Civil Engineering Commons^™

Synthesis Of Geopolymer Using Coal Fly Ash And Corn Stover, Anu Paneru

Master's Theses

The development of each nation is dependent on its infrastructure, and nations are competing with others in infrastructure, especially in the construction of roadways, since they play a vital role in the economic and social development of the nation. The conventional materials used for road construction are cement and asphalt, which pose significant environmental challenges. This thesis explores the potential of fly ash (FA) and corn stover (CS) in synthesizing geopolymer, as an alternative material for the construction of roads. The study examines the impact of FA and CS percentages and the particle sizes of CS on the compressive strength, …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Quasi-Static And Impact Load Response Of Bfrp-Reinforced Concrete Beams And Post-Terrorist-Attack Sub-Assemblages, José Luis Carrasquillo

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of a theoretical and experimental study of Basalt Fiber Reinforced Polymer (BFRP) reinforced concrete beams and post-terrorist-attack subassemblages subjected to either quasi-static or impact load. Both BFRP reinforcement as well as BFRP fabric are used in this investigation. The sub-assemblage consists of an otherwise two-span beam converted to a fixed-end single-span one owing to the loss of a middle column blasted off during the terrorist attack. The simply supported beams are subjected to a midspan quasistatic or an impact load. However, each sub-assemblage is subjected to a quasi-static load up to collapse to simulate the …

Understanding Unsteady Corner Separation Within Wing-Body Junction Flows, Paul G. Winner

Doctoral Dissertations and Master's Theses

Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A NACA 0015 wing mounted on a flat plate at an angle of attack of 13°was used as the model junction flow field. The wing had an aspect ratio of 8 with a linear washout twist of 15°. The Reynolds number based on the wing chord was Re_c = 4.5 × 10⁵. Time-dependent stereoscopic particle …

Evaluation Of Aluminum Dissolution, Current Density, And Pitting Patterns During Electrocoagulation, Monica Castro Carias

USF Tampa Graduate Theses and Dissertations

Electrocoagulation (EC) is a sustainable water treatment process involving the generation of coagulants on-site through the application of a voltage on metal (usually aluminum or iron alloys). The factors that impact EC system performance have been well researched, however further research is needed on the factors that impact anodic dissolution of aluminum electrodes, especially when the technology is transferred to full-scale applications. Electrode fouling is one of the factors that can impact dissolution of the anode during EC due to the formation of a protective oxide/hydroxide layer on the electrode surface. Previous studies have addressed electrode fouling by reversing polarity, …

Shale Softening Based On Pore Network And Laboratory Investigations, Di Zhang

Dissertations

This dissertation consists of two major parts: Firstly, experimental investigation of four major shale softening mechanisms and quantifications of structural parameters. Secondly, numerical simulations of nano-scale flow behaviors using the previous experiments determined parameters based on modified pore network modeling.

Hydraulic fracturing is widely applied to economical gas production from shale reservoirs. Still, the gradual swelling of the clay micro/nano-pores due to retained fluid from hydraulic fracturing causes a gradual reduction of gas production. Four different gas-bearing shale samples are investigated to quantify the expected shale swelling due to hydraulic fracturing. These shale samples are subject to heated deionized (DI) …

Valorization Of Secondary Agriculture Residues, Narendra Kumar

Master's Theses

Secondary agriculture residues have the potential to be major contributors as resources for energy and sustainably sourced materials production. Separating secondary agricultural residues, which have already been transported to processing centers, into individual biomass components could convert these wastes into bioproducts. Many types of pretreatments to achieve this separation involve chemicals that are hazardous for the environment. Several deep eutectic solvents (DES) that are biocompatible have been investigated for their ability to deconstruct rice hulls and sugarcane bagasse. Mass yield, enzymatic hydrolysis of the pretreated biomass, fiber analysis, and Fourier transform infrared spectroscopy have confirmed that the DES formic acid:choline …

Valorization Of Secondary Agriculture Residues, Narendra Kumar

Doctoral Dissertations

Secondary agriculture residues have the potential to be major contributors as resources for energy and sustainably sourced materials production. Separating secondary agricultural residues, which have already been transported to processing centers, into individual biomass components could convert these wastes into bioproducts. Many types of pretreatments to achieve this separation involve chemicals that are hazardous for the environment. Several deep eutectic solvents (DES) that are biocompatible have been investigated for their ability to deconstruct rice hulls and sugarcane bagasse. Mass yield, enzymatic hydrolysis of the pretreated biomass, fiber analysis, and Fourier transform infrared spectroscopy have confirmed that the DES formic acid:choline …

Corrosion Rate Prediction In Frp-Concrete Repair, Mohammad A. Khawaja

USF Tampa Graduate Theses and Dissertations

Research has proven that wrapping structural elements with fiber-reinforced polymers (FRPs) slows down chloride-induced corrosion rate but does not stop it. Although FRP has been used for corrosion repair for over 40 years, predictive corrosion rate models for FRP-concrete systems are limited in literature. This dissertation presents an oxygen diffusion-based predictive framework to estimate corrosion rate in FRP-concrete systems.

The dissertation has three main components. First, a core framework that is referred to as Khawaja-Sen-Bhethanabotla (KSB) model. In the KSB model, statistical methods were used to extend experimental data on oxygen permeation coefficients. These data were for one and two …

Analysis And Optimization Of Colorimetric Nanosensors For Rapid Detection Of Microbes In Water, Ruby A. Lang

Master's Theses

Access to safe water is a basic human right recognized by the United Nations General Assembly in 2010 (WHO, 2020). However, a least 2.2 billion people globally still are without safely managed water services meaning they use a drinking water source that can be contaminated with faeces (WHO, 2020). With such a pressing global health issue, it is clear that improvement to water systems is important and required in the Agenda 2030 Sustainable Development Goals (SDGs). However, to improve water systems and prove they are safe water sources, water quality testing must occur. A solution to this issue is the …

Stress-State And Injection-Rate Dependent Damage Processes During The Hydraulic Fracturing Of Granite, Gayani Sasendrika Gunarathna

Dissertations

Hydraulic fracturing is a well-stimulation technique that is employed in field applications, such as enhanced geothermal systems (EGS) and shale oil/gas extraction. This research experimentally investigates the effect of the state of stress and injection rate on the hydraulic fracturing processes. In addition, a displacement discontinuity method (DDM) code, FROCK, is used to model the crack initiation and propagation in a granite specimen under hydraulic fracturing conditions. In order to conduct the experimental work, a test setup capable of applying a triaxial state of stress and water pressure inside pre-fabricated flaws cut in prismatic granite specimens is developed. Additionally, the …

Low-Grade Kaolin Clay Natural Resource For Use As A Supplementary Cementitious Material In Structural Concrete Elements, Brandon X. Lorentz

USF Tampa Graduate Theses and Dissertations

At the turn of the century, low-grade kaolin clay (LGK) was presented as a widely available and potential natural resource of supplementary cementitious materials (SCM) for producing high performance concretes. In using LGK as an SCM, clinker production is reduced, aiding environmental concerns with associated CO2 emissions. These types of clays have very heterogeneous mineralogy and microstructural characteristics, causing unique influences on concrete structural and flow performance, although these influences are not well understood. This research studies LGK natural to the state of Florida and assesses their potential use as high performance SCM.

Ten kaolin clays were obtained through a …

Radical Social Ecology As Deep Pragmatism: A Call To The Abolition Of Systemic Dissonance And The Minimization Of Entropic Chaos, Arielle Brender

Student Theses 2015-Present

This paper aims to shed light on the dissonance caused by the superimposition of Dominant Human Systems on Natural Systems. I highlight the synthetic nature of Dominant Human Systems as egoic and linguistic phenomenon manufactured by a mere portion of the human population, which renders them inherently oppressive unto peoples and landscapes whose wisdom were barred from the design process. In pursuing a radical pragmatic approach to mending the simultaneous oppression and destruction of the human being and the earth, I highlight the necessity of minimizing entropic chaos caused by excess energy expenditure, an essential feature of systems that aim …

Chemical Modification Of Crumb Rubber To Increase Its Bonding With Concrete, Mary T. Mccannon, Kendall J. Sweitzer

Williams Honors College, Honors Research Projects

The hydrophilicity of crumb rubber was increased with wet chemical modification and added to concrete to increase its adhesion with concrete, consequently the compressive strength relative to that of concrete with untreated rubber. Other modification methods were tested on crumb rubber and rubber sheets to yield an increase in hydrophilicity. Certain tests were less reliable for powder testing or tedious and time consuming and concrete materials and rubber may not be homogeneous.

