Civil Engineering Commons^™

Wind And Thermal Effects On Ground Mounted Photovoltaic (Pv) Panels, Chowdhury Mohammad Jubayer

Electronic Thesis and Dissertation Repository

A combination of Computational Fluid Dynamics (CFD) simulations and wind tunnel experiments are carried out to investigate the effects of wind on the aerodynamic loading and heat transfer of a ground mounted stand-alone photovoltaic (PV) panel with tilt angle of 25^o in open country atmospheric boundary layer. Several azimuthal wind directions are considered: Southern 0^o, Southwest 45^o, Northwest 135^o and Northern 180^o. Three dimensional Reynolds-Averaged Navier-Stokes (RANS) approaches with an unsteady solver using Shear Stress Transport (SST) k-ω turbulence closure are employed for the CFD simulations, whereas Particle Image Velocimetry (PIV) and …

Experimental And Analytical Methodologies For Predicting Peak Loads On Building Envelopes And Roofing Systems, Maryam Asghari Mooneghi

FIU Electronic Theses and Dissertations

The performance of building envelopes and roofing systems significantly depends on accurate knowledge of wind loads and the response of envelope components under realistic wind conditions. Wind tunnel testing is a well-established practice to determine wind loads on structures. For small structures much larger model scales are needed than for large structures, to maintain modeling accuracy and minimize Reynolds number effects. In these circumstances the ability to obtain a large enough turbulence integral scale is usually compromised by the limited dimensions of the wind tunnel meaning that it is not possible to simulate the low frequency end of the turbulence …

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany

Makara Journal of Technology

Soekarno–Hatta Airport is the main gateway for international flights to Greater Jakarta. Its accessibility depends on the inter-city and Sedyatmo toll roads, which causes congestion in peak hours, leading to uncertainty about travel times. The Soekarno–Hatta International Airport Rail Link (SHIARL) is proposed as an alternative mass transportation project, which is expected to provide accessibility and mobility for people and goods to and from the airport. Previously, the project was unattractive to private investors as it was technically and financially unfeasible. Therefore, this research aims to improve the feasibility of the Soekarno-Hatta International Airport Rail Link (SHIARL) by using a …

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Design Of Gan-Based Low-Loss Y-Branch Power Splitter, Retno Wigajatri Purnamaningsih, Irma Saraswati, Nji Raden Poespawati, Elhadj Dogheche

Makara Journal of Technology

We present a Y-branch power splitter design with a multimode section using GaN on Sapphire at telecommunication wavelength. The GaN sample optical properties were also investigated, resulting in a refractive index for the GaN layers nTE=2.289±0.001 and nTM=2.324±0.00. Optimization of the structure parameters for this structure was conducted accurately using BPM methods. The results demonstrated the possibility of realizing a GaN-based Y-branch power splitter for various applications.

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi

Makara Journal of Technology

Among the phenomena that occur as a result of contact between two surfaces is friction sound, in which surface roughness is of great importance. In this study, the parameter of contact stiffness is used to explain the frequency characteristic of vibration generated by the rubbing of flat surfaces under a small load. A 3-disk configuration rubbing method was used, which provides a unique characteristic of the system's frequency response function containing specific information about the rubbing vibrations. It is shown that the peak frequency of the rubbing vibration can be explained by using a two-degrees-of-freedom model incorporating the parameter of …

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman

Makara Journal of Technology

The effect of the sputtering parameters on the mechanical tribology properties of Titanium Aluminum Nitride coating on the tungsten cabide insert tool in the dry turning of tool steel has been investigated. The coating was deposited using a Direct Current magnetron sputtering system with various substrate biases (-79 to -221 V) and nitrogen flow rates (30 to 72 sccm). The dry turning test was carried out on a Computer Numeric Code machine using an optimum cutting parameter setting. The results show that the lowest flank wear (~0.4 mm) was achieved using a Titanium Aluminum Nitride-coated tool that was deposited at …

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide

Makara Journal of Technology

Total hip replacement (THR) is one of the most successful orthopedic surgical procedures for replacing a broken hip joint. In THR, wear may occur at the articulating surface of the acetabular cup and the femoral head. In Indonesia, the country with the largest Muslim population in the world, most of the inhabitants do salat (praying) every day. THR users are banned from doing salat for fear it will damage the hip joint prostheses. The previous wear calculation methods on the hip joint prostheses use the gravimetric, coordinate measuring machine (CMM), profiler, and geometric method. The disadvantages of the previous methods …

Ultra-Wideband Notched Characteristic Fed By Coplanar Waveguide, Rastanto Hadinegoro, Yuli Kurnia Ningsih, Indra Surjati

Makara Journal of Technology

In this paper, a novel Ultra-Wide Band (UWB) notch patch antenna with co-planar waveguide (CPW) fed is presented. This antenna only used one layer and the patch antenna is constructed on the first layer and back to back with CPW fed and bottom part is ground plane. The width notch is used to achieve the UWB characteristic. The results shown that the impedance bandwidth is 1130 MHz (1.662–2.792 GHz) or about 50.7% for VSWR <2.

