Civil Engineering Commons^™

Dynamic Properties Of Railway Track And Its Components : A State-Of-The-Art Review, Sakdirat Kaewunruen, Alexander Remennikov

Faculty of Engineering - Papers (Archive)

Recent findings indicate one of major causes of damages, which is attributed to the resonant behaviours, in a railway track and its components. Basically, when a railway track is excited to generalised dynamic loading, the railway track deforms and then vibrates for certain duration. Dynamic responses of the railway track and its components are the key to evaluate the structural capacity of railway track and its components. If a dynamic loading resonates the railway track’s dynamic responses, its components tend to have the significant damage from excessive dynamic stresses. For example, a rail vibration could lead to defects in rails …

Dynamic Design Guidelines For Prestressed Concrete Sleepers, Alexander Remennikov, Martin H. Murray, Sakdirat Kaewunruen

Faculty of Engineering - Papers (Archive)

Current design philosophy, outlined in AS 1085.14, is based on the analysis of permissible stresses resulting from quasi-static wheel loads and essentially the static response of concrete sleepers. In general, cracking can incur when the bottom fibre stress is larger than tensile strength of concrete. Premature cracking of prestressed concrete sleepers has been detected in railway tracks. The major cause of cracking is the infrequent but high-magnitude wheel loads produced by a small percentage of “out-of-round” wheels or railhead surface defects, which are crudely accounted for in AS 1085.14 by a single load factor. Based on the current design method, …

Dynamic Responses Of Marine Risers/Pipes Transporting Fluid Subject To Top End Excitations, J. Leklong, S. Chucheepsakul, S. Kaewunruen

Faculty of Engineering - Papers (Archive)

This paper deals with the dynamic responses to top end excitation of marine risers/pipes conveying internal fluid. The marine riser is often used as a flexible link between undersea bore head and subsurface offshore platform. The tidal waves and the changes of sea level consistently excite its top end connected to a floating vessel. In order to carry out the performance-based design of the marine risers, the evaluation of their dynamic responses to top end excitations is imperative. In this study, the marine riser is simulated using twodimensional beam elements. Energy functional of the marine risers conveying fluids is derived …

Influence Of Joint Stiffness On The Free Vibrations Of A Marine Riser Conveying Fluid, S. Kaewunruen, T. Mccarthy, J. Leklong, S. Chucheepsakul

Faculty of Engineering - Papers (Archive)

The marine risers are generally used as the main transport means for economic materials and resources discovered undersea. In general, the marine risers are secured at either an offshore platform or a vessel. Both ends of the riser are to be adjusted to obey with the design criteria but in many cases their rotational stiffness is hardly set free for the hinge connection. This paper integrates the analytical investigation and the design consideration for the effects of end supports on the free vibrations of a marine riser conveying fluid. It is well known that resonances of marine risers/pipes can cause …

Phase Unwrapping Insar Image Using Local Energy Minimization Approach, Kusworo Adi, Tati L.R. Mengko, Andriyan B. Suksmono, Hendra Gunawan

Makara Journal of Technology

Phase Unwrapping InSAR Image Using Local Energy Minimization Approach. Reconstruction process of phase data from its cover is called Phase Unwrapping (PU). Ideally, without any noise phrase, singularity, and aliasing problems, the phase information can be unwrapped easily. However, in fact, the phase data actually always get noise disturbance and discontinuity. The PU process becomes more complicated and needs a better PU algorithm to address the problems properly. In this research, the local PU algorithm is developed using minimization of close related firstorder pixels energy approach. In this method, the energy difference between four close related pixels is counted, followed …

Spectral Response Surfaces And The Ringing Response Of Offshore Structures, I Ketut Suastika

Makara Journal of Technology

A method, called spectral response surface method, is proposed for the study of the ringing phenomenon of offshore structures. Newman’s results for diffraction force on a column were reformulated in terms of the frequency components of the ocean surface and their Hilbert transforms. Using a first-order reliability method together with a dynamic model for the structural response, it is straightforward to calculate the ocean surface history most likely to generate an extreme ringing response and the ringing response history.

