Civil Engineering Commons^™

Static Analysis Of Structural Members, Amani Calderon, Alexis Villalona, Farhad Alinaghizadeh

Publications and Research

This research is devoted to statics analysis of structural members under mechanical loads. Static analysis of beams under uniform transverse mechanical loads is presented. The beams are supported by simply supported boundary condition at both sides. The equilibrium equation of the beams is obtained and solved using analytical method and numerical method. The numerical method employed in this work is generalized differential quadrature (GDQ) method. The type of differential quadrature method used for numerical solution is the polynomial-based GDQ method. The differential equation is discretized into algebraic equations based on the GDQ technique. The algebraic equations are then solved to …

Model Block Press Design, Ben Todd Van Hamersveld, Chester Wong, Alexander Wing-Jon Giannousis

Mechanical Engineering

This project’s goal is to redesign the Center for Vocational Building Technology (CVBT) BP9 earth block press, which makes 1/3 scale compressed earth blocks to build demonstration model homes in Thailand. The full-scale block press, the BP6, provides a sustainable and affordable technique for constructing habitable homes in Thailand. The BP9 serves as a tool to inform the public of the advantages of human-powered earth block presses through demonstration. The BP9 press design has multiple problems: it is too expensive to manufacture, there is too much friction when used, it has several weak points due to users unintentionally applying excessive …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Study Of Internal Strains Developed In Concrete Decks At Early Ages In Steel Continuous Bridges, Fernando R. Benitez Ortiz

Graduate Theses and Dissertations

The Arkansas Department of Transportation (ARDOT) has identified bridge deck cracking shortly after concrete decks are placed and prior to applying traffic loads. Previous researchers have confirmed improper construction practices and design methods can lead to deck cracking. Currently, many contractors throughout Arkansas are using continuous deck pours. This construction approach may restrict the concrete slab from movement during early age shrinkage, causing tensile stresses to develop. The final stresses at the end of construction must be lower than the concrete tensile strength, if not cracking issues will develop. Eventually, these cracks may enlarge due to service load stresses and …

Green Up Pavement Rehabilitation Design Tool, Dragos Andrei, Robert E. Kochan, Jose H. Perez

Mineta Transportation Institute

While designers produce pavement rehabilitation recommendations every day, for projects of all sizes, most designers have little information on the environmental impact of their recommendations. This research developed a new decision tool, called the “Green Up Pavement Rehabilitation Design Tool,” to allow the comparison of different rehabilitation solutions in terms of greenhouse gas emissions and to encourage sustainable practices such as materials recycling and the use of permeable, cool, and quiet pavement surfaces. The project aligns with the major goal of California Senate Bill 1, which is “to address deferred maintenance on the state highway system and the local street …

Interdisciplinary Student Competition For California Polytechnic State University - San Luis Obispo, Forest G. Gobble

Construction Management

Cal Poly has a reputation for producing some of the best qualified graduates in their respective fields of study. While this is very important, curricular activities involving collaboration between students within the same college are limited (excluding same major). Beyond that, collaboration opportunities across colleges are even more rare. When graduates enter the workforce, many are thrust into highly collaborative environments across various disciplines. Industry professionals have shown a strong desire for young people who have had exposure to realistic problems and experience working with other professions outside of their own field of expertise. The question needing answering is, would …

Investigating The Addition Of Suicide Prevention Barriers To The Natchez Trace Parkway Bridge, Jaideep Thota, Nancy Abdo, Payne Susong, Connor Campbell, Joseph Allston, Meet Patel

Chancellor’s Honors Program Projects

No abstract provided.

Residual Service Life Estimation And Its Importance For Pretensioned Concrete (Ptc) Bridges In Coastal Cities, Dyana Joseline, Deepak K. Kamde, Sripriya Rengaraju, Radhakrishna G. Pillai

International Conference on Durability of Concrete Structures

Many pre-tensioned concrete (PTC) bridges are experiencing premature chloride-induced corrosion. Hence, it is crucial to estimate their residual service life and update it with newer data on a periodic basis - to plan for corrosionpreventionorcontrolmeasuresandensuresafetyofexistingbridges.Criticalchloridethreshold(Cl th) is one of the parameters necessary to estimate the corrosion initiation period. However, quantitative estimates on Clth for prestressing (PS) steel are not well-reported in literature. This paper presents experimental data on the Clth of PS steel, the chloride diffusion coefficient (Dcl), and surface chloride concentration (Cs) of concrete samples obtained from a PTC bridge girder in a coastal city in India. For estimation …

