Aerodynamics and Fluid Mechanics Commons^™

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

Electronic Theses and Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Complicating Factors In Hydraulic Jumps: The Effects Of Earth's Rotation, Muveno Pascoal Elias Mucaza

Electronic Thesis and Dissertation Repository

Hydraulic jumps at the interface of stratified rotating fluids are studied. The flow is de- fined with continuous density and velocity profiles, with the velocity in each layer changing (upstream shear). The study is conducted in jumps defined by an imposed velocity transition, and jumps developing over a topography.

The numerical simulations conducted showed the qualitative structure of the flow changing in the cross-width direction, as well as the size and amount of turbulence of the jumps. Mixing in these jumps was shown to increase towards the side of the domain where the jumps were larger and more turbulent. The …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Considerations For The Design Optimization Of Floating Offshore Wind Turbine Blades, Evan M. Gaertner

Doctoral Dissertations

Floating offshore wind turbines are an immature technology with relatively high costs and risk associated with deployment. Of the few floating wind turbine prototypes and demonstration projects deployed in real metocean conditions, all have used standard turbines design for onshore or offshore fixed bottom conditions. This neglects the unique unsteady aerodynamics brought on by floating support structure motion. While the floating platform has been designed and optimized for a given rotor, the global system is suboptimal due to the rotor operating in conditions outside of which it was design for. If the potential offered by floating wind turbines is to …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Dynamic Response Of A Hingeless Helicopter Rotor Blade At Hovering And Forward Flights, Pratik Sarker

University of New Orleans Theses and Dissertations

The helicopter possesses the unrivaled capacity for vertical takeoff and landing which has made the helicopter suitable for numerous tasks such as carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. The nature of the aerodynamic environment surrounding the helicopter gives rise to a significant amount of vibration to its whole body. Among different sources of vibrations, the main rotor blade is the major contributor. The dynamic characteristics of the hingeless rotor consisting of elastic blades are of particular interest because of the strongly coupled equations of motion. The elastic rotor blades are subjected …

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Leading Edge Boundary Layer Suction Device For The Cal Poly Rolling Road Wind Tunnel, Daniel C. Glover, Liam M. Madden, Robert J. Cabri

Mechanical Engineering

Over the course of three quarters from Fall of 2016 to Spring of 2017, our team designed and built a boundary layer suction device. The boundary layer suction device has three main functions: a scoop that redirects most of the boundary layer air out of the wind tunnel, fans that suck the remaining boundary layer air through a porous plate and ducting and out of the wind tunnel, and a transition bridge that transitions the remaining air smoothly onto the rolling road. The wind tunnel is owned by Cal Poly and the rolling road is a new addition to it. …

Improving Predictive Capabilities Of Classical Cascade Theory For Nonproliferation Analysis, David Allen Vermillion

Doctoral Dissertations

Uranium enrichment finds a direct and indispensable function in both peaceful and nonpeaceful nuclear applications. Today, over 99% of enriched uranium is produced by gas centrifuge technology. With the international dissemination of the Zippe archetypal design in 1960 followed by the widespread illicit centrifuge trafficking efforts of the A.Q. Khan network, traditional barriers to enrichment technologies are no longer as effective as they once were. Consequently, gas centrifuge technology is now regarded as a high-priority nuclear proliferation threat, and the international nonproliferation community seeks new avenues to effectively and efficiently respond to this emergent threat.

Effective response first requires an …

Data-Driven Adaptive Reynolds-Averaged Navier-Stokes K - Ω Models For Turbulent Flow-Field Simulations, Zhiyong Li

Theses and Dissertations--Mechanical Engineering

The data-driven adaptive algorithms are explored as a means of increasing the accuracy of Reynolds-averaged turbulence models. This dissertation presents two new data-driven adaptive computational models for simulating turbulent flow, where partial-but-incomplete measurement data is available. These models automatically adjust (i.e., adapts) the closure coefficients of the Reynolds-averaged Navier-Stokes (RANS) k-ω turbulence equations to improve agreement between the simulated flow and a set of prescribed measurement data.

