Aerospace Engineering Commons^™

Experiments And Simulations Of Liquid Mass Gauging And Slosh Dynamics In Microgravity, Jedediah Morse Storey

Theses and Dissertations

Advancements in liquid propellant management science and technologies are key to increasing safety, decreasing cost, and increasing payload mass of space missions. Propellant usually comprises a large portion of the total mass of launch vehicles and spacecraft, so liquid propellant sensing, as well as predicting and controlling the motion of it, are important. Electrical Capacitance Tomography (ECT) is an emerging sensing technology that is capable of measuring the distribution of liquid anywhere inside of a tank, potentially making it useful for measuring slosh and gauging mass. An ECT-instrumented tank was successfully tested in microgravity for the first time. Basics of …

Patch-Wise Training With Convolutional Neural Networks To Synthetically Upscale Cfd Simulations, John P. Romano, Alec C. Brodeur, Oktay Baysal

Mechanical & Aerospace Engineering Faculty Publications

This paper expands the authors’ prior work[1], which focuses on developing a convolutional neural network (CNN) model capable of mapping time-averaged, unsteady Reynold’s-averaged Navier-Stokes (URANS) simulations to higher resolution results informed by time-averaged detached eddy simulations (DES). The authors present improvements over the prior CNN autoencoder model that result from hyperparameter optimization, increased data set augmentation through the adoption of a patch-wise training approach, and the predictions of primitive variables rather than vorticity magnitude. The training of the CNN model developed in this study uses the same URANS and DES simulations of a transonic flow around several NACA 4-digit airfoils …

Jet Noise Reduction: A Fresh Start, Christopher K. Tam, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Attempts to reduce jet noise began some 70 years ago. In the literature, there have been many publications written on this topic. By now, it is common knowledge that jet noise consists of a number of components. They possess different spectral and radiation characteristics and are generated by different mechanisms. It appears then that one may aim at the suppression of the noise of a single component instead of trying to reduce jet noise overall. The objective of the present project is to reduce large turbulence structures noise. It is the most dominant noise component radiating in the downstream direction. …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Proper Orthogonal Decomposition Of Reynolds And Dispersive Stresses In Turbulent Boundary Layers Over Multi-Scale Rough Patches, Catherine Virginia Spivey

Dissertations and Theses

Multi-scale rough patches are present in topologies such as urban canopies (cities) and natural landscapes (forests, ocean floors). The flow over such canopies is three-dimensional, with turbulent structures known as secondary flows present in the boundary layer due to the difference in rough surface heterogeneities. Three dimensional instantaneous velocities are analyzed within the roughness sublayer over three generations of multi-scale rough patches at nine vertical planes using particle image velocimetry obtained experimentally. The secondary structures present in the flow are identified in the form of Reynolds and dispersive fluctuations. Proper orthogonal decomposition is employed to characterize the imprint of the …

Investigating Ground Interactions Of A Rotocraft Landing Vehicle On Titan, Adam Rozman

Honors Undergraduate Theses

The exploration of celestial bodies has recently advanced from rovers to rotorcraft. This includes the recent flights of Mars Ingenuity and the upcoming Dragonfly mission to explore the terrain of Saturn’s moon Titan as part of NASA’s New Frontiers Program. Flight-based landers can travel quickly to sites kilometers apart and land in complex terrain. Although cruise conditions for these rotorcrafts are well understood, studies are necessary to understand take-off and landing. In ground effect conditions, a rotor wake impinges and reflects off the ground, creating changes in aerodynamics such as increased lift. Additionally, operating over loose surfaces, the rotors can …

Modeling Dewetting, Demixing, And Thermal Effects In Nanoscale Metal Films, Ryan Howard Allaire

