Civil Engineering Commons^™

Seismic Performance Design Criteria Of Existing Bridge Bent Plastic Hinge Region And Rapid Repair Measures Of Earthquake Damaged Bridges Considering Future Resilience, A K M Golam Murtuz

Dissertations and Theses

The main objective of this research was to evaluate the seismic performance of existing sub-standard reinforced concrete (RC) bridge column-spread footing subassemblies and to quantify the material strain limits through a full-scale experimental program. A total of six column-footing test specimens with pre-1990 construction details were subjected to reverse cyclic lateral loading, utilizing a conventional three-cycle symmetric loading protocol and a protocol representing the demands expected from a CSZ earthquake. Additionally, the tests were designed so that variable axial loading could be applied to simulate the secondary load effects experienced during an earthquake in a column that is part of …

Determinant Factors Of Bicyclist Injury Severity At Signalized And Unsignalized Intersections, Apy Das

Dissertations and Theses

Bicycling is becoming increasingly popular in Oregon and the US in general due to its environment friendliness as well as health benefits. With Oregon's population projected to increase by more than 30% over the next 30 years, improving the safety of the transportation network for persons on bicycles is important. In Oregon, majority of the bicyclist crashes occur at intersections. This thesis seeks to identify the determinant factors that significantly impact bicyclist crash injury severity at intersections. A mixed logit framework that accounts for any unobserved heterogeneity in the data and allows the estimated parameters to randomly vary across observations …

E-Scooter Safety And How To Improve It, Eric Valentino

altREU Projects

In the last few years, electronic scooters have taken over cities as a means of personal transportation. Between 2017 and 2019 alone, over 30 million trips were recorded across over 100 cities in the US. These scooters pose a safety risk, as 20 in 100,000 trips will result in injury of the rider. On top of this, scooters can cause damage to property, injury pedestrians and motor vehicle drivers, as well as obstruct important infrastructure such as wheelchair ramps. For these reasons, it is important to develop an understanding of the factors that contribute to e-scooter related injuries in order …

Distributionally Robust Optimization Utilizing Facility Location Problems, Elijah Kling

Civil and Environmental Engineering Undergraduate Honors Theses

Facility location problems are used in widespread application in transportation, freight, supply chain, and logistics problems. Models can be developed as deterministic, where all parameters are known, or robust, where a parameter has uncertainty. This thesis explores a new method for developing robust formulation and compares the implications of assuming values for this uncertain parameter. Two models are solved, and both are compared against their deterministic counterparts using numerical analysis. By manipulating the input parameters and considering real world implications of the solutions, either the robust or deterministic can show better performance.

Maximum Coverage Facility Location Drone Routing Problem With Multiple Trip Stops, Marie Roza

Civil and Environmental Engineering Undergraduate Honors Theses

Integer linear optimization can be used to formulate routing problems as models to find optimal solutions given a set of inputs and constraints. In this research, Chauhan et al.'s publication, "Maximum coverage capacitated facility location problem with range constrained drones," is expanded upon by modeling a facility location problem with two-to-one drone deliveries. The model analyzes a set of potential facilities that are available to meet the demands of a set of demand points. The drone delivery routes are modeled with the assumption that each opened facility is assigned one drone that can fulfill up to two demand points’ demands …

The Influence Of Shared Mobility And Transportation Policies On Vehicle Ownership, Edgar Bertini Ruas

PSU Transportation Seminars

With the emergence of several new providers of shared mobility services, such as Uber, Biketown and Car2go, there has been the promise of changes to the traditional way of owning and using a vehicle. One potential consequence of the new mobility services is the reduction in vehicle ownership. At the same time, cities are trying to anticipate these changes by reducing the amount of space dedicated to parking. This thesis aims to asses the extent to which new shared mobility and transportation policy strategies (especially parking requirements and transit pass availability) relate to vehicle ownership among residents of multifamily dwellings. …

Webinar: Segmenting The Market For Transportation Demand Management Campaigns, Philip L. Winters, Amy Lester