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue

Makara Journal of Technology

Efficient and continuous production of fullerenes, single-walled carbon nanotubes (SWNTs), and carbon nano-particles has been developed by the JxB arc jet method, where the Lorentz force of magnetic field jets out gaseous carbon particles to the JxB direction. In order to realize continuous mass production of these carbon clusters, the revolverinjection- type arc jet producer (RIT-AJP) has been developed. Production of fullerenes, endohedral metallo-fullerenes, SWNTs, metal-encapsulated carbon nano particles has been examined.

Determination Of Area Of Fire Origin Through Examination Of Structural Failure And Deformation, Andrew Thomas Tinsley

Doctoral Dissertations

The effects of fire on steel have long been noted and studied. However, a scientific connection between the area of origin for a fire and the amount of steel deformation observed at the scene has never been established. The development and implementation of this type of analysis has the potential to decrease investigation times significantly as the types of structures to which this method would be applicable are typically large, expansive structures. In order to investigate the relationship between structural steel deformations and a fire’s origin, a series of six tests were performed in a smaller size portal frame steel …

Aerodynamic Testing Of Variable Message Signs, Debbie Meyer

FIU Electronic Theses and Dissertations

The increasing nationwide interest in intelligent transportation systems (ITS) and the need for more efficient transportation have led to the expanding use of variable message sign (VMS) technology. VMS panels are substantially heavier than flat panel aluminum signs and have a larger depth (dimension parallel to the direction of traffic). The additional weight and depth can have a significant effect on the aerodynamic forces and inertial loads transmitted to the support structure. The wind induced drag forces and the response of VMS structures is not well understood. Minimum design requirements for VMS structures are contained in the American Association of …

Effective Cfrp Retrofitting Schemes For Prestressed Concrete Beams, Herish Abdullah Hussein

Civil & Environmental Engineering Theses & Dissertations

This thesis presents a detailed theoretical study of a number of retrofitting schemes for prestressed concrete beams using carbon fiber reinforced polymer (CFRP) sheets to increase flexural strength and ductility. A simply-supported beam subjected to a gradually increasing uniformly distributed load is adopted for the study with a variety of CFRP retrofiring schemes. Three different types of beam cross sections are included for quantifying the influence of CFRP retrofitting when used in high compression regions in addition to CFRP use in high tension areas. To achieve this goal, nonlinear moment curvature relations are developed and coupled with a finite-difference solution …

Wind-Induced Pressures In Air Permeable, Double-Layer Roof Systems In Regions Of Separated Flow, Jeong Hee Oh

Electronic Thesis and Dissertation Repository

This thesis is concerned with the wind-induced pressure distribution acting on air permeable, double-layer roof systems placed on low-rise buildings. Because of the pressure transmission into the cavity between layers, the pressure difference in the double-layer systems differs significantly from that in a single layer. The interior pressures (in the cavity between layers) are highly correlated with external pressures at the openings on the external surface of the outer layer and thereby, the net wind load for the design of the outer layer is considerably reduced by the pressure equalization between the external and internal surfaces of the outer layer. …

Probabilistic Modeling And Bayesian Inference Of Metal-Loss Corrosion With Application In Reliability Analysis For Energy Pipelines, Hao Qin

Electronic Thesis and Dissertation Repository

The stochastic process-based models are developed to characterize the generation and growth of metal-loss corrosion defects on oil and gas steel pipelines. The generation of corrosion defects over time is characterized by the non-homogenous Poisson process, and the growth of depths of individual defects is modeled by the non-homogenous gamma process (NHGP). The defect generation and growth models are formulated in a hierarchical Bayesian framework, whereby the parameters of the models are evaluated from the in-line inspection (ILI) data through the Bayesian updating by accounting for the probability of detection (POD) and measurement errors associated with the ILI data. The …

