Membrane Science Commons^™

Development Of Novel Sensor Coating Methodology To Enable Understanding Of Fouling Mechanisms On Ion Exchange Membranes, Andrew Ulmer

Honors Theses

As populations expand and natural water resources are depleted, severe droughts and limited access to clean water have become an increased threat to areas across the world. Effective and economic water treatment methods such as electrodialysis (ED) are vital for combating these threats, especially in developing nations and secluded locations. Organic foulant adsorption on the surface of ion exchange membranes severely limits the capabilities of water desalination systems such as ED along with significantly increasing maintenance costs. Understanding characteristics such as the total amount and rate at which these foulants at specific concentrations adsorb and desorb to the membranes is …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

Utilization Of Electrodeionization To Separate And Concentrate Cellobionic And Gluconic Acid, Andie Veeder

Chemical Engineering Undergraduate Honors Theses

Biofuel production is currently an expensive and inefficient process with many drawbacks. It is water and land intensive, competes with food production, and requires large energy inputs decreasing its relative sustainability. This paper explores the use of electrodeionization (EDI) to improve the biofuel process by separating and concentrating large, organic sugar acids that are important materials for the production of bioethanol. An EDI device was assembled for the purpose of separating and concentrating gluconic, cellobionic and lactobionic acid. Several trials were conducted and samples were analyzed to determine the success of this experiment. The results for the separation and concentration …

Removal Of Hexavalent Chromium From Water By Chitosan-Enhanced Ultrafiltration, Putu A. Y. Indiasih, Anindita D. Syaifudin, Nurul Faiqotul Himma, Bambang Ismuyanto

Makara Journal of Technology

Polymer-enhanced ultrafiltration has gained increasing attention as a selective separation process to remove small solutes, such as metal ions, from water or wastewater. Hexavalent chromium Cr(VI) is one of the metal ions in wastewater that has received considerable attention because of its toxicity. Chitosan was used in this study as the polymer to bind Cr(VI) to enhance its removal by ultrafiltration. The effects of chitosan-to-Cr(VI) ratio on Cr(VI) rejection and permeate flux were investigated. In addition, the fouling tendency was evaluated. Results showed that the addition of chitosan with a mass ratio of 12.5 increased the Cr (VI) rejection from …

Tuning Electrochemical Interactions And Polymer Electrolyte Interfaces For Enhanced Organic Acid Separations Using Electrodeionization, Matthew Leo Jordan

LSU Doctoral Dissertations

Chemical separations are critical processes for chemical and industrial plants to purify and isolate products however current separation technologies, such as distillation, rely on energy intensive processes. Electrochemical separation processes, such as electrodialysis and electrodeionization, are an energy efficient alternative that are emerging as an alternative for thermal-based separations. Organic acids are weakly ionizable species and susceptible for purification from process streams using electrochemical processes. Recently the fermentation route has garnered greater attention as a means for producing value-added chemicals, such as organic acids, from a renewable feedstock and aiding the circular economy. Some of the challenges electrodialysis faces for …

Design And Control Of Intensified Membrane Reactor Systems Through Module-Based Design Approach, Brent Bishop

Graduate Theses, Dissertations, and Problem Reports

As interest in the modularization and intensification of chemical processes continues to grow, more research must be directed towards the modeling and analysis of intensified process units. Intensified process units such as membrane reactors pose unique challenges pertaining to design and operation that have not been fully addressed in the reported literature. This work aims to address the design and control challenges caused by the integration of phenomena and the loss of degrees of freedom (DOF) that occur in the intensification of modular membrane reactor units.

First, a novel first-principles approach for modeling membrane reactors is developed using the AVEVA …

Water Recovery From Bioreactor Mixed Liquors Using Forward Osmosis With Polyelectrolyte Draw Solutions, Calen Raulerson

All Theses

The objective of this research was to test the feasibility of using forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. When combined with an Anaerobic Osmotic Membrane Bioreactor (AnOMBR), such a system could process fecal and food waste from astronauts aboard the International Space Station (ISS) and reclaim important nutrients and water. This project focused on measuring the obtainable water recovery rates from bioreactor effluent, and the identifying challenges associated with the operation.

