Automotive Engineering Commons^™

Control Of Mr Damper Using Anfis And Pid Controller For Optimum Vehicle Ride Comfort, Mohammad Faisal Yakhni, Mohamad Ali, Mohamed El-Gohary

BAU Journal - Science and Technology

Suspension system design is an important challenging duty that facing car manufacturers, so the challenge has become to design the best system in terms of providing ride comfort and handling ability under all driving situations. The goal of this paper is to provide assistance in enhancing the effectiveness of the suspension system. A full car model with eight Degrees Of Freedom (DOF) was developed using MATLAB/Simulink. Validation of the Simulink model was obtained. The model was assumed to travel over a speed hump that has a half sine wave shape and amplitude that changing from 0.01 to 0.2 m. The …

A New Method Of Statcom Controlling For Harmonic Mitigation And Power Factor Correction, Doha Jdeed

Journal of the Arab American University مجلة الجامعة العربية الامريكية للبحوث

This paper presents a control algorithm of 3ph STATic synchronous COMpensator (STATCOM). The algorithm depends on the accurate reference currents extraction from only the nonlinear load current spec-trum in frequency domain using Fast Fourier Transfer (FFT). Then the determined harmonics and reactive components of load current are added together to form the compensating reference signals, the PI controllers then generate signals which control the Pulse Width Modulation (PWM) method. The simulation of the study is carried out under MATLAB/Simulink environment to show the usefulness of this control algorithm with nonlin-ear dynamic loads. It determines exactly the phase shift between the …

Photovoltaics- And Battery-Based Power Network As Sustainable Source Of Electric Power, Prahaladh Paniyil, Vishwas Powar, Rajendra Singh, Benjamin Hennigan, Pamela Lule, Matthew Allison, John Kimsey, Anthony Carambia, Dhruval Patel, Daniel Carrillo, Zachary Shriber, Truman Bazer, James Farnum, Kushal Jadhav, Dalton Pumputis

Publications

With the rise in the utilization of free fuel energy sources, namely solar and wind, across the globe, it has become necessary to study and implement models of a sustainable power network. This paper focuses on the design of a conceptual power network based on photovoltaics (PV) for power generation and lithium-ion batteries for storage. The power system showcases the various metrics that are involved in a grid-tied PV- and battery-based power network. It also encompasses the various design parameters and sizing considerations to design and conceptualize such a power network. The model focuses on the importance of the conservation …

Turbulence Investigations In The Core-Flow Of An Internal Combustion Engine, James R. Macdonald

Dissertations

Turbulence significantly impacts the operation of energy conversion devices. In internal combustion (IC) engines, mixing, heat transfer, and combustion are all strongly dependent on the turbulence inside the cylinder. Consequently, knowledge of the state of turbulence is critical for improving our understanding and modeling of engine processes.

Turbulence states may be determined through analysis of the Reynolds stress tensor, which can in turn be experimentally quantified using velocity data. In this research, stereoscopic particle image velocimetry (stereo-PIV) experiments were conducted in a single-cylinder, motored engine with optical access to measure the two-dimensional, three-component (2D-3C) velocity fields throughout the compression stroke. …

Control And Locomotion Of Inertially And Magnetically Actuated Multi-Scale Robotic Systems, Ehab Al Khatib

Mechanical Engineering Research Theses and Dissertations

In this research, two actuation systems were introduced, inertial and magnetic actuation. In the inertial actuation, the robot used the transfer of momentum to navigate, and this momentum could be generated by spinning masses and wheels. Recent studies in our System Laboratory proved that a wide range of inertially actuated locomotion systems could be generated. This can be achieved by using a family tree approach, starting from a very simple system, and progressively evolving it to more complex ones. The motion diversity of these robots inspired us to extend their locomotion from a macro scale to millimeter and micro scales. …

Basic Utilities Vehicle (Buv) Milk Transportation, Brian D. Reynolds, Sean Patrick Bayless Galligar, Emmitt Hanner, Joshua T. Pitts

Scholar Week 2016 - present

In developing countries, a need exists for the transportation of raw foods to communities without spoilage. Traditional methods of transporting goods don’t meet the needs of the consumer, and often times food is wasted due to the harsh climate and time constraints. Food often becomes salvage under the heat, causing a hurt to the profitability of vendors and family needs for fresh produce. In particular milk transportation has become difficult, due to the lack of cold storage in standard transit. As a response to the need for affordable raw food transport, our sponsor Basic Utilities Vehicle (BUV) has tasked us …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …

Comparison Of Optimal Energy Management Strategies Using Dynamic Programming, Model Predictive Control, And Constant Velocity Prediction, Amol Arvind Patil