Dissertations

Thin film dynamics, particularly on the nanoscale, is a topic of extensive interest. The process by which thin liquids evolve is far from trivial and can lead to dewetting and drop formation. Understanding this process involves not only resolving the fluid mechanical aspects of the problem, but also requires the coupling of other physical processes, including liquid-solid interactions, thermal transport, and dependence of material parameters on temperature and material composition. The focus of this dissertation is on the mathematical modeling and simulation of nanoscale liquid metal films, which are deposited on thermally conductive substrates, liquefied by laser heating, and subsequently …

Electric Field Induced Self-Assembly Of Mesoscale Structured Materials And Smart Fluids, Suchandra Das

Dissertations

This dissertation aims to study the forces that drive self-assembly in binary mixtures of particles suspended in liquids and on fluid-liquid interfaces when they are subjected to a uniform electric or magnetic field. Three fluid-particle systems are investigated experimentally and theoretically : (i) Suspensions of dielectric particles in dielectric liquids; (ii) Suspensions of ferromagnetic and diamagnetic particles in ferrofluids; and (iii) Dielectric particles on dielectric fluid-liquid interfaces. The results of these studies are then used to estimate the parameter values needed to assemble materials with desired mesoscale microstructures.

The first fluid-particle system studied is an electrorheological (ER) fluid formed using …

Parallel Anisotropic Unstructured Grid Adaptation, Christos Tsolakis, Nikos Chrisochoides, Michael A. Park, Adrien Loseille, Todd Michal

Computer Science Faculty Publications

Computational fluid dynamics (CFD) has become critical to the design and analysis of aerospace vehicles. Parallel grid adaptation that resolves multiple scales with anisotropy is identified as one of the challenges in the CFD Vision 2030 Study to increase the capacity and capability of CFD simulation. The study also cautions that computer architectures are undergoing a radical change, and dramatic increases in algorithm concurrency will be required to exploit full performance. This paper reviews four different methods to parallel anisotropic grid adaptation. They cover both ends of the spectrum: 1) using existing state-of-the-art software optimized for a single core and …

Studies Of Two-Phase Flow With Soluble Surfactant, Ryan Peter Atwater

Dissertations

Numerical methods are developed for accurate solution of two-phase flow in the zero Reynolds number limit of Stokes flow, when surfactant is present on a drop interface and in its bulk phase interior. The methods are designed to achieve high accuracy when the bulk Péclet number is large, or equivalently when the bulk phase surfactant has small diffusivity

In the limit of infinite bulk Péclet number the advection-diffusion equation that governs evolution of surfactant concentration in the bulk is singularly perturbed, indicating a separation of spatial scales. A hybrid numerical method based on a leading order asymptotic reduction in this …

Delaying Flow Separation Using Piezoelectric Actuators, Kenechukwu Okoye

Honors Theses

Flow separation causes aircraft to experience an increase in drag degrading their aviation performance. The goal of the study was to delay flow separation on an airfoil by embedding a high-frequency translational piezoelectric actuator along the surface of the airfoil. This study investigated the extent to which the high-frequency translational piezoelectric actuator displaces the flow separation downstream or prevents it altogether utilizing a fog-based flow visualization experiment. The actuators with two actuation surfaces were embedded on the suction surface of an Eppler 862 airfoil model and placed in a low-speed wind tunnel. Dry ice fog streams were injected into the …

Water Walking As A New Mode Of Free Surface Skipping, Randy Craig Hurd, Jesse Belden, Allan F. Bower, Sean Holekamp, Michael A. Jandron, Tadd T. Truscott

Mechanical and Aerospace Engineering Faculty Publications

Deformable elastomeric spheres are evaluated experimentally as they skip multiple times over a lake surface. Some spheres are embedded with small inertial measurement units to measure the acceleration experienced during water surface impact. A model for multiple impact events shows good agreement between measured acceleration, number of skipping events and distanced traveled. The experiment reveals a new mode of skipping, “water walking”, which is observed for relatively soft spheres impacting at low impact angles. The mode occurs when the sphere gains significant angular velocity over the first several impacts, causing the sphere to maintain a deformed, oblong shape. The behavior …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