Service Life And Life-Cycle Assessment Of Reinforced Concrete With Fly Ash And Limestone Calcined Clay Cement, Ravindra Gettu, Radhakrishna G. Pillai, Manu Santhanam, Sundar Rathnarajan, Anusha Basavaraj, Sripriya Raju, Yuvaraj Dhandapani

International Conference on Durability of Concrete Structures

Environmental impact due to the emission of carbon dioxide during concrete production can be taken care by reducing the clinker content in the cement. The clinker content can be reduced by replacing it with fly ash and limestone calcined clay. Such systems can have a potential to exhibit enhanced durability/service life when exposed to chloride and carbon dioxide. However, estimating probabilistic service life of concretes with such alternative binder systems is difficult due to the lack of quantitative estimates of the input parameters such as chloride diffusion coefficient (D_Cl), ageing coefficient (m), carbonation coefficient (K_CO2), and …

Bs News November/December

Building Services Engineering

No abstract provided.

Participatory Sensing-Based Geospatial Localization Of Distant Objects For Disaster Preparedness In Urban Built Environments, Hongjo Kim, Youngjib Ham

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Although the benefit of participatory sensing for collecting local data over large areas has long been recognized, it has not been widely used for various applications such as disaster preparation due to a lack of geospatial localization capability with respect to a distant object. In such applications, objects of interest need to be ro- bustly localized and documented for supporting data-driven decision-making in site inspection and resource mobilization. However, participatory sensing is inappropriate to localize a distant object due to the absence of ranging sensors in citizens' mobile devices; thus, the localization accuracy varies to a large extent. To address …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Data

Corresponding data set for Tran-SET Project No. 18STTAM01. Abstract of the final report is stated below for reference:

"This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Simulation Of The Impact Of Connected And Automated Vehicles At A Signalized Intersection, Hamad Bader Almobayedh, Deogratias Eustace, Philip Appiah-Kubi

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Intersections are locations with higher likelihood of crash occurences and sources of traffic congestion as they act as bottlenecks compared with other parts of the roadway networks. Consequently, connected and automated vehicles (CAVs) can help to improve the efficiency of the roadways by reducing traffic congestion and traffic delays. Since CAVs are expected to take control from drivers (human control) in making many important decisions, thus they are expected to minimize driver (human) errors in driving tasks. Therefore, CAVs potential benefits of eliminating driver error include an increase in safety (crash reduction), smooth vehicle flow to reduce emissions, and reduce …

Vu Villa Structural Design And Rehabilitation, Kolby Sukut

Graduate Theses & Non-Theses

The Vu Villa is a bar and pizzeria which has operated out of the first floor of the Campana building in Butte, Montana since 1967. Construction of the Campana building started in 1894 and was completed before the end of the 19^th century. The Campana building is a two-story building which primarily consists of exterior brick masonry walls and wood framing on the interior. Within the last several decades significant sag has been identified in the second-floor of the building as well as an adjacent staircase. In addition, renovation activities have been discussed for the upstairs which would involve …

Improving The Sustainability Of The Built Environment By Training Its Workforce In More Efficient And Greener Ways Of Designing And Constructing Through The Horizon2020 Bimcert Project, Barry Mcauley, Avril Behan

Conference papers

The construction industry consumes up to 50% of mineral resources excavated from nature, generates about 33% of CO2 present in the atmosphere and is responsible for 40% of total global energy through both construction and operation of buildings. The realisation that current pervasive construction practices now face globalization, sustainability, and environmental concerns, as well as ever-changing legislation requirements and new skills needed for the information age has resulted in technologies such as Building Information Modelling (BIM) becoming a key enabler in navigating these barriers. To assist in overcoming these barriers, a number of funding initiatives have been put in place …

Centres Of Excellence And Roadmaps For Digital Transition: Lessons For Ireland’S Construction Industry, Barry Mcauley, Alan Hore, Roger West

Conference papers

Like most sectors in today’s working world, construction businesses are challenged to work in an increasingly digitised world with sophisticated demands from intelligent clients. So much has been written about the inefficiencies of the construction industry, its fragmentation, lack of collaboration, low margins, adversarial pricing, poor productivity, financial fragility, lack of research and development, poor industry image and relatively weak use of digital solutions. The Irish government recognises the importance of digital innovation to address many of the challenges the construction industry faces. With recent high profile reports of escalating spend on signature public sector projects and weak productivity performance …

Bim In Ireland 2019: A Study Of Bim Maturity And Diffusion In Ireland, Barry Mcauley, Alan Hore, Roger West