Masters Theses

Due to the recent advancements in autonomous vehicle technology, future vehicle velocity predictions are becoming more robust which allows fuel economy (FE) improvements in hybrid electric vehicles through optimal energy management strategies (EMS). A real-world highway drive cycle (DC) and a controls-oriented 2017 Toyota Prius Prime model are used to study potential FE improvements. We proposed three important metrics for comparison: (1) perfect full drive cycle prediction using dynamic programming, (2) 10-second prediction horizon model predictive control (MPC), and (3) 10-second constant velocity prediction. These different velocity predictions are put into an optimal EMS derivation algorithm to derive optimal engine …

Internal Combustion Engine, Philippe D. Habets, Sam S. Flood, Paing Htet Lin, Jason Wu, Ricardo Cuevas

Mechanical Engineering

The goal of this project is to modify a Honda GX35 engine to improve its fuel efficiency and maximize its competitiveness in the Shell Eco-marathon competitions. This competition has tight restrictions on the type of fuel used to power the engine, but otherwise has very few rules limiting the type of modifications which may be made. Our primary goals are to maximize volumetric efficiency and maintain an efficient operating temperature. Future work might pursue more advanced technologies such as pseudo-atkinson cycle operation.

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

Electrathon Vehicle: Front Suspension, Christopher Clark

All Undergraduate Projects

Central Washington University does not currently have a competition field-able Electrathon America electric vehicle with adequate front suspension. The aim of this project was to provide the vehicle with handling that supports sound ground contact throughout the competition environment. Handling that supports sound ground contact is important for vehicles so they can go around corners without a loss of traction or flipping over. The solution to this engineering problem was designed and tested through various requirements. The requirements at hand were that the suspension components weigh less than 50 pounds, that there be no more than 3 inches of suspension …

Sensor Fusion And Non-Linear Mpc Controller Development Studies For Intelligent Autonomous Vehicular Systems, Ahammad Basha Dudekula

Dissertations, Master's Theses and Master's Reports

The demand for safety and fuel efficiency on ground vehicles and advancement in embedded systems created the opportunity to develop Autonomous controller. The present thesis work is three fold and it encompasses all elements that are required to prototype the autonomous intelligent system including simulation, state handling and real time implementation. The Autonomous vehicle operation is mainly dependent upon accurate state estimation and thus a major concern of implementing the autonomous navigation is obtaining robust and accurate data from sensors. This is especially true, in case of Inertial Measurement Unit (IMU) sensor data. The IMU consists of a 3-axis gyro, …

Human Powered Vehicle Internal Systems Design, Zachary Broadbent, Jordan Boos, Patrick Gaertner, Caleb Miner

Williams Honors College, Honors Research Projects

The objective of this design project is to redesign the seat and steering system for the Human Powered Vehicle Team. The goal of the seat design is too improve ergonomics by making it more comfortable and adjustable. In making the seat adjustable, it will be easier for drivers to achieve an optimal efficiency when pedaling. The aim for steering will be to improve the ergonomics as well as performance by analyzing steering systems in the past and evaluating how each design was successful and for what reason. Another main goal of the steering system will be improving the stability and …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Design Of An Anti-Jerk Controller For Both Locked And Slipping Torque Converter Conditions In A Vehicle, Syed Ahmad Nadeem

Dissertations, Master's Theses and Master's Reports

With the advancement in the automotive technologies, the customer scrutiny on the ride comfort of automobiles has come to light. Vehicle drivability is one of the important aspects that defines the ride comfort for a vehicle. Drivability of a vehicle is a qualitative measure and may differ from person to person, however, researches have come up to highlight a few parameters that can categorize the drivability performance of a vehicle into good or bad for a majority of the targeted audience. One of those parameters include shuffle, which is defined as the longitudinal oscillations that occurs in the drivetrain when …

A Study Of Model-Based Control Strategy For A Gasoline Turbocharged Direct Injection Spark Ignited Engine, Xin Wang

Dissertations, Master's Theses and Master's Reports

To meet increasingly stringent fuel economy and emissions legislation, more advanced technologies have been added to spark-ignition (SI) engines, thus exponentially increase the complexity and calibration work of traditional map-based engine control. To achieve better engine performance without introducing significant calibration efforts and make the developed control system easily adapt to future engines upgrades and designs, this research proposes a model-based optimal control system for cycle-by-cycle Gasoline Turbocharged Direct Injection (GTDI) SI engine control, which aims to deliver the requested torque output and operate the engine to achieve the best achievable fuel economy and minimum emission under wide range of …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Radio Frequency Studies Of Soot Loading And Ammonia Storage On A Diesel Particulate Filter With A Scr Catalyst Coating, Shreyans Sethia

Dissertations, Master's Theses and Master's Reports

The radio frequency (RF) measurement technique has been shown to be a viable method for measurement of the amount of soot loaded onto DPF’s ^[1] and the amount of NH₃ stored on SCR catalysts ^[2]. In one of the configurations, a microwave resonant cavity is formed by the metal can encasing the enclosed catalyst. Two metal probes acting as antennas are placed on either side of the catalyst. Power transmitted between the antennas is monitored as the frequency of the signal is swept. At certain frequencies, resonance is achieved. Measurements of the resonance frequencies, amplitude at resonance, and …

Measurement Of Current Distribution In The Land Channel Direction Of A Proton Exchange Membrane Fuel Cell, Chinmay Kulkarni

Dissertations, Master's Theses and Master's Reports

A fully functional proton exchange membrane fuel cell with single land channel geometry on the cathode and segmented anode current collector with 9 mm² active area with a 350μm spatial resolution was utilized to measure the local current distribution in the land channel direction. A distinguished printed circuit board approach was used for the data acquisition to adapt to any flow field design.