The first approach is the data-driven adaptive RANS k-ω (D-DARK) model. It is validated with three canonical flow geometries: pipe flow, the backward-facing step, and flow around an airfoil. For all 3 test …

Numerical Investigation Of Full Scale Thunderstorm Downbursts: A Parametric Study And Comparison To Meteorological Model, Christopher Oreskovic

Electronic Thesis and Dissertation Repository

A series of Large Eddy Simulations using an atmospheric meteorological cloud model have been used to investigate the important geometric and thermal parameters that influence a thunderstorm downburst outflow, as it pertains specifically to the idealized cooling source model. A separate set of Large Eddy Simulations make use of the same idealized cooling source model, in a realistic atmospheric base state using real field sounding data, in an attempt to make a quantifiable comparison to a downburst from a full cloud simulation. Randomness has been added to the cooling source forcing function to mimic the thermal variation in a real …

On The Selection Of A Good Shape Parameter For Rbf Approximation And Its Application For Solving Pdes, Lei-Hsin Kuo

Dissertations

Meshless methods utilizing Radial Basis Functions~(RBFs) are a numerical method that require no mesh connections within the computational domain. They are useful for solving numerous real-world engineering problems. Over the past decades, after the 1970s, several RBFs have been developed and successfully applied to recover unknown functions and to solve Partial Differential Equations (PDEs).
However, some RBFs, such as Multiquadratic (MQ), Gaussian (GA), and Matern functions, contain a free variable, the shape parameter, c. Because c exerts a strong influence on the accuracy of numerical solutions, much effort has been devoted to developing methods for determining shape parameters which provide …

Cfd Analysis Of Viscosity Effects On Turbine Flow Meter Performance And Calibration, Carl Tegtmeier

Masters Theses

In this research turbine flow meters were studied, using computational fluid dynamics (CFD) modeling to the study effects of viscosity on the flow meters, across a wide range of operation, to improve our understanding and their performance. A three-dimensional computational model was created for a typical flow meter geometry. The work began with a steady state model to provide an acceptable initial condition for further simulations. These results were input into a transient model that has a rotating zone around the rotor to provide insight into the interaction between static and rotational structures. In order to automatically adjust the rotor …

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Modeling Dynamic Stall For A Free Vortex Wake Model Of A Floating Offshore Wind Turbine, Evan M. Gaertner

Masters Theses

Floating offshore wind turbines in deep waters offer significant advantages to onshore and near-shore wind turbines. However, due to the motion of floating platforms in response to wind and wave loading, the aerodynamics are substantially more complex. Traditional aerodynamic models and design codes do not adequately account for the floating platform dynamics to assess its effect on turbine loads and performance. Turbines must therefore be over designed due to loading uncertainty and are not fully optimized for their operating conditions. Previous research at the University of Massachusetts, Amherst developed the Wake Induced Dynamics Simulator, or WInDS, a free vortex wake …

Supersonic Turbine Cascade Studies Using Computational Fluid Dynamics And Water Table Experiments, Shelby E. Nelson

Honors College Theses

Design engineers use a variety of tools to perform calculations and to aid in the design process. For example, engineers designing gas turbines, specifically the aerodynamicists, use a combination of hand calculations, experimental data, and complex numerical codes to simulate air flow around each blade. Aerodynamicists designing gas turbines must predict the locations of the shocks to locate inefficiencies in the flow. In this thesis, three methods of calculating the shock angles are compared: analytical, experimental, and computational. Three different airfoil shapes are tested: a rectangular flat plate, a supersonic diamond, and a turbine airfoil. Cascade tests of the airfoil …

Development And Verification Of A Navier-Stokes Solver With Vorticity Confinement Using Openfoam, Austin Barrett Kimbrell

Masters Theses

Vorticity Confinement (VC) is a numerical technique which enhances computation of fluid flows by acting as negative diffusion within the limit of vortical regions, preventing the inherent numerical dissipation present with conventional methods. VC shares similarities with large eddy simulation (LES), but its behavior is based on a stable negative dissipation of vortical structures controlled by the automatic balance between two parameters, μ [mu] and ε [epsilon].

In this thesis, three-dimensional, parallel-computing Navier-Stokes solvers with VC are developed using the OpenFOAM computational framework. OpenFOAM is an open-source collection of C++ libraries developed for computational fluid dynamics. Object-oriented programming concepts are …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …