Biomedical Engineering and Bioengineering Commons^™

Biomechanical Tolerance Of Whole Lumbar Spines In Straightened Posture Subjected To Axial Acceleration, Brian D. Stemper, Sajal Chirvi, Ninh Doan, Jamie L. Baisden, Dennis J. Maiman, William H. Curry, Narayan Yoganandan, Frank A. Pintar, Glenn Paskoff, Barry S. Shender

Biomedical Engineering Faculty Research and Publications

Quantification of biomechanical tolerance is necessary for injury prediction and protection of vehicular occupants. This study experimentally quantified lumbar spine axial tolerance during accelerative environments simulating a variety of military and civilian scenarios. Intact human lumbar spines (T12‐L5) were dynamically loaded using a custom‐built drop tower. Twenty‐three specimens were tested at sub‐failure and failure levels consisting of peak axial forces between 2.6 and 7.9 kN and corresponding peak accelerations between 7 and 57 g. Military aircraft ejection and helicopter crashes fall within these high axial acceleration ranges. Testing was stopped following injury detection. Both peak force and acceleration were significant …

Brain Motion, Deformation, And Potential Injury During Soccer Heading, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Working Papers

This paper addresses the problem of what is happening physically inside the skull during head-ball contact. Mathematical models based upon Newton’s laws of motion and numerical methods are used to create animations of brain motion and deformation inside the skull.

Initially a 1 cm gap filled with cerebrospinal fluid (CSF) separates the brain from the rigid skull in adults and older children. Whole head acceleration induces a pulse of artificial gravity within the skull. Because brain density differs slightly from that of CSF, the brain accelerates and strikes the inner aspect of the skull, undergoing viscoelastic deformation, ranging from 1 …

Sagittal Subtalar And Talocrural Joint Assessment During Ambulation With Controlled Ankle Movement (Cam) Boots, Ben Mchenry, Emily L. Exten, Janelle A. Cross, Karen M. Kruger, Brian Law, Jessica M. Fritz, Gerald F. Harris

Biomedical Engineering Faculty Research and Publications

Background: The purpose of the current study was to determine sagittal plane talocrural and subtalar kinematic differences between barefoot and controlled ankle movement (CAM) boot walking. This study used fluoroscopic images to determine talar motion relative to tibia and calcaneal motion relative to talus.

Methods: Fourteen male subjects (mean age 24.1 ± 3.5 years) screened for normal gait were tested. A fluoroscopy unit was used to collect images at 200 Hz during stance. Sagittal motion of the talocrural and subtalar joints were analyzed barefoot and within short and tall CAM boots.

Results: Barefoot talocrural mean maximum plantar and dorsiflexion were …

Biomechanics Of Snoring And Sleep Apnea, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Working Papers

To understand the mechanisms of snoring and sleep apnea a first-principles biomechanical analysis was done for airflow through branched parallel channels, separated by a freely movable soft palate, and converging to a common channel at the base of the tongue in a “Y-shaped” configuration. Branches of the Y describe slit-like passages on the nasal and oral sides of the soft palate, when the palate is pushed by backward movement of the tongue to form a wedge between the tongue surface and the posterior pharyngeal wall. The common channel of the Y describes the oropharyngeal passage between the base of the …

Biplane Fluoroscopy For Hindfoot Motion Analysis During Gait: A Model-Based Evaluation, Janelle A. Cross, Ben Mchenry, Robert C. Molthen, Emily Exten, Taly Gilat-Schmidt, Gerald F. Harris

Biomedical Engineering Faculty Research and Publications

The purpose of this study was to quantify the accuracy and precision of a biplane fluoroscopy system for model-based tracking of in vivo hindfoot motion during over-ground gait. Gait was simulated by manually manipulating a cadaver foot specimen through a biplane fluoroscopy system attached to a walkway. Three 1.6-mm diameter steel beads were implanted into the specimen to provide marker-based tracking measurements for comparison to model-based tracking. A CT scan was acquired to define a gold standard of implanted bead positions and to create 3D models for model-based tracking. Static and dynamic trials manipulating the specimen through the capture volume …

The Biomechanics Of Music Performance, Rachel F. Bellisle, Jessika Decker

Senior Honors Projects

When first learning to play a wind instrument, beginner musicians are taught how to hold their instrument and correctly position their body. They are taught how to sit, where to put their hands and fingers on the keys, and how to hold their arms. This initial lesson on posture and hand positioning is often short, as one quickly moves on to learn the embouchure and breathing techniques that allow sound to be produced. As a musician progresses in skill, positioning is emphasized more, and they learn that it can affect their risk of strain or injury and improve their sound …