Response Of Transmission Line Conductors Under Downburst Wind, Haitham Aboshosha

Electronic Thesis and Dissertation Repository

Electricity is transmitted by Transmission Lines (TLs) from the source of production to the distribution system and then to the end consumers. Failure of a TL can lead to significant economic losses and to negative social consequences resulting from the interruption of power. High Intensity Winds (HIW), in the form of downbursts and tornadoes, are believed to be responsible for more than 80% of the weather-related failure of TLs around the world. The studies reported in this thesis are part of an ongoing extensive research program at Western University focusing on the response of TLs under HIW. Previous investigations conducted …

Instrumentation To Monitor Bridge Foundation On The Crosstown Project, Brian Welch

Journal of Undergraduate Research at Minnesota State University, Mankato

The Crosstown Bridge Monitoring Project is located at the intersection of Highway 62 and Interstate I35W a few miles south and west of downtown Minneapolis. The bridge being evaluated is at a railroad overpass located midway along the Crosstown expansion. This research project involved placing instrumentation on the bridge foundation in order to measure the change in the foundation loading during the course of the construction project. For several years there have been questions pertaining to the forces in the pile foundations that support highway embankments. This project placed strain gages on the pile foundations in order to monitor these …

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya

Makara Journal of Technology

This research evaluated the effect of fungal pretreatment of betung bamboo fibers and enzymatic- and microwaveassisted hydrolysis on the reducing sugar yield. The enzymatic hydrolysis of the pretreated biomass was carried out with cellulase and 10 and 20 FPU/g of substrate in a shaking incubator at 50 °C and 150 rpm for 48 h. The sulfuric acid concentration used in the microwave-assisted acid hydrolysis was 1.0, 2.5, and 5%, either with or without the addition of activated carbon. Microwave irradiation (330 Watt) was applied for 5–12.5 min. The yield of reducing sugar was better with the microwave-assisted acid hydrolysis, and …

The Gaussian Orthogonal Laplacianfaces Modelling In Feature Space For Facial Image Recognition, Arif Muntasa

Makara Journal of Technology

Dimensionality reduction based on appearance has been interesting issue on the face image research fields. Eigenface and Fisherface are linear techniques based on full spectral features, for both Eigenface and Fisherface produce global manifold structure. Inability of them in yielding local manifold structure have been solved by Laplacianfaces and further improved by Orthogonal Laplacianfaces, so it can yield orthogonal feature vectors. However, they have also a weakness, when training set samples have non-linear distribution. To overcome this weakness, feature extraction through data mapping from input to feature space using Gaussian kernel function is proposed. To avoid singularity, the Eigenface decomposition …

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis

Makara Journal of Technology

The needs of smaller size RF varactor is a must today, and MEMS comes to be the potential one. In this paper we proposed an adjustable resonance RF-MEMS varactor by using comb-drive actuators placing in each side of the square movable plate. In our preliminary simulation, we found that the device can work properly but some constraints comes such as the dominancies of harmonic resonance frequencies that influences into the nominal capacitances. Therefore for the next step of development we have to find out the window of the structural dimension for a certain spans and a certain operating frequencies.

Properties Of Lignin From Oil Palm Empty Fruit Bunch And Its Application For Plywood Adhesive, Lucky Risanto, Euis Hermiati, Yanni Sudiyani

Makara Journal of Technology

Lignin from lignocellulosic biomass is a potential biopolymer for wood adhesive. The aims of this study were to characterize lignin isolated from the black liquor of oil palm empty fruit bunch fiber pretreated with steam explosion in alkaline conditions and to examine the bond quality of aqueous polymer isocyanate (API) adhesive prepared from lignin, natural rubber latex (NRL), and polyvinyl alcohol (PVA) as base polymers with isocyanate crosslinkers. Lignin was precipitated from the black liquor by adding hydrochloric acid; then the precipitate was separated by filtration, thoroughly washed with water up to pH 2 and pH 5, and dried. The …

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari

Makara Journal of Technology

In a manufacturing company, manufacturing costs, or component prices, and tolerance will affect the price and the quality of a product. Companies must produce high-quality products with low manufacturing costs in order to keep their products competitive in the market; however, it is difficult to produce a high-quality product with a low manufacturing cost. Companies have difficulties in determining the components to be produced using their own manufacturing facilities (make) or outsourced to their suppliers (buy). Hence, a make or buy analysis is needed to minimize the manufacturing costs and quality loss and to determine the optimum alternative regarding make …