Electro-Drop Bouncing In Low-Gravity, Erin Stivers Schmidt

Dissertations and Theses

We investigate the dynamics of spontaneous jumps of water drops from electrically charged superhydrophobic dielectric substrates during a sudden step reduction in gravity level. In the brief free-fall environment of a drop tower, with a non-homogeneous external electric field arising due to dielectric surface charges (with surface potentials 0.4-1.8 kV), body forces acting on the jumped drops are primarily supplied by polarization stress and Coulombic attraction instead of gravity. This electric body force leads to a drop bouncing behavior similar to well-known phenomena in 1-g₀, though occurring for much larger drops (~0.5 mL). We show a simple …

Mechanisms And Identification Of Unsteady Separation Development And Remediation, Matthew Scott Melius

Dissertations and Theses

Unsteady flow separation represents a highly complex and important area of study within fluid mechanics. The extent of separation and specific time scales over which it occurs are not fully understood and has significant consequences in numerous industrial applications such as helicopters, jet engines, hydroelectric turbines and wind turbines. A direct consequence of unsteady separation is the erratic movement of the separation point which causes highly dynamic and unpredictable loads on an airfoil. Current computational models underestimate the aerodynamic loads due to the inaccurate prediction of the emergence and severity of unsteady flow separation especially in response to a sudden …

Computational Fluid Dynamic Analysis Of Microbubble Drag Reduction Systems At High Reynolds Number, John D. Goolcharan

FIU Electronic Theses and Dissertations

Microbubble drag reduction (MBDR) is an effective method to improve the efficiency of fluid systems. MBDR is a field that has been extensively studied in the past, and experimental values of up to 80% to 90% drag reduction have been obtained. The effectiveness and simplicity of MBDR makes it a viable method for real world applications, particularly in naval applications where it can reduce the drag between the surface of ships and the surrounding water. A two dimensional single phase model was created in ANSYS Fluent to effectively model the behavior of bubble laden flow over a flat plate. This …

Modeling Shock Waves Using Exponential Interpolation Functions With The Least-Squares Finite Element Method, Bradford Scott Smith Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The hypothesis of this research is that exponential interpolation functions will approximate fluid properties at shock waves with less error than polynomial interpolation functions. Exponential interpolation functions are derived for the purpose of modeling sharp gradients. General equations for conservation of mass, momentum, and energy for an inviscid flow of a perfect gas are converted to finite element equations using the least-squares method. Boundary conditions and a mesh adaptation scheme are also presented. An oblique shock reflection problem is used as a benchmark to determine whether or not exponential interpolation provides any advantages over Lagrange polynomial interpolation. Using exponential interpolation …

Unmanned Aerial Vehicle (Uav) Propulsion Research: Conceptual Studies Of “Ultra-Compact Shaft-Less Jet Engines” For Next Generation Uavs, Tyler Eiguren, Trevor Douglas, Tre Buchanan

Publications

Unmanned Aerial Vehicles are becoming more commonly used in today’s society, ranging anywhere from military applications to entertainment for enthusiasts and hobbyists. The complexity of current generation UAV’s propulsive devices, based upon a scaled turbine engine and separate gas & electrically powered rotating fan blades, require regular maintenance for every 24 hours of flight. This added cost coupled with necessary intricate machinery deters UAV designers from such engines, leaving a void in current production. Our research team believes that by combining a simplified alternative compression & combustion process with an electrically driven fan, we can develop an energy efficient, reliable, …

High Performance Modeling Of Atmospheric Re-Entry Vehicles, Alexandre Martin, Leonardo C. Scalabrin, Iain D. Boyd

Mechanical Engineering Faculty Publications

Re-entry vehicles designed for space exploration are usually equipped with thermal protection systems made of ablative material. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple flow chemistry models. In order to obtain better predictions, an appropriate gas flow chemistry model needs …

Cfd Study On Aerodynamic Effects Of A Rear Wing/Spoiler On A Passenger Vehicle, Mustafa Cakir