TREC Webinar Series

Social marketing seeks to develop and integrate marketing concepts with other approaches to influence behaviors that benefit individuals and communities for the greater social good. It is a useful transportation demand management (TDM) planning approach to promote travel behavior change. The purpose of this study was to explore a consumer market segmentation technique successfully used in Europe for its applicability to marketing efforts in the United States. Attitudinal and demographic data were collected from 1900 individuals in Florida, Oregon, and Virginia modeled after the European approach. Clustering analysis was applied to divide the sample into segments so that members of …

Scenarios For Adoption Of Autonomous Vehicle Technologies In Freight, Sabya Mishra

PSU Transportation Seminars

Innovation adoption research has largely ignored organizational adoption, and little work has been done to understand or predict the adoption of innovations by freight organizations. Among the existing innovation adoption theoretical and methodological approaches this seminar will explore which are most appropriate methods for freight organizational adoption. The seminar will present a disaggregate market penetration model for freight transportation organizations adopting connected autonomous vehicle (CAV) technology and demonstrate an application using a case study area in Memphis, TN. The seminar will highlight ongoing and future organizational adoption research for CAVs, and other innovations.

Driver Comprehension Of Permissive Right-Turns With A Flashing Yellow Arrow (Fya), Christopher Monsere, David Hurwitz

PSU Transportation Seminars

This research explored driver comprehension and behaviors with respect to right-turn signal displays with a focus on the Flashing Yellow Arrow (FYA) in a driving simulator and a comprehension survey. Flashing yellow arrows are used in place of other turn signals, such as solid green or flashing yellow or red circles, to indicate that drivers may turn after yielding to oncoming traffic. These turns are considered “permissive.” Turns where no conflicting traffic is present, such as those indicated with a green arrow, are “protected” turns. The flashing yellow arrow’s inclusion in the 2009 Manual on Uniform Traffic Control Devices sped …

Unobserved Heterogeneity And Spatial Correlation: Statistical And Econometric Analyses Of Heavy-Vehicle Hard Braking And Crash Frequency, Jason Anderson

PSU Transportation Seminars

In heavy-vehicles (a truck with a gross vehicle weight rating of greater than 10,000 pounds), a hard braking event is described as an event that prompts the vehicle’s “black box” to record an abrupt change in speed. More specifically, this occurs when the driver applies excess force to the vehicle’s brake. These hard braking events can then serve as a proxy for several factors, such as economic impacts, environmental impacts, and impacts on safety. In the context of the present study, being that approximately one-third of all heavy-vehicle-caused crashes in 2014 were attributed to faulty brakes, there is a need …

Modeling The Impact Of Traffic Conditions And Bicycle Facilities On Cyclists' On-Road Stress Levels, Àlvaro Caviedes, Miguel A. Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

Past research efforts have shown that cyclists’ safety, stress, and comfort levels greatly affect the routes chosen by cyclists and cycling frequency. Some researchers have tried to categorize cyclists’ levels of traffic stress utilizing data that can be directly measured in the field, such as the number of motorized travel lanes, motorized vehicle travel speeds, and type of bicycle infrastructure. This research effort presents a novel approach: real-world, on-road measurements of physiological stress as cyclists travel across different types of bicycle facilities at peak and off-peak traffic times. By matching videos with stressful events, it was possible to observe the …

Safety Effectiveness Of Pedestrian Crossing Treatments, Christopher Monsere

PSU Transportation Seminars

Over the last decade, the transportation agencies in Oregon have systematically enhanced many pedestrian crossings at mid-block locations with Rectangular Rapid Flashing Beacons (RRFBs), Flashing Yellow Beacons (Flash), and high visibility crosswalk markings (Hi-Vis). Enhancements often included the installation of refuge medians. This study explored the safety performance of these enhanced crossings, categorized by enhancement type. Data were collected on 191 crossings that included installation year, geometric features, surrounding land use, traffic volumes, and the number of crashes. Because pedestrian volume at the locations was unavailable, a pedestrian activity level variable was developed. Target crashes for analysis were identified as …

Building Intelligence In The Automated Traffic Signal Performance Measures With Advanced Data Analytics, Tingting Huang, Subhadipto Poddar, Chris Aguilar, Anuj Sharma, Edward J. Smaglik, Sirisha Kothuri, Peter Koonce