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe

Makara Journal of Technology

As electronic device dimensions are continuously reduced, applied bias conditions significantly change and the transport mechanisms must be reconsidered. Tunneling devices are promising for scaled-down electronics because of expected high-speed operation and relatively low bias. In this work, we investigated the tunneling features in silicon-oninsulator lateral nanowire pn junction and pin junction devices. By controlling the substrate voltage, tunneling features can be observed in the electrical characteristics. We found that the minimum substrate voltage required for tunneling to occur in pn junctions is higher as compared with pin junctions. The main cause of these effects relies in the difference between …

Series-Interconnected Plastic Dye-Sensitized Solar Cells Prepared By Low- Temperature Binder-Free Titania Paste, Erlyta Septa Rosa, Lia Muliani, Shobih Shobih, Jojo Hidayat, Brian Yuliarto

Makara Journal of Technology

The aim of this research is to study dye-sensitized solar cells (DSSC). This was implemented on a flexible polyethylene terephthalate (PET) substrate using a mixture of transparent and scattered mesoporous anatase-titania as the electron transport layer for the photoelectrode. This mixture of anatase titania performed a dual function of light scattering and efficient dye absorption. In this study, a porous nano-TiO2 film was prepared on indium tin oxide (ITO) coated polyethylene terephthalate (PET) by using a binder-free titania paste; on it, a DSSC was fabricated. The paste which contained a mixture of TiO2 nanoparticles, acid chloride, and ethanol was printed …

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto

Makara Journal of Technology

We studied the effect of Argon (Ar) ion irradiation on Fe-Al2O3 nanogranular thin film. X-ray diffraction (XRD) patterns show that the ion dose might promote the growth of the Fe2O3 phase from an amorphous phase to a crystalline phase. The magnetic and magnetoresistance properties were investigated using a vibrating sample magnetometer (VSM) and a four point probe (FPP). The results suggest that percolation concentration occurred at the 0.55 Fe volume fraction and with a maximum magnetoresistance (MR) ratio of 3%. The present MR ratio was lower than that of previous results, which might be related to the existence of the …

Electron Emission Characteristics Of Multi-Gated Field Emitters, Hidenori Mimura, Yoichiro Neo, Toru Aoki, Tomoya Yoshida, Masayoshi Nagao

Makara Journal of Technology

We have developed a multi-gated field emitter (FE) such as a quadruple-gated FE with a three-stacked electrode lens and a quintuple-gated FE with a four-stacked electrode lens. Both the FEs can focus the electron beam. However, the quintuple-gated FE has a stronger electron convergence than the quadruple-gated FE, and a beam crossover is clearly observed for the quintuple-gated FE.

Evaluating The Impact Of Bridge Deck Removal Method On The Performance Of Precast/Prestressed Concrete I-Girders, Shaddi Assad

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

Wide flange precast/prestressed concrete I-girders have been widely used by several State Departments of Transportation (DOTs) in the last two decades. These girders have many advantages over standard AASHTO I-girders. Their wide and thick bottom flange accommodates a large number of prestressing strands and their wide and thin top flange provides a shorter deck span, reduced girder weight, greater stability in construction, and adequate platform for workers. Despite these advantages, the wide and thin top flange might be disadvantageous when it comes to deck removal, as it is more susceptible to damage. Therefore there is a need to investigate the …

Learning From Earthquakes: 2014 Napa Valley Earthquake Reconnaissance Report, Erica Fischer

Lyles School of Civil Engineering Graduate Student Reports

Structural damage was observed during reconnaissance after the 2014 South Napa Earthquake, and included damage to wine storage and fermentation tanks, collapse of wine storage barrel racks, unreinforced masonry building partial or full collapse, and residential building damage. This type of damage is not unique to the South Napa Earthquake, and was observed after other earthquakes such as the 1977 San Juan Earthquake, and the 2010 Maule Earthquake. Previous research and earthquakes have demonstrated the seismic performance of cylindrical fluid-filled tanks is controlled by both the tank and the sloshing motion of the liquid inside. Unlike building structures, steel tanks …

Increased Span Length For The Mgs Long-Span Guardrail System, Nicholas A. Weiland

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Long-span guardrail systems have been recognized as an effective means of shielding low-fill culverts while minimizing construction efforts and limiting culvert damage and repair. The current MGS long-span design provided the capability to span unsupported lengths up to 25 ft (7.6 m) without the use of nested guardrail. The excellent performance of the MGS long-span system in full-scale crash tests suggested that longer span lengths may be possible with the current design.

A detailed analysis of the MGS long-span guardrail system was performed using the finite element software program LS-DYNA^®. It was shown that the MGS long-span design …