The Decompositioning Of Volatile-Matter Of Tanjung Enim Coal By Using Thermogravimetry Analyzer (Tga), Nukman Nukman

Makara Journal of Technology

The Decompositioning of Volatile-Matter of Tanjung Enim Coal by using Thermogravimetry Analyzer (TGA). Coal is a nature material which a kind of energy source. The decompotition of coal could analyze by heat treated using thermogravimetry analyzer. The decomposition of the volatile matter for three kinds of Tanjung Enim coal could be known. The value of activation energy that be found diference, then for Semi Anthracite, Bitumonius and Sub Bituminous Coal, the initial temperatures are 60.8 oC, 70.7 oC, 97.8oC, and the last temperatures are 893.8 oC, 832 oC, 584.6oC.

Isolation Of Methyl Laurate From Coconut Oil As Raw Material For Fatty Alcohol Sulfate, Rita Arbianti, Tania Surya Utami, Astri Nugroho

Makara Journal of Technology

Isolation of Methyl Laurate from Coconut Oil as Raw Material for Fatty Alcohol Sulfate. Methyl laurate is a raw or base material for many industries, including surfactant industries. In this research, coconut oil (VCO) is transesterified with methanol to produce methyl ester, using NaOH as the catalyst. Methyl laurate is then separated by method based on the difference in melting point. This research focuses at determining the effects of some variables in transesterification on the concentration of produced methyl laurate. The variables are temperature (40 oC, 50 oC, 60 oC, 80 oC), time of transesterification reaction (0,5 hour, 1 hour, …

Hydrogen Absorption In Weldments Of Overlaid Claded Pressure Vessel, Ronnie Higuchi Rusli

Makara Journal of Technology

Cracks was found in type 347 stainless steel internal attachment welds of a reactor for a high temperature, and high pressure hydrogen service. One of the possible causes of cracking is low cycle fatigue cracking induced by repetition of thermal stress to embrittled weld metal. Type 347 weld metal loses its ductility by presence of sigma phase and hydrogen.

Physical Characteristics And Utilization Oft The Karst Beaches In Kabupaten Gunungkidul, Astrid Damayanti, Ranum Ayuningtyas

Makara Journal of Technology

Physical Characteristics and Utilization oft the Karst Beaches in Kabupaten Gunungkidul. Karsts beaches at Gunungkidul Regency (Baron, Kukup, Sepanjang, Drini, Krakal, Ngandong, and Sundak), located in south of Daerah Istimewa Yogyakarta Province, have economic potential. Even they have similarity in geological condition (genesis and morphological processes), but they have different physical characteristics. Based on result of observation environment on morphological conditions and spatial analysis method, we found the proper utilization of the beaches.

Neutron Irradiation On Ss316 Material For Radioactive Endovascular Stent Production, Rohadi Awaludin, Abidin Abidin, Sriyono Sriyono

Makara Journal of Technology

Neutron Irradiation on SS316 Material for Radioactive Endovascular Stent Production. It was reported that restenosis could be prevented by radioactive endovascular stent. SS316 material of endovascular stent has been irradiated at pneumatic rabbit system of G.A. Siwabessy reactor for 5 minutes for producing radioactive stent by neutron activation. After 10 days of decay, the irradiated SS316 was measured by gamma spectrometer. The radioisotopes of 51Cr, 59Fe and 60Co were detected in the irradiated SS316 with radioactivity of 5990, 107 and 109 Bq/mg respectively. The Calculation results showed that radioisotopes of 51Cr, 59Fe and 55Fe were produced by neutron activation. The …

Two Element Microstrip Antenna Array With Defected Ground Structure, Fitri Yuli Zulkifli, Eko Tjipto Rahardjo, Muhamad Asvial, Djoko Hartanto

Makara Journal of Technology

Two Element Microstrip Antenna Array with Defected Ground Structure. This paper presents a two element microstrip antenna array using trapezium shape defected ground structure (DGS). The DGS is inserted in the ground plane between two elements of antenna array. Insertion of the DGS is intended to suppress the mutual coupling effect produced by antenna array. Simulation and measurement results were taken and compared between antenna array with and without DGS. Measurement results show that the antenna with DGS compared to antenna without DGS can suppress mutual coupling effect to 7.9 dB, improve the return loss to 33.29% from -30.188 dB …

Impact Damage Classification Of Railway Prestressed Concrete Sleepers, Sakdirat Kaewunruen, Alexander Remennikov

Faculty of Engineering - Papers (Archive)

Commonly, railway tracks suffer with the extreme loading conditions, which are attributed to the train operations with either wheel or rail abnormalities such as flat wheels, dipped rails, etc. These loads are of very high magnitude but short duration, as well as they are of low-possibility occurrence during the design life of the prestressed concrete sleepers. In spite of the most common use of the prestressed concrete sleepers in railway tracks, their impact responses and behaviours are not deeply appreciated nor taken into the design consideration. Up until recently, a new limit states design approach, whereas the dynamic effects are …

Predicting The Seismic Behavior Of The Dywidag Ductile Connector (Ddc) Precast Concrete System, Elizabeth Mary Kenyon

Master's Theses

Structural engineering is heavily dependent on the use of computers. When creating a building model using structural analysis software, it is required that the designer have an understanding of the system behavior and the modeling program capabilities.

Some engineers in the Southern California region are taking steps towards incorporating the Dywidag ductile connector (DDC) and super hybrid systems into building practice due to the advantages found in these systems’ construction methods and seismic performance.

As the DDC and super hybrid systems reach industry, the design engineer will need to model these systems using structural analysis programs. This report describes two …

Reliability Assessment Of Railway Prestressed Concrete Sleepers, Sakdirat Kaewunruen, Alexander Remennikov

Faculty of Engineering - Papers (Archive)

This paper carries out the assessment of reliability indices of railway prestressed concrete sleepers designed in accordance with Australian Standard: AS1085.19. The current design approach of the prestressed concrete sleeper relies on the permissible stresses over crosssectional area. Loading condition acting on railway sleepers is considered from axle burden and dynamic amplification factor. On the basis of Australian design of railway prestressed concrete sleepers, only service limit states are considered; however, the design challenge is to provide adequate resistance of certain cross sections to both positive and negative bending moments. In this paper, the service limit states functions are formulated …

A Comparison Of Nondestructive Testing Backcalculation Techniques For Rigid And Flexible Pavements, Trenton Ellis

Civil Engineering Undergraduate Honors Theses

In designing new pavements, engineers rely on many different measures to characterize the average traffic, climate and soil conditions of the region. Of those, soil conditions are the most elusive, but are also the most crucial for designing a pavement of proper thickness and stiffness. This problem is compounded when the design is for an overlay instead of a new pavement. For overlay designs, engineers require a quantitative characterization of the strength of the existing pavement as well as the underlying soil. Especially for new Mechanistic-Empirical design procedures, direct measures and/or estimates of pavement stiffness are essential inputs. A variety …

The Development Of Inverter Fuzzy Logic Control For Induction Motor Control By Vector Control Method In Electric Vehicle, Era Purwanto, Mohammad Ashary, Subagio Subagio, Mauridhi Heri Purnomo

Makara Journal of Technology

The development of Inverter Fuzzy Logic Control for Induction Motor Control by Vector Control Method in Electric Vehicle. In response to concerns about energy cost, energy dependence, and environmental damage, a rekindling of interest in electric vehicles (EV’s) has been obvious. Thus, the development of power electronics technology for EV’s will take an accelerated pace to fulfill the market needs, regarding with the problem in this paper is presented development of fuzzy logic inverter in induction motor control for electric vehicle propulsion. The Fuzzy logic inverter is developed in this system to directed toward developing an improved propulsion system for …