AnOMBRs feature several advantages over aerobic bioreactors, and non-osmotic anaerobic membrane bioreactors (AnMBR). Anaerobic bioreactors avoid the significant energy costs of …

Atomically Thin Nanoporous Graphene Membranes For Fluid Separation, Anika O. K. Wong

Electronic Thesis and Dissertation Repository

Membrane separation applications such as water desalination and carbon capture require high permeance and selectivity. For such processes, nanoporous graphene membranes promise 100-fold higher permeance at comparable selectivity to conventional polymer membranes, but remain under development. This thesis reports fluid permeance through both simulated and experimental graphene nanopores. Molecular dynamics simulations were performed to investigate liquid advection-diffusion through graphene nanopores and how the transport rates differ from continuum predictions. Furthermore, a technique for measuring the gas permeance of nanoscopic areas of graphene was developed. Here, a single layer of graphene seals a ~10 nm diameter hole in a multi-layer graphene …

Inherently Porous Atomically Thin Membranes For Gas Separation, Harpreet Atwal

Electronic Thesis and Dissertation Repository

Membranes made from atomically thin materials promise hundreds of times higher production rates than conventional polymer membranes for separation applications. Graphene is impermeable to gases but becomes selectively permeable once pores are introduced into it but creating trillions of nanopores over large areas is difficult. By instead choosing an inherently porous two-dimensional material with naturally identical pores repeated at high density, we may circumvent this challenge. In this work, we explore the potential of two candidate materials, 2D polyphenylene and graphdiyne. We synthesize cyclohexane-m-phenylene, a monomer of 2D polyphenylene. We then develop an atomic force microscopy technique for measuring the …

Characterization Techniques And Cation Exchange Membrane For Non-Aqueous Redox Flow Battery, Kun Lou

Doctoral Dissertations

The motivation of this work comes from one of the major problems of emerging non-aqueous flow battery (NAFB) that a separator or membrane which facilitates conductivity and blocks redox species crossover does not exist. Although many aspects of principles can be mirrored from mature fuel cell and aqueous flow battery, it is found that some well-defined membrane properties in aqueous systems such as swelling, transport and interactions are different in non-aqueous solvents to some extent. However, the approach of this work does follow the way perfluorosulfonate ion exchange membrane (PFSA) facilitated development of fuel cell and aqueous flow battery in …

Simulation Of Water Loading In Filter Medium, Anthony Mole

Williams Honors College, Honors Research Projects

This research will model fluid flow through a filter plugged with water droplets using FlexPDE software. After simulations are run at various initial conditions, curves will be developed to correlate the permeability of the filter to variables like water droplet distribution and size.

Understanding Absorption, Supersaturation, And Drug Activity In Solution: Working Towards Developing A More Biorelevant Media, Freddy Arce

Theses and Dissertations--Pharmacy

With the looming dominance of poorly water-soluble chemical entities within the pharmaceutical pipeline, the pharmaceutical industry has leaned on the use of supersaturating drug delivery systems (SDDSs) to achieve efficacious concentrations within the gastrointestinal fluids. SDDSs aim to achieve concentrations in solutions greater than the solubility of the lowest energy crystalline form. However, the generation of supersaturated solutions of active pharmaceutical ingredients (APIs) creates a strong crystallization potential, which is undesirable.

In product development, supersaturating products often fail in Phase I and Phase II clinical trials due to poor oral bioavailability and a lack of in vivo efficacy. Pre-clinical testing …

Assessing The Impact Of Block-Selective Homopolymers On The Diffusion Of Payload Through Polymeric Organogels, Ian Coates

Honors Theses

Styrenic polymer gels have received recent attention for their application in transdermal patches due to their unique properties. Previous research in the pharmaceutical industry has identified that polymeric gels, specifically styrenic gels, have the potential to encompass multiple functions of the transdermal delivery patch including controlling mechanical and delivery properties. To tailor styrenic gels either the gel nanostructure or the drug complex can be controlled. Specifically, this thesis investigated the effect of gel nanostructure in an attempt to control the gel diffusivity and mechanical properties. To control gel nanostructure a phase selective styrene homopolymer was used at varying concentrations. It …

Optimizing Membrane Distillation With Solar Thermal Collectors, Andrew Mason, Ben Shulders, Siamak Nejati

UCARE Research Products

With rising human populations, the demand for freshwater is an ever-growing problem. One emerging technology to combat this problem is membrane distillation (MD). MD has several advantages for water desalination including 100% rejection of solute (salt, heavy metals, etc.) and mergeability with other affordable energy sources (solar heat, electric resistance, etc.) However, at the moment the specific energy consumption (SEC) of MD is very high due to low water production rates and large energy inputs to heat water. In a solar‐assisted design for MD, the high cost of solar collectors (~$200/m2) inhibits the low cost of water production in comparison …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Towards Efficient Water Treatment: Mechanism Of Colloidal Fouling Of Ultrafiltration Membranes, Ikenna Henry Ozofor

Dissertations, Master's Theses and Master's Reports

This research study first reviewed challenges of conventional and membrane separation systems for water treatment. Though membrane separation systems appeared superior to the conventional counterparts for water and wastewater treatment, wider applications of membrane systems have been limited by some factors, most notably is membrane fouling. Experimental studies were therefore conducted to achieve the goal of this research, which is to investigate how feed properties affect fouling of ultrafiltration (UF) membranes by colloids.