Performance of this segmented cell was examined at dry, wet and moderate humidity settings to study the water transport phenomenon in the PEMFC. In the dry condition at 60 ͦ C with 0% relative humidity, the …

Filtered-Dynamic-Inversion Control For Unknown Minimum-Phase Systems With Unknown Relative Degree, Sumit Suryakant Kamat

Theses and Dissertations--Mechanical Engineering

We present filtered-dynamic-inversion (FDI) control for unknown linear time-invariant systems that are multi-input multi-output and minimum phase with unknown-but-bounded relative degree. This FDI controller requires limited model information, specifically, knowledge of an upper bound on the relative degree and knowledge of the first nonzero Markov parameter. The FDI controller is a single-parameter high-parameter-stabilizing controller that is robust to uncertainty in the relative degree. We characterize the stability of the closed-loop system. We present numerical examples, where the FDI controller is implemented in feedback with mathematical and physical systems. The numerical examples demonstrate that the FDI controller for unknown relative degree …

Numerical Analyses And Integration Of Split Lot Sizing Using Lean Benchmark Model For Small Lot Manufacturing In High Mix Low Volume Production, Omkar Bhosale

Theses and Dissertations--Manufacturing Systems Engineering

As the global demand for automobiles has increased rapidly over the last fifty years, customers have become more particular about the characteristics of the autos they want. This change in demand, in part has pushed manufacturing to become more flexible and created a demand for alternative, more efficient processes like the High Mix Low Volume (HMLV) production of vehicles. During HMLV, manufacturers create production lot sizes and schedule to synchronize the production processes to meet customer demand on time. The demand for the automobile parts may not be uniform or parts may not be consumed by the customer immediately, Due …

Implementation Of Radial Basis Function Artificial Neural Network Into An Adaptive Equivalent Consumption Minimization Strategy For Optimized Control Of A Hybrid Electric Vehicle, Thomas P. Harris

Graduate Theses, Dissertations, and Problem Reports

Continued increases in the emission of greenhouse gases by passenger vehicles has accelerated the production of hybrid electric vehicles. With this increase in production, there has been a parallel demand for continuously improving strategies of hybrid electric vehicle control. The goal of an ideal control strategy is to maximize fuel economy while minimizing emissions. The design and implementation of an optimized control strategy is a complex challenge. Methods exist by which the globally optimal control strategy may be found. However, these methods are not applicable in real-world driving applications since these methods require a priori knowledge of the upcoming drive …

Route Planning For Long-Term Robotics Missions, Christopher Alexander Arend Tatsch

Graduate Theses, Dissertations, and Problem Reports

Many future robotic applications such as the operation in large uncertain environment depend on a more autonomous robot. The robotics long term autonomy presents challenges on how to plan and schedule goal locations across multiple days of mission duration. This is an NP-hard problem that is infeasible to solve for an optimal solution due to the large number of vertices to visit. In some cases the robot hardware constraints also adds the requirement to return to a charging station multiple times in a long term mission. The uncertainties in the robot model and environment require the robot planner to account …

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Autonomous Guided Vehicle Frame For Outdoor Use, Thomas Mcgrath

Williams Honors College, Honors Research Projects

The overall goal for my project is to design a durable Autonomous Guided Vehicle (AGV) frame intended for carrying a heavy load over outdoor terrain. I will not be designing a complete vehicle, only the basic structure that can be used to build a complete AGV on. There will be complete 3D models of the design and its individual parts. I also would like to provide limited Finite Element Analysis of the design using ANSYS software to determine weaknesses and methods for improvement. The design I create is meant to be used as a framework for complete outdoor AGV designs. …

Piezoelectric Energy Harvester Improvement, Nathan Embaugh, Jason Mack, Jeremiah Fitzgerald, Zachary J. Lindsey

Williams Honors College, Honors Research Projects

The energy harvester is used to convert a portion of the tire deflection waste energy to power up tire embedded sensors. A piezoelectric energy harvester is designed and some preliminary tests are done on it. So far, it has been shown that this design is sufficient for tire application. The team will need to modify the design of the energy harvester, the measurement setup and add a temperature and a strain senor to the existing setup so that the tire deflection and temperature can be measured and at the same time the energy harvester should be tested to see how …