Substrates Preparation From Woody Tropical Waste Biomass For Biohydrogen Production, Dwi Susilaningsih, Theresia Umi Harwati, Khairul Anam, Yopi Yopi

Makara Journal of Technology

Substrates Preparation from Woody Tropical Waste Biomass for Biohydrogen Production. Addressing to the global warming problem, energy crisis and pollution, hydrogen production by micro-organisms using biotechnological approach should be considered, since it fulfils the recent society requirement to safely produce, renewable and environmental friendly energy. Hydrogen is one of the most promising green energy sources, because it is easily converted to electricity and cleanly combustible. There are three types of micro-organisms for hydrogen production, the first is cyanobacteria through the photosynthesis process, the second is anaerobic bacteria, which use organic substances as electron donor and energy and convert them to …

The Role Of 1 And 9 Wt.% Zn In Precipitation Hardening Of Aa319 Aluminium, Bondan Tiara Sofyan, Sari Susanti, Ridwan R. Yusfranto

Makara Journal of Technology

The Role of 1 and 9 wt.% Zn in Precipitation Hardening of AA319 Aluminium. Aluminium alloys are widely used for automotive application due to its low density and high corrosion resistance. For economic reason, casting of automotive products always uses aluminium scrap as charging materials that may result in fluctuation of content of alloying element, such as Zn. This research studies the role of Zn in precipitation hardening of AA319 aluminium alloys. Hardness and tensile testing were conducted to study the mechanical properties of the alloys, while ageing response was followed by hardness measurements. Evolution of microstructures was observed by …

Building Fire Safety Audit At Faculty X, University Of Indonesia, Year 2006, Fatma Lestari, Rm. Yodan Amaral Panindrus

Makara Journal of Technology

Building Fire Safety Audit at Faculty X, University of Indonesia, Year 2006. Fire may cause loss of life, material and valuable assets. The objective of this study is to conduct audit for fire safety and emergency response in the building at Faculty X, University of Indonesia, Depok. The audit results on the building fire safety facilities including emergency response and preparedness are then compared to the Building Code Australia (BCA) and Indonesian regulation on the building fire safety (Kep.MenPU.No 10 and 11/KPTS/2000). The building selected are Building A, B, C, D, F and G. Building classification for A, B, D, …

Ad Hoc On-Demand Distance Vector (Aodv) Routing Protocol Performance Evaluation On Hybrid Ad Hoc Network: Comparison Of Result Of Ns-2 Simulation And Implementation On Testbed Using Pda, Riri Fitri Sari, Abdusy Syarif, Bagio Budiardjo

Makara Journal of Technology

Ad Hoc on-Demand Distance Vector (AODV) Routing Protocol Performance Evaluation on Hybrid Ad Hoc Network: Comparison of Result of Ns-2 Simulation and Implementation on Testbed using PDA. In Mobile Ad hoc NETwork (MANET), node supplemented with wireless equipment has the capacity to manage and organise autonomously, without the presence of network infrastructures. Hybrid ad hoc network, enable several nodes to move freely (mobile) to create instant communication. Independent from infrastructure. They could access the Local Area Network (LAN) or the Internet. Functionalities of ad hoc network very much dependent on the routing protocol that determines the routing around node. Ad …

Internet Congestion Control System, Pranoto Hidaya Rusmin, Carmadi Machbub, Agung Harsoyo, Hendrawan Hendrawan

Makara Journal of Technology

Internet Congestion Control System. Internet congestion occurs when resource demands exceeds the network capacity. But, it is not the only reason. Congestion can happen on some users because some others user has higher sending rate. Then some users with lower sending rate will experience congestion. This partial congestion is caused by inexactly feedback. At this moment congestion are solved by the involvement of two controlling mechanisms. These mechanisms are flow/congestion control in the TCP source and Active Queue Management (AQM) in the router. AQM will provide feedback to the source a kind of indication for the occurrence of the congestion …