Feed salinity, pH, and nanoparticle concentration were the variables studied to unravel how different UF membranes are fouled by model silica colloids (with average diameter of 25nm). …

Applications Of Ionic Liquids In Membrane Separation, Mohanad Kamaz

Graduate Theses and Dissertations

Ionic liquids represent an emerging attractive material in membrane technology. The central theme of this doctoral dissertation is to develope novel membranes using ionic liquids. Two different approaches were used to prepare ionic liquid membranes including the immobilization of ionic liquid within the membrane pores or the use of pressure assembly method to deposit a selective ionic liquid layer on the top membrane surface.

In chapter 2, imidazolium ionic liquids with three different alkyl halides were successfully synthesized and used to prepare supported ionic liquid membranes (SILMs). SILMs preraper were tested for aqueous and nonaqueous applications. For nonaqueous applications, the …

Chemical And Physical Modification Of Thiol-Ene And Epoxy-Amine Networks For Advanced Control Of Gas Transport And Flame Retardant Behavior, Vivek Vasagar

Dissertations

Crosslinked polymers are widely used due to its several advantages not limited to high mechanical strength combined with the easy processability. Despite of its popular usage, the fundamental understanding of polymer structure affecting the desired properties is still lacking. This PhD thesis is in two parts, the first part is devoted to the design and developing a basic understanding of structure and chemical composition dependencies of gas transport, whereas in the second part a fundamental relationship between structure to the fire-retardant properties is established.

Membrane based gas separation technique has attracted interest of selective removal of carbon dioxide gas from …

Synthesis And Molecular Transport Studies In Zeolites And Nanoporous Membranes, Vivek Vattipalli

Doctoral Dissertations

The advent of nanoporous materials such as zeolites and nanoporous membranes has provided cost-effective solutions to some of the most pressing problems of the 20^th century such as the conversion of crude oil into fuels and valuable chemicals. Hierarchical zeolites and mesoporous inorganic membranes are showing great promise in addressing new problems such as the conversion of biomass into value-added chemicals and development of energy-efficient separation processes. The synthesis and fundamental aspects of molecular transport in these new materials with hierarchical porosities need to be better understood in order to rationally develop them for these desired applications. Pore narrowing …

Synthesis, Functionalization, And Application Of Nanofiltration And Composite Membranes For Selective Separations, Andrew Steven Colburn

Theses and Dissertations--Chemical and Materials Engineering

Future nanofiltration (NF) membranes used for selective separations of ions and small organic molecules must maintain performance in environments where high concentrations of total dissolved solvents or foulants are present. These challenges can be addressed through the development of composite membranes, as well as the engineering of enhanced surface properties and operating conditions for existing commercial membranes.

In this work, ion transport through commercial thin film composite (TFC) polyamide NF membranes were studied in both lab-prepared salt solutions and industrial wastewater. The dependence of several variables on ion rejection was investigated, including ion radius, ion charge, ionic strength, and temperature. …

Synthesis, Characterization And Applications Of Reduced Graphene Oxide And Composite Membranes For Selective Separations And Removal Of Organic Contaminants, Ashish Aher

Theses and Dissertations--Chemical and Materials Engineering

Among the next generation materials being investigated for membrane development, partially reduced Graphene Oxide (rGO) has received increasing attention from the membrane community. rGO-based nanofiltration membranes have shown promising results in applications such as partial desalination, organic contaminant removal, gas-phase separations, and separations from solvent media. rGO offers a unique platform compared to common polymeric membranes since it can be used for separation applications in both aqueous and organic solvent media. An rGO-based platform could also be utilized to synthesize reactive membranes, giving rGO membranes the additional capability of reactively removing organic contaminants. This research focuses on the synthesis of …

Capillary Forces In Partially Saturated Thin Fibrous Media, Ali Moghadam

Theses and Dissertations

Capillarity is often exploited in self-cleaning, drag reducing and fluid absorption/storage (sanitary products) purposes just to name a few. Formulating the underlying physics of capillarity helps future design and development of optimized structures. This work reports on developing computational models to quantify the capillary pressure and capillary forces on the fibrous surfaces. To this end, the current study utilizes a novel mass-spring-damper approach to incorporate the mechanical properties of the fibers in generating virtual fibrous structures that can best represent fibrous membranes. Such virtual fibrous structures are then subjected to a pressure estimation model, developed for the first time in …

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

Transport Of Water And Ions Through Single-Walled Armchair Carbon Nanotubes: A Molecular Dynamics Study, Michelle Patricia Aranha