For wet chemical modification, several approaches were attempted. First, crumb rubber was soaked in 5% sodium hydroxide, 5% potassium permanganate and saturated sodium bisulfite, tested for hydrophilicity using …

Nanofiltration Rejection Of Contaminants Of Emerging Concern From Municipal Water Resource Recovery Facility Secondary Effluents For Potable Reuse Applications, Steven Michael Jones

Graduate Theses and Dissertations

As reuse of municipal water resource recovery facility (WRRF) effluent becomes vital to augment diminishing fresh drinking water resources, concern exists that conventional barriers may prove deficient and the upcycling of contaminants of emerging concern (CECs) could prove harmful to human health and aquatic species if more effective and robust treatment barriers are not in place.

There are no federal Safe Drinking Water Act (SDWA) regulations in place specifically for direct potable reuse (DPR) of WRRF effluent. Out of necessity, some states are developing their own DPR reuse regulations. Currently, reverse osmosis (RO) is the default full advanced treatment (FAT) …

Integrated Solar Technologies With Outdoor Pedestrian Bridge Superstructure Decking, Richard K. Racz

Masters Theses

Solar technology has been a major topic in sustainable design for many years. In the last five years, however, the solar technology industry has seen a rapid growth in installations and technological advances in cell design. Combined with a rapidly declining overall system cost, the idea of introducing solar technology into a wider range of applications is becoming a focus for engineers and scientists around the world. So many variables which alter solar energy production, such as the sun and surrounding environment, determine whether a solar design is beneficial. This thesis presents a bridge deck surface integrated with solar cells …

Application Of Treated Oil Sands Drill Cuttings Waste In Micropiles Construction, Moustafa Ahmed Raafat Mohamed Aboutabikh

Electronic Thesis and Dissertation Repository

A micropile is constructed by drilling a hole, placing a steel reinforcing element, grouting it using neat cement. However, cement production consumes energy and generates carbon dioxide. Implementing waste materials in construction applications represents a sustainable solution for many waste management problems. On the other hand, oil sands drill cuttings waste represents one of the most difficult challenges for the oil sands mining sector. Reducing the amount oil sands drill cutting waste sent to landfill offers one of the best solutions for waste management. This thesis presents an innovative solution for application of treated oil sands waste (TOSW) in grout …

Slope Stability Enhancement Of An Upstream Tailings Dam: Laboratory Testing And Numerical Modelling, Yazeed A. Alsharedah

Electronic Thesis and Dissertation Repository

Mine tailings are the byproduct of mining activities, which need to be disposed of once the ore is extracted. They can be disposed of in either dry or wet forms. The latter is most common with the tailings being disposed of in the form of slurry inside retention structures. The retention structure may be a natural, manmade, or built dam, which is the case in most of nowadays mining locations. In this thesis, improving the stability of an upstream tailings dam using soil additives is investigated. The experimental phase of this study involved laboratory tests conducted to characterize mine tailings …

Production And Harvest Of Microalgae In Wastewater Raceways With Resource Recycling, Alexander Colin Roberts

Master's Theses

Microalgae can be grown on municipal wastewater media to both treat the wastewater and produce feedstock for algae biofuel production. However the reliability of treatment must be demonstrated, as well as high areal algae productivity on recycled wastewater media and efficient sedimentation harvesting. This processes was studied at pilot scale in the present research.

A pilot facility was operated with nine CO₂-supplemented raceway ponds, each with a 33-m² surface area and a 0.3-m depth, continuously from March 6, 2013 through September 24, 2014. The ponds were operated as three sets of triplicates with two sets continuously fed …

Feasibility Of Cathodic Protection In Grouted Post Tensioned Tendons - Exploratory Model Calculations, Jacob Dharma Bumgardner

USF Tampa Graduate Theses and Dissertations

Recent corrosion related failures of grouted post tensioned tendons, even after the introduction of improved grouts, have led to renewed interest in supplemental or backup means of corrosion control for these systems. A finite element model is presented to explore feasibility of impressed current cathodic protection of strand in grouted tendons. The model examines polarization evolution as function of service time and includes consideration of anode placement and size, grout porosity, pore water alkalinity, electrochemical species diffusivity and applied voltage on the polarization efficacy and durability of such a system. The exploratory model projections suggested that, within the context of …

Geomechanical Characterization Of Marcellus Shale, Rafael Villamor Lora

Graduate College Dissertations and Theses

Given their potential applications for a number of engineering purposes, the geomechanics of shale reservoirs is becoming one of the most important issues in modern geomechanics. Borehole stability modeling, geophysics, shale oil and shale gas reservoirs, and underground storage of CO2 and nuclear waste are some of these potential applications to name a few. The growing interest in these reservoirs, as a source for hydrocarbons production, has resulted in an increasing demand for fundamental material property data.