Civil and Environmental Engineering Faculty Publications and Presentations

Automated traffic signal performance measures (ATSPMs) are an effort to equip traffic signal controllers with high-resolution data-logging capabilities and utilize this data to generate performance measures. These measures allow practitioners to improve operations as well as to maintain and operate their systems in a safe and efficient manner. Although these measures have changed the way that operators manage their systems, several shortcomings of the tool, identified by talking with signal operators, are a lack of data quality control and the extent of resources required to properly use the tool for system-wide management. To address these shortcomings, intelligent traffic signal performance …

A Simulator-Based Analysis Of Engineering Treatments For Right-Hook Bicycle Crashes At Signalized Intersections, Jennifer Warner, David S. Hurwitz, Christopher M. Monsere, Kayla Fleskes

Civil and Environmental Engineering Faculty Publications and Presentations

A right-hook crash is a crash between a right-turning motor vehicle and an adjacent through-moving bicycle. At signalized intersections, these crashes can occur during any portion of the green interval when conflicting bicycles and vehicles are moving concurrently. The objective of this research was to evaluate the effectiveness of four types of engineering countermeasures – regulatory signage, intersection pavement marking, smaller curb radius, and protected intersection design – at modifying driver behaviors that are known contributing factors in these crashes. This research focused on right-hook crashes that occur during the latter stage of the circular green indication at signalized intersections …

Dynamic Evaluation Of Transportation Structures With Ipod-Based Data Acquisition, Charles Riley

TREC Final Reports

This grant supported coursework and laboratory development and expanded research capacity, promoting (a) innovative learning activities that expose students to cutting-edge methods of bridge structural health and behavior monitoring and (b) research by our growing group of graduate students using developing technologies (specifically, shake tables and iPods with on-board accelerometers). As transportation infrastructure reaches and exceeds its design life, engineering efforts are turning to evaluation, rehabilitation and repair. Accurately assessing structures to determine their future performance and remaining life is becoming a primary job function for many civil engineers.

As part of this project, graduate students worked with the PI …

Design For An Aging Population, Trygve Faste, Kiersten Muenchinger

TREC Final Reports

Older Americans are increasing in numbers and addressing their needs through better public transportation design will improve their quality of life. This study sought to increase understanding of the obstacles faced by people with impairments in vision, hearing and/or mobility, which are common issues for older people, and generate physical product solutions. The research was conducted to conceptualize products, structures and services to reduce or eliminate these obstacles.

With a focus on the Eugene, OR, public bus system, elderly riders were surveyed and interviewed. Designers rode on buses noting what worked well and where problems arose. Five ride-along observations of …

Feasibility Determination Guide For The Road Diet Plus: A Five/Four-Lane To Two-Lane Road Diet, Michael Williams

Civil and Environmental Engineering Master's Project Reports

Road diets are a popular tool for corridor improvement. Road diets are normally defined as the conversion of a four-lane undivided road to a three-lane undivided road made up of two through lanes separated by a center two-way-left-turn-lane (known as a TWLTL). This new configuration has similar vehicular capacity, greater safety and frees up right-of-way for other uses.

This work examines the possibility of going one step, or one lane, further. What is the possibility of reducing five- or four-lane roads to two-lanes? If this is possible, what are the corridor characteristics within which this process would be feasible?

The …

A Practitioner's Guide To Urban Trip Generation, Kristina Marie Currans

TREC Project Briefs

In 1976, the Institute of Transportation Engineers (ITE) compiled their first Handbook of guidelines for evaluating development-level transportation impacts. Decades later, these methods are still ubiquitously used across the US and Canada. Only recently, with the third edition of the ITE Trip Generation Handbook, have new data and approaches been adopted. In this study NITC researcher Kristina Currans takes aim at understanding issues inherent in the collection and application of ITE’s data and methods in various urban contexts. This technology transfer guide touches on the main findings from this work.