Conference papers

In 2017, the BIM Innovation Capability Programme team applied five macro BIM maturity conceptual models to capture the capability of the Irish construction industry and assess its BIM maturity. The results found that while Ireland is mature for modelling processes, it is less developed with regards to collaboration processes and policies. Ireland also ranked poorly when it came to regulatory frameworks, measurements and benchmarks compared to a number of countries which also applied the same conceptual models. At the time, the findings highlighted that Ireland’s diffusion dynamic was middle out, meaning that larger organisations or industry associations were pushing the …

An Investigation Into Current Procurement Strategies That Promote Collaboration Through Early Contractor Involvement With Regards To Their Suitability For Irish Public Work Projects, Barry Mcauley, Frederic Lefebvre

Conference papers

Previous research has established that multi-disciplinary collaboration will benefit a construction project throughout its lifecycle. While Lean Construction, Building Information Modelling (BIM), and Integrated Project Delivery (IPD) can all be viewed as separate processes which add independent value to a project, they are more effective when used in partnership with each other. In order to ensure the high levels of collaboration expected for these processes to work in unison, the early involvement of the Contractor is paramount. Early contractor involvement within the design process can ensure a more focused integrated project team, improvement of both constructability and cost certainty, as …

From Roadmap To Implementation: Lessons For Ireland’S Digital Construction Programme, Barry Mcauley, Alan Hore, Roger West

Conference papers

As part of their Future of Construction initiative in 2018 the World Economic Forum published an action plan to accelerate Building Information Modelling adoption. The WEF report highlighted actions that companies, industry organisations and governments are advised to implement to accelerate BIM adoption and better capitalise on delivering better project outcomes. According the authors of the report BIM is seen as the centrepiece of the construction industry’s digital transformation, however they acknowledged that BIM adoption globally remain slow. Anecdotal experience would suggest that BIM usage in Ireland is also very low and that a similar initiative or an adaptation of …

Delivering Energy Savings For The Supply Chain Through Building Information Modelling As A Result Of The Horizon 2020 Energy Bimcert Project, Barry Mcauley, Avril Behan

Conference papers

The global buildings sector is now responsible for 40% of final energy consumption as well as accounting for 33% of energy-related carbon dioxide emissions. This has resulted in a growing urgency to address energy and emissions from buildings and construction, to meet restrictive 2020 targets as specified by the European Union (EU). To achieve these targets a number of funding initiatives have been put in place through Horizon 2020 with a focus on BIM, due to it having the potential to rapidly produce energy outputs that enable design teams to analyse and compare the most cost-effective, energy-efficient options. However, despite …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Data

Corresponding data set for Tran-SET Project No. 18GTTSA02. Abstract of the final report is stated below for reference:

"This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Strategies For Prioritizing Needs For Accelerated Construction After Hazard Events, Fernando Moreu, Chao Wang, Xinxing Yuan, Laleh Ghanbari, Claudia Garrido

Data

Corresponding data set for Tran-SET Project No. 18PPLSU04. Abstract of the final report is stated below for reference:

"There is a need for rapid and responsive infrastructure repair and construction after natural disaster events such as hurricanes, wildfires, and tornadoes. These natural disasters often shut down basic infrastructure systems, as experienced recently in several Region 6 states as well as in other states around the country. Accelerated construction practices are often used in these situations to speed up the traditional, and often slow, project delivery process. However, after a natural disaster, several and different types of transportation infrastructure components are …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Publications

Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and environmentally friendly alternative than OPC. This research explores methods to develop GPC with desired properties and evaluate their …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Publications

Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized that by adding a thin layer of highly ductile ECC material between the existing pavement and overlay, reflective …

Bs News September/October

Building Services Engineering

No abstract provided.

The Development Of Initial Asphalt Mixture Acceptance Criteria Using The Scb Test And The I-Fit Test, Nathan Delman Parnell

Graduate Theses and Dissertations

Cracking has become the primary asphalt pavement distress in Arkansas. Arkansas along with other states have implemented a test to measure rutting resistance. This paper presents research to implement a cracking resistance test to further modify the Superpave volumetric asphalt mixture design method in Arkansas. The Illinois Flexibility Index Test (I-FIT) was the test chosen to analyze for this research. Two aging methods were tested, a short term oven aging (AASHTO R30 ST) and a long term oven aging (NCAT) method. Six asphalt mixtures were selected to be tested. The mixtures testes were recreated from Arkansas Department of Transportation (ARDOT) …