Laboratory analysis and constitutive models have shown that rock elastic and deformational properties are not single-value, well-defined parameters for a given rock. Finding …

Development Of Cementitious Materials For Adhesion Type Applications Comprising Calcium Sulfoaluminate (Csa) Cement And Latex Polymer, Joshua V. Brien

Theses and Dissertations--Civil Engineering

The objective of this research was to develop high performing polymer modified calcium sulfoaluminate (CSA) cement materials for use in applications requiring superior adhesion characteristics. Little information is available describing interactions of CSA cement containing minor phase tri-calcium aluminate (C₃A) with commonly used admixtures. Given the scarcity of information, a basic approach for developing cementitious materials was followed. The basic approach consisted of four tasks: cement design, admixture design, polymer design and testing developed materials. The iterative, time consuming process is necessary for understanding the influence of specific constituent components on overall system behavior. Results from the cement …

Kelvin Probe Electrode For Contactless Potential Measurement On Concrete-Properties And Applications, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

The practical feasibility of using a Kelvin Probe as a novel reference electrode in the measurement of both potential and polarization pulse response of reinforcing steel in concrete is demonstrated. Potential values measured using a KP reflect greater stability and repeatability than can typically be attained with conventional reference electrodes. Duplicate reinforced concrete beam test specimens with well-differentiated centrally corroding rebar segments were analyzed using both the Kelvin Probe (KP) and a conventional Saturated Calomel Electrode (SCE). Potential profile maps were developed using potential values recorded under static conditions with both the SCE and the KP. Nominal polarization resistance was …

Oxygen Diffusion Characterization Of Frp Composites Used In Concrete Repair And Rehabilitation, Chandra K. Khoe

USF Tampa Graduate Theses and Dissertations

Many independent studies have conclusively demonstrated that fiber reinforced polymers (FRP) slow down chloride-induced corrosion of steel in concrete. The mechanism for this slow down is not well understood but it has been hypothesized that FRP serves as a barrier to the ingress of chloride, moisture, and oxygen that sustain electrochemical corrosion of steel.

This dissertation presents results from an experimental study that determined the oxygen permeation rates of materials used in infrastructure repair. In the study, the oxygen permeation constants for epoxy, carbon and glass fiber laminates, concrete, epoxy-concrete and FRP-concrete systems were determined and a method developed to …

Halloysite Clay Nanotubes For Controlled Delivery Of Chemically Active Agents, Elshard Abdullayev

Doctoral Dissertations

In this work we explored the capabilities of halloysite nanotubes as capsules for encapsulation and controlled delivery of the chemically and biologically active substances. Halloysite is a two-layered aluminosilicate which has a predominantly hollow tubular structure in the submicron range and is chemically similar to kaolinite [1, 2].

In the first section of this work, we analyzed the structure of the halloysite nanotubes as well as its capability to encapsulate and deliver biologically and chemically active agents, similarities and differences between release characteristics of different agents and how these differences relate with their chemical structure. Models were used to describe …

Arsenite Oxidation By Pure Cultures Of Thiomonas Arsenivorans Strain B6 In Bioreactor Systems, Aniruddha Dastidar

University of Kentucky Doctoral Dissertations

The removal of arsenic toxicity from water is accomplished by a preliminary preoxidative step transforming the most toxic form, arsenite (As (III)), to the least toxic form, arsenate (As (V)). The potential of As (III) oxidation to As (V) was initially investigated in batch reactors using the chemoautotrophic Thiomonas arsenivorans strain b6 under varying initial As (III) and cell concentrations and at optimal pH and temperature conditions (pH 6.0 and temperature 30°C). The strain b6 completely oxidized As (III) to As (V) during exponential growth phase for lower levels of As (III) concentrations (≤ 100 mg/L) but continued into stationary …

Fatigue Of Drill Pipes Used In Horizontal Directional Drilling, Feibai Ma

Doctoral Dissertations

Fatigue is the most common cause of mini-HDD drill rod failure. It can occur at stress levels far below the normal operating stress in most drill stem components. Fatigue failures occur because the drill rod, after it has been forced into a curved path, undergoes a cyclic bending stress oscillating from tension to compression in concert with the other stress components caused by torque, thrust, or pullback.

When a rod breaks underground, there is considerable extra cost caused by the delay in “fishing” out the broken rod as well as the cost of replacing the rod. On the other hand, …