Safety Effectiveness Of Pedestrian Crossing Enhancements, Christopher M. Monsere, Miguel Figliozzi, Sirisha Kothuri, Ali Razmpa, Daniel R. Hazel

Civil and Environmental Engineering Faculty Publications and Presentations

Over the last decade, the Oregon DOT and other agencies have systematically implemented many pedestrian crossing enhancements (PCEs) across the state. This study explored the safety performance of these enhanced crossing in Oregon. Detailed data were collected on 191 crossings. Supplemental data items included crossing location information, route characteristics, surrounding land use and crossing enhancement descriptions. Pedestrian volume at the crossing locations was a highly desirable but unavailable data element. To characterize pedestrian activity, a method was developed to estimate ranges for pedestrian crosswalk activity levels based on the land use classification at the census block level and the presence …

An Assessment Of Post-Encroachment Times For Bicycle-Vehicle Interactions Observed In The Field, A Driving Simulator, And In Traffic Simulation Models, Ali Razmpa

Dissertations and Theses

Most safety analysis is conducted using crash data. Surrogate safety measures, such as various time-based measures of time-to-collision can be related to crash potential and used to gain insight into the frequency and severity of crashes at a specific location. One of the most common and acknowledged measures is post-encroachment time (PET) which defines the time between vehicles occupying a conflicting space. While commonly used in studies of motor vehicle interactions, studies of PET for bicycle-vehicle interactions are few. In this research, the PET of bicycle-vehicle interactions measured in the field, a driving simulator, and in a micro-simulation are compared. …

Connected Vehicles And Rural Road Weather Management, Rhonda Young

PSU Transportation Seminars

Changing weather patterns and increases in extreme weather events has led to the deployment of more weather responsive traffic management strategies. As the transportation system moves towards a connected vehicle environment, questions arise as to how connected vehicle technology can support weather responsive systems. The presentation will discuss the use of connected vehicles in a rural environment as providers of mobile weather data. Two projects will be highlighted - a recently completed research project using passenger vehicle CAN-BUS data as weather surrogates, and the ongoing USDOT CV Pilot Deployment Project in Wyoming.

How To Estimate Pedestrian Demand, Kelly Clifton, Patrick Allen Singleton, Christopher D. Muhs, Robert J. Schneider

TREC Project Briefs

There is growing support to improve the quality of the walking environment and make investments to promote pedestrian travel. Such efforts often require analytical non-motorized planning tools to estimate levels of pedestrian demand that are sensitive to environmental and demographic factors at an appropriate scale. Despite this interest and need, current forecasting tools, particularly regional travel demand models, often fall short.

To address this gap, Oregon Metro and NITC researcher Kelly Clifton worked together to develop a pedestrian demand estimation tool. For generations, planners have been using statistical models to forecast travel demand, but these models have traditionally been auto-centered. …

Development Of A Pedestrian Demand Estimation Tool, Kelly Clifton, Patrick Allen Singleton, Christopher D. Muhs, Robert J. Schneider

Civil and Environmental Engineering Faculty Publications and Presentations

Most research on walking behavior has focused on mode choice or walk-trip frequency. In contrast, this study is one of the first to analyze the destination choice behaviors of pedestrians. Using about 4,500 walk trips from a 2011 household travel survey in the Portland, OR, region, we estimated multinomial logit pedestrian destination choice models for six trip purposes. Independent variables included terms for impedance (walk-trip distance); size (employment by type, households); supportive pedestrian environments (parks, a pedestrian index of the environment variable called PIE); barriers to walking (terrain, industrial-type employment); and traveler characteristics. Unique to this study was the use …

Evaluating The Use Of Crowdsourcing As A Data Collection Method For Bicycle Performance Measures And Identification Of Facility Improvement Needs, Miguel A. Figliozzi, Bryan Philip Blanc

Civil and Environmental Engineering Faculty Publications and Presentations

This research developed a smartphone application called ORcycle to collect cyclists’ routes, users, and comfort levels. ORcycle combines GPS revealed route data collection with new questionnaires that try to elicit cyclists’ attitudes as well as comfort levels and factors that influence their perceived comfort and route choice. The new questionnaires were developed to better understand how cyclists’ comfort levels are affected by route characteristics, route stressors, safety reports, cyclists’ demographics, and cyclists’ cycling attitude. Preliminary results show that many trip characteristics, route choice factors, route stressors and demographic variables are correlated with comfort levels. ORcycle is the first statewide deployment …

