin friction …

Modeling Pavement Distress Rates Within U.S. Air Force Airfields, Lauren Sahagun

UNLV Theses, Dissertations, Professional Papers, and Capstones

Through the review of Pavement Condition Index (PCI) surveys completed at Air Force installations scattered across the continental United States, pavement engineers at the Air Force Civil Engineer Center propose that the predominant factor contributing to pavement distress development is climate. They suggest that within each pavement distress type (i.e. alligator cracking, rutting, spalling, etc.) a geographic pattern exists that is strongly correlated to the conventional climate zones within the US. Knowledge of these geographic patterns would equip pavement engineers and asset managers with a powerful tool to develop purposeful maintenance strategies specific to each distress type.

The following approach …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

Sci Cleveland: Inman Street Infrastructure Improvements, Drew B. Keller

Chancellor’s Honors Program Projects

No abstract provided.

Primary Creep In Astm A325 Bolts Under Simulated Fire Loading, Mohammad Matar

Theses and Dissertations

At room temperature, small creep effects are present on steel structures. This is not the case at fire condition where the temperature is much higher than room temperature; in this case creep can be significant, and should be taken into consideration. Since fire hazard can happen in any building, creep effect must be taken into consideration when designing a building. Creep strain behaves as a function of time, temperature and stress. As the temperature increases, the creep strain increases. Similarly, the longer the temperature at a given stress on the structure, the more the creep strain present.

The smallest component …

Early-Age Hydration Studies Of Portland Cement, Fengjuan Liu

Electronic Theses and Dissertations

Our current knowledge on cement hydration during setting is based on the discrete observation of hydrated paste. An advanced micro/nano-level technique which can perform the in-situ observation on the continuous hydration of cement paste is demanded. In this study, Raman spectroscopy (RS) was chosen as such a method to continuously investigate wet pastes. The objective of this research is to explore the hydration process and microstructural development of fresh pastes with this technique. This research was conducted in three phases. First, the RS analysis was used to continuously observe the cement hydration from 20 minutes after mixing to 9 hours. …

Economic Analysis Of Michigan Commercial Vehicle Enforcement Strategies, Randy José Jorge Díaz

Masters Theses

Transportation infrastructure is an essential component of a nation’s success as it allows efficient transportation of goods to all economic markets, providing economic stability and ensuring trade competiveness. Nearly 70 percent of all of Michigan’s freight is shipped by truck and Michigan is ranked eighth in the USA in terms of the value of its exports with $50 billion per year. Unfortunately, commercial vehicles also contribute to the deterioration of pavement, reducing air quality and potentially influencing road safety. To enforce commercial vehicle laws and regulations, most states utilize fixed weigh stations supplemented with other enforcement strategies. Although fixed weigh …

Virtual Analysis And Evaluation Of Roundabout Safety And Operational Features, Elisha Jackson Wankogere

Masters Theses

Roundabouts can be a solution to safety concerns present at other types of intersections. Recently in the United States, there has been an increase in conversion of problematic intersections to roundabouts to improve their safety. However, it is difficult to make these roundabouts, especially multi-lane roundabouts, safe to all ranges of users. Roundabout features such as advance warning and signage play an important role in determining driver performance as they navigate the roundabout.

This research is an effort to evaluate new and existing roundabout safety and operational features such as signs and pavement markings and how they influence performance of …

Stochastic Wavenumber Estimation: Damage Detection Through Simulated Guide Lamb Waves, Garrison Stevens

All Theses

Structural Health Monitoring (SHM) is a field of research that seeks to identify the onset of damage in infrastructure systems such that catastrophic failures can be averted. Acoustic Wavenumber Spectroscopy (AWS) is an emerging SHM technique that can identify and locate change of thickness resulting from damage in thin plates through the estimation of the characteristic wavenumber. AWS measures the ultrasonically induced vibrations of thin plates by laser scanners and monitors the propagation of Rayleigh-Lamb waves through the structure. This method is particularly suitable for thin-walled structures such as those contained in pipes, airplanes, and wind turbine blades. While AWS …

Geotechnical Analysis Of The Foundation Of Fort Sumter National Monument Using Numerical Modeling, Daniel Kyser

All Theses

The foundational condition of the historical coastal fortification of Fort Sumter in Charleston, SC was analyzed though the use of numerical modeling. In this study, two-dimensional Finite Element (FE) analyses were conducted to assess the stability of the foundation-casemates-wall system in a coupled manner subjected to potential loadings such as ocean waves, storm surge and earthquake. The finite element model was verified by modeling the historical events (construction between 1820 and 1860, demolition due to artillery bombardment, reconstruction, earthquake, building of the Battery Huger, and the removal of fill from the parade ground) since the construction of the fort in …

Robust Geotechnical Design - Methodology And Applications, Lei Wang

All Dissertations

This dissertation is aimed at developing a novel robust geotechnical design methodology and demonstrating this methodology for the design of geotechnical systems. The goal of a robust design is to make the response of a system insensitive to, or robust against, the variation of uncertain geotechnical parameters (termed noise factors in the context of robust design) by carefully adjusting design parameters (those that can be controlled by the designer such as geometry of the design). Through an extensive investigation, a robust geotechnical design methodology that considers explicitly safety, robustness, and cost is developed. Various robustness measures are considered in this …

Combined Numberical And Experimental Assessment Of Steel Roof Decks Subjected To Windborne Debris, Robert Roper

All Theses

In the summer of 2013, a steel roof deck manufacturer (Company A) approached Clemson University about testing their steel roof decking product to evaluate the performance of the steel roof deck to resist impact from tornado windborne debris using FEMA P-361 Design and Construction Guidance for Community Safe Rooms. To assist Company A in better serving their customers in areas prone to severe wind events and to facilitate use of their products in community safe rooms, debris impact tests were conducted on two cold-formed corrugated steel roof decking products. Community safe rooms are buildings that are constructed in accordance with …

The Relationship Between Bicycles And Traffic Safety For All Road Users, Jasmine A. Martin

Master's Theses

Over the past twenty years bicycle use as a mode of transportation has grown considerably in the United States. Other studies have examined the individual bicyclist’s risk in proportion to the growth in cycling across cities, a phenomenon referred to as ‘safety in numbers.’ This study expands from that research and examines the effect of cyclists on road safety for all road users.

The study examines the roles of bicycle modal split, a city wide analysis, and bicycle infrastructure, a site based analysis, in road safety outcomes. For the city based analysis, twenty years of crash data in 12 California …

Cal Poly India Project, Derek Babine, Austen Hibler, Alex Hernandez

Mechanical Engineering

This report documents the research, ideation, and development of a solution, implemented by the Cal Poly India Sanitation Team per the request of Mr. Harish Bhutani, to solve the problem of hazardous human waste management in poor villages in India. The sponsor envisioned a universal design that would give each household in those villages access to a private toilet system because the current solution is open defecation in water sources and farming fields. The initial constraints required the project be low cost, not use of electricity or water, have the ability to cater to an 8-10 person household, and be …