Doctoral Dissertations

The narrow hydrophobic interior of a carbon nanotube (CNT) poses a barrier to the transport of water and ions, and yet, unexpectedly, numerous experimental and simulation studies have confirmed fast water transport rates comparable to those seen in biological aquaporin channels. These outstanding features of high water permeability and high solute rejection of even dissolved ions that would typically require a lot of energy for separation in commercial processes makes carbon nanotubes an exciting candidate for desalination membranes. Extending ion exclusion beyond simple mechanical sieving by the inclusion of electrostatics via added functionality to the nanotube bears promise to not …

Microbial Desalination Cells With Efficient Platinum Group Metal-Free Cathode Catalysts, Morteza Rezaei Talarposhti

Chemical and Biological Engineering ETDs

Iron-nitrogen-carbon based catalyst was used at the cathode of a microbial desalination cell (MDC) and compared with platinum (Pt) and activated carbon (AC) cathode. Fe-N-C catalyst was prepared using nicarbazin (NCB) as organic precursor by sacrificial support method (SSM). Rotating ring disk electrode (RRDE) experiments shows that Fe-NCB had higher electrocatalytic activity compared to AC and Pt. The utilization of Fe-NCB into the cathode improved substantially the performance output with initial maximum power density of 49±2 μWcm^-2 in contrast to Pt and AC catalysts which have shown lower values of 34±1 μWcm^-2 and 23.5±1.5 μWcm^-2, respectively. …

Modeling Of Nanoscale Transport In Mesoporous Membranes, Ashutosh Rathi

Doctoral Dissertations

Mesoporous membranes with pore sizes in the range 2-50 nm provide an energy efficient alternative for separation of mixtures such as CO₂ from stack effluents and volatile organic compounds (VOC) from air. Transport mechanisms such as capillary condensation, Knudsen diffusion and surface adsorption help in enrichment of a more condensable component based on the bulk mixture thermodynamics, surface chemistry and geometry of the mesopores. Despite the progress in synthesis techniques, design of better mesoporous materials for targeted separations is still a challenge due to the absence of clear design rules. Modeling techniques can be used to quantify the relevant …

Hybrid Polymer Electrolyte For Lithium-Oxygen Battery Application, Amir Chamaani

FIU Electronic Theses and Dissertations

The transition from fossil fuels to renewable resources has created more demand for energy storage devices. Lithium-oxygen (Li-O₂) batteries have attracted much attention due to their high theoretical energy densities. They, however, are still in their infancy and several fundamental challenges remain to be addressed. Advanced analytical techniques have revealed that all components of a Li-O₂ battery undergo undesirable degradation during discharge/charge cycling, contributing to reduced cyclability. Despite many attempts to minimize the anode and cathode degradation, the electrolyte remains as the leading cause for rapid capacity fading and poor cyclability in Li-O₂ batteries. In this …

Pore-Confined Carriers And Biomolecules In Mesoporous Silica For Biomimetic Separation And Targeting, Shanshan Zhou

Theses and Dissertations--Chemical and Materials Engineering

Selectively permeable biological membranes composed of lipophilic barriers inspire the design of biomimetic carrier-mediated membranes for aqueous solute separation. This work imparts selective permeability to lipid-filled pores of silica thin film composite membranes using carrier molecules that reside in the lipophilic self-assemblies. The lipids confined inside the pores of silica are proven to be a more effective barrier than bilayers formed on the porous surface through vesicle fusion, which is critical for quantifying the function of an immobilized carrier. The ability of a lipophilic carrier embedded in the lipid bilayer to reversibly bind the target solute and transport it through …

Biopolymer Electrospun Nanofiber Mats To Inactivate And Remove Bacteria, Katrina Ann Rieger

Doctoral Dissertations

The persistence of antibiotic resistance in bacterial pathogens remains a primary concern for immunocompromised and critically-ill hospital patients. Hospital associated infections can be deadly and reduce the successes of medical advancements, such as, cancer therapies and medical implants. Thus, it is imperative to develop materials that can (i) deliver new antibiotics with accuracy, as well as (ii) uptake pathogenic microbes. In this work, we will demonstrate that electrospun nanofiber mats offer a promising platform for both of these objectives because of their high surface-to-volume ratio, interconnected high porosity, gas permeability, and ability to contour to virtually any surface. To provide …

Synthesis And Characterization Of Polymeric Anion Exchange Membranes, Wenxu Zhang

Doctoral Dissertations

As alkaline anion exchange membrane fuel cells (AAEMFC) are regarded as promising and important energy devices, the development of high performance anion exchange membranes are in urgent need, as well as fundamental investigation on the structure-property relationship, which are the motivation of this dissertation. Three different polymer systems are presented and focused on polymer synthesis, material morphology, and ion transport phenomena. Crosslinked membranes are promising as practical materials, however, the understanding and further improvement of its performance is hindered by the lack of an ordered morphology or well-defined chemical structure. In Chapter 2, a series of crosslinked membranes were design …