Biomass Production Chlorella Vulgaris Buitenzorg Using Series Of Bubble Column Photo Bioreactor With A Periodic Illumination, Anondho Wijanarko, Dianursanti Dianursanti, Muryanto Muryanto, Josia Simanjuntak, Praswasti Pembangun Dyah Kencana Wulan, Heri Hermansyah, Misri Gozan, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

Chlorella vulgaris Buitenzorg cultivation using three bubble column photo bioreactors arranged in series with a volume of 200 mL for 130 hours shows an increase of biomass production of Chlorella vulgaris Buitenzorg up to 1.20 times and a decrease of the ability of CO2 fixation compared to single reactor at a periodic sun illumination cycle. The operation conditions on cultivation are as following: T, 29.0oC; P,1 atm.; UG, 2.40 m/h; CO2, 10%; Benneck medium; and illumination source by Phillip Halogen Lamp 20W /12V/ 50Hz. Other research parameters such as microbial carbon dioxide transferred rate (qco2), CO2 transferred rate (CTR), energy …

A Study Of Co2 Absorption Using Jet Bubble Column, Setiadi Setiadi, Nita Tania Hadiyani, Hantizen Hantizen, Dijan Supramono

Makara Journal of Technology

A Study of CO2 Absorption Using Jet Bubble Column. The phenomenon of plunging jet gas-liquid contact occurs quite often in nature, it's momentum carries small air bubbles with it into the reactor medium. The momentum of the liquid stream can be sufficient to carry small bubbles completely to the bottom of the vessel. A stream of liquid falling toward a level surface of that liquid will pull the surrounding air along with it. It will indent the surface of the liquid to form a trumpet-like shape. If the velocity of the stream is high enough, air bubbles will be pulled …

The Effect Of Ozone And Zeolite Concentration To The Performance Of The Treatment Of Wastewater Containing Heavy Metal Using Flotation Process, Eva Fathul Karamah, Setijo Bismo, Hotdi M. Simbolon

Makara Journal of Technology

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process. Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and …

Propuesta Para El Reforzamiento Estructural De La Edificación Denominada Monasterio De Las Hermanas De La Visitación Sector Oficinas, Jose Vicente Perez Ortegon, Wilson Giovanny Patiño Suarez, Einer Chaux Suarez

Ingeniería Civil

No abstract provided.

An Assessment Of The Use Of Structural Deformation As A Method Of Determining Area Of Fire Origin, Andrew T. Tinsley, David J. Icove

Safety, Security and Emergency Management Faculty and Staff Scholarship

Current methodologies of origin investigation have yet to include the structural deformations seen in steel buildings as a viable indicator of the area of origin of a given fire. As many steel structures are of relatively large size, it is often difficult to determine the area of origin using the typical dig and sift methods advocated in NFPA 921, especially if the extent of the fire was large and there were no witnesses as to the origin of the fire. As has been investigated for years, the performance of steel is highly affected by the application of heat. The science …

Estudio Del Comportamiento De Vigas Estructurales De Concreto Reforzado Modelado A Escala Reducida, Jessica Nathaly Sánchez Ruiz, Gastón Guillermo Muñoz Martínez

Ingeniería Civil

No abstract provided.

An Assessment Of The Use Of Structural Deformation As A Method Of Determining Area Of Fire Origin, Andrew Tinsley, David Icove

Andrew T Tinsley

Current methodologies of origin investigation have yet to include the structural deformations seen in steel buildings as a viable indicator of the area of origin of a given fire. As many steel structures are of relatively large size, it is often difficult to determine the area of origin using the typical dig and sift methods advocated in NFPA 921, especially if the extent of the fire was large and there were no witnesses as to the origin of the fire. As has been investigated for years, the performance of steel is highly affected by the application of heat. The science …