Biomedical Engineering and Bioengineering Commons^™

Kinematic Analysis Of Gait And Deep Knee Flexion For Pre- And Post-Operative Total Knee Arthroplasty, Samantha Collins

Electronic Theses and Dissertations

Osteoarthritis (OA) is a form of arthritis that develops in the joint due to overuse and aging causing pain, discomfort, and disability. Total Knee Arthroplasty (TKA) is a surgical procedure performed when OA symptoms are severe with an estimated 600,000 patients in the United States currently receiving TKA. Studies have reported dissatisfaction of the knee for 14-39% of patients. This study collected knee kinematics before and after surgery using stereo radiography for precise measurement of gait and deep knee flexion activities. Results showed healthy knee kinematics were not restored and no significant changes could be seen from OA kinematics in …

Revision Total Hip Femoral Stem Micromotion And Statistical Shape Modeling Of The Knee, William Fugit

Electronic Theses and Dissertations

The first purpose of this thesis was to compare the amount of micromotion seen in the femoral stem in a revision total hip arthroplasty between simple loading conditions and loading conditions derived from activities of daily living, through the use of experimental and computational methods. The amount of micromotion at the bone-implant interface was larger for activities of daily living, with ranges of 200μm more than the largest simple loading conditions. The second purpose of this thesis was to compare measurements of accuracy in a statistical shape model between individual bone and joint-level models, specifically for the knee. Using computational …

Tibial Strains And Tray-Bone Micromotions After Total Knee Arthroplasty: Computational Studies Evaluating The Tibial Fixation, Huizhou Yang

Electronic Theses and Dissertations

Cemented and cementless fixation in total knee arthroplasty (TKA) have been successfully used for decades. As the number of younger and more active patients treated with TKA continues to increase, long-term implant survivorship is of increasing importance. One of the most common complications and hence the reason for revision is mechanical loosening (23.1% of all revised TKA). The loosening mechanisms have been proposed for different fixation types. For cemented fixation, bone remodeling after surgery is regulated by the changes in strain energy density (SED). The recruitment of osteoclasts and osteoblasts is controlled by SED-related signals. Insufficient stimuli can promote bone …

An Accuracy And Precision Analysis Of The Velys™ Robotic Assisted Solution For Total Knee Arthroplasty, Gary Doan

Electronic Theses and Dissertations

Total knee arthroplasty (TKA) is a procedure where the arthritic surfaces of the knee is removed and replaced with a combination of metal and polymer implants that recreates the joint line to restore function and quality of life. Implant alignment is important in the success of a TKA. Modern day conventional instrumentation can be cumbersome in the operating room and can be inaccurate when resecting bone and aligning implants. Patients with large errors in resections and implant orientation are more prone to experience mechanical failures with their TKA. Mechanical failures in primary TKA require revision surgeries which can lead to …

Development Of An Active Infection Monitoring Knee Spacer For Two-Stage Revision, Michael K. Lavdas

Electronic Thesis and Dissertation Repository

Infections requiring surgical revision occur in ~3% of total knee arthroplasty (TKA) procedures. The standard treatment for TKA infection in North America is referred to as the two-stage revision process. Unfortunately, the success rate of the two-stage revision is low, at roughly 85%. There are indications that the two-stage revision may fail to clear the infection due to unsatisfactory diagnostic tools. This thesis depicts the development and evaluation of a novel telemetric sensing package designed for integration into the two-stage revision process. Studies within evaluate its performance through sensor validation, thermal insulation testing, radio frequency penetration evaluation, a cadaveric loading …

Development Of A Statistical Shape-Function Model Of The Implanted Knee For Real-Time Prediction Of Joint Mechanics, Kalin Gibbons

Boise State University Theses and Dissertations

Outcomes of total knee arthroplasty (TKA) are dependent on surgical technique, patient variability, and implant design. Non-optimal design or alignment choices may result in undesirable contact mechanics and joint kinematics, including poor joint alignment, instability, and reduced range of motion. Implant design and surgical alignment are modifiable factors with potential to improve patient outcomes, and there is a need for robust implant designs that can accommodate patient variability. Our objective was to develop a statistical shape-function model (SFM) of a posterior stabilized implant knee to instantaneously predict output mechanics in an efficient manner. Finite element methods were combined with Latin …

Polymeric Microsensors For Intraoperative Contact Pressure Measurement, Emily R. Pritchard

Doctoral Dissertations

Biocompatible sensors have been demonstrated using traditional microfabrication techniques modified for polymer substrates and utilize only materials suitable for implantation or bodily contact. Sensor arrays for the measurement of the load condition of polyethylene spacers in the total knee arthroplasty (TKA) prosthesis have been developed. Arrays of capacitive sensors are used to determine the three-dimensional strain within the polyethylene prosthesis component. Data from these sensors can be used to give researchers a better understanding of component motion, loading, and wear phenomena for a large range of activities. This dissertation demonstrates both analytically and experimentally the fabrication of these sensor arrays …

Stereoscopic Analysis Of Trabecular Bone Orientation In Proximal Human Tibias, K. N. Bachus, M. K. Harman, R. D. Bloebaum

Cells and Materials

The three-dimensional orientation of trabeculae is a key factor in determining the load carrying capabilities of cancellous bone. Previous biomechanical studies have shown that proximal tibias resected parallel to the articulating surface are stronger and stiffer than the contralateral tibias resected perpendicular to the long axis of the bone. However, morphologic evidence was not provided to help explain the mechanical differences.

To determine the orientation of the trabeculae in the medial condyle for both parallel cut and perpendicular cut specimens, a scanning electron microscope and stereoscopic techniques were used. Data showed that tibias cut parallel to the articular surface had …