An Evaluation Of The Neighborhood Traffic Management Program Of Centennial, Colorado, Rolando Gabriel Melgoza

Civil and Environmental Engineering Master's Project Reports

Residential neighborhoods throughout the United States seek to maintain a quality of life where residents can live free of traffic factors adversely affecting their safety. Many communities have adopted a Neighborhood Traffic Management Program (NTMP) to address concerns over cut-through traffic, speeding, and safety. The City of Centennial, Colorado, incorporated in 2001, is a young city and has its own NTMP. Four traffic mitigation projects have been implemented. The objective of this research is to conduct a before and after comparison study of each Centennial NTMP project, to review the NTMP policies of American cities with similar suburban characteristics to …

Evaluating The Effects Of A Congestion And Weather Responsive Advisory Variable Speed Limit System In Portland, Oregon, Matthew Blake Downey

Dissertations and Theses

Safety and congestion are ever present and increasingly severe transportation problems in urban areas throughout the nation and world. These phenomena can have wide-ranging consequences relating to safety, the economy, and the environment. Adverse weather conditions represent another significant challenge to safety and mobility on highways. Oregon is not immune from either of these global issues. Oregon Route (OR) 217, to the southwest of the downtown Portland, is one of the worst freeways for congestion in the state and is also subject to the Pacific Northwest's frequently inclement and unpredictable climate. High crash rates, severe recurrent bottlenecks and highly unreliable …

A Microsimulation Of Novel Intersection Designs, Aman Kinfemichael Woldetinsae

Civil and Environmental Engineering Master's Project Reports

The focus of this project is to see how a turbo roundabout and a protected intersection designs behave when they are applied on two study sites in Portland, OR. PTV VISSM is used to model, analyze and compare the performances of these designs with the existing intersection. In addition, the best features of the protected intersection and the turbo roundabout were combined to create a new intersection design that is safer for the bicyclists and also performs better than the existing intersection.

The analysis is conducted for five different volume scenarios for both the study sites. The results of the …

Roadway Determinants Of Bicyclist Multi-Pollutant Exposure Concentrations, Alexander Y. Bigazzi, Miguel A. Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

Due to poorly quantified traffic-exposure relationships, transportation professionals are unable to easily estimate exposure differences among bicycle routes for network planning, design, and analysis. This paper estimates the effects of roadway characteristics on bicyclist multi-pollutant exposure concentrations, controlling for meteorology and background conditions. Concentrations of volatile organic compounds (VOC), carbon monoxide (CO), and fine particulate matter (PM2.5) are modeled using high-resolution on-road data. This paper also compares exposure differences on immediately parallel high-traffic/low-traffic facilities and is the first study to quantify VOC exposure differences by facility. Results indicate that average daily traffic (ADT) provides a parsimonious way to characterize the …

Dynamic Ventilation And Power Output Of Urban Bicyclists, Alexander Y. Bigazzi, Miguel A. Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

Bicyclist intake of air pollutants is linked to physical exertion levels, ventilation rates, and exposure concentrations. Whereas exposure concentrations have been widely studied in transportation environments, there is relatively scant research linking on-road ventilation with travel conditions and exertion levels. This paper investigates relationships among power output, heart rate, and ventilation rate for urban bicyclists. Heart rate and ventilation rate were measured on-road and combined with power output estimates from a bicycle power model. Dynamic ventilation rates increased by 0.4-0.8% per watt of power output, with a mean lag of 0.8 minutes. The use of physiology (ventilation) monitoring straps and …

Empirical Analysis Of Bus Bunching Characteristics Based On Bus Avl/Apc Data, Wei Feng, Miguel A. Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

Bus bunching takes place when headways between buses are irregular. Bus bunching is associated with longer waiting times for riders, overcrowding in some buses, and an overall decrease on the level of service and capacity. Understanding the temporal and spatial characteristics and the causes and effects of bus bunching incidents from archived bus data can greatly aid transit agencies to develop efficient mitigation strategies. This paper presents methods to identify and visualize specific time periods and segments where bus bunching incidents occur based on automatic vehicle location (AVL) and automatic passenger count (APC) data. The paper also proposes methods that …