Mechanical Engineering Master's Theses

Aerodynamic characteristics of a racing car are of significant interest in reducing car-racing accidents due to wind loading and in reducing the fuel consumption. At the present, modified car racing becomes more popular around the world. Sports cars are most commonly seen with spoilers, such as Ford Mustang, Subaru Impreza, and Chevrolet Corvette. Even though these vehicles typically have a more rigid chassis and a stiffer suspension to aid in high-speed maneuverability, a spoiler can still be beneficial. One of the design goals of a spoiler is to reduce drag and increase fuel efficiency. Many vehicles have a fairly steep …

A Filter-Forcing Turbulence Model For Large Eddy Simulation Incorporating The Compressible "Poor Man's" Navier--Stokes Equations, Joshua Strodtbeck

Theses and Dissertations--Mechanical Engineering

A new approach to large-eddy simulation (LES) based on the use of explicit spatial filtering combined with backscatter forcing is presented. The forcing uses a discrete dynamical system (DDS) called the compressible ``poor man's'' Navier--Stokes (CPMNS) equations. This DDS is derived from the governing equations and is shown to exhibit good spectral and dynamical properties for use in a turbulence model. An overview and critique of existing turbulence theory and turbulence models is given. A comprehensive theoretical case is presented arguing that traditional LES equations contain unresolved scales in terms generally thought to be resolved, and that this can only …

Simulations Of Flow Over Wind Turbines, Dnyanesh A. Digraskar

Masters Theses 1911 - February 2014

One of the most abundant sources of renewable energy is wind. Today, a considerable amount of resources are being utilized for research on harnessing the wind energy efficiently. Out of all the factors responsible for efficient energy production, the aerodynamics of flow around the wind turbine blades play an important role. This work aims to undertake aerodynamic analysis of a Horizontal Axis Wind Turbine. A steady state, incompressible flow solver for multiple reference frames, MRFSimple- Foam is modified and used for performing simulations of flow over National Renewable Energy Laboratory Phase VI wind turbine rotor. The code is first tested …

Least-Squares, Continuous Sensitivity Analysis For Nonlinear Fluid-Structure Interaction, Douglas P. Wickert

Theses and Dissertations

A least-squares, continuous sensitivity analysis method is developed for transient aeroelastic gust response problems to support computationally efficient analysis and optimization of aeroelastic design problems. A key distinction between the local and total derivative forms of the sensitivity system is introduced. The continuous sensitivity equations and sensitivity boundary conditions are derived in local derivative form which is shown to be superior for several applications. The analysis and sensitivity problems are both posed in a first-order form which is amenable to a solution using the least-squares finite element method. Several example and validation problems are presented and solved, including elasticity, fluid, …

An Investigation Of Shock Wave Physics Via Hybrid Cfd-Bgk Solution Methods For Nonequilibrium Flows, Brook I. Bentley

Theses and Dissertations

The Unified Flow Solver, a hybrid continuum-rarefied code, is used to investigate the internal structure of a normal shock wave for a Mach range of 1.55 to 9.0 for Argon, and 1.53 to 3.8 for diatomic Nitrogen. Reciprocal shock thickness, density, temperature, heat flux, and the velocity distribution function are calculated for a one-dimensional shock wave and compared with experimental data from Alsmeyer and DSMC results from Bird. Using the Euler, Navier-Stokes, BGK model, and Three-Temperature BGK model schemes, results from UFS compare well with experiment and DSMC. The Euler scheme shows atypical results, possibly resulting from modifications made to …

Filtered Rayleigh Scattering Measurements In A Buoyant Flow Field, Steven M. Meents

Theses and Dissertations

Filtered Rayleigh Scattering (FRS) is a non-intrusive, laser-based flow characterization technique that consists of a narrow linewidth laser, a molecular absorption filter, and a high resolution camera behind the filter to record images. Gases of different species have different molecular scattering cross-sections that become apparent as they pass through the interrogating laser light source, and this difference is used to discriminate between the different gaseous components. This study focuses on the behavior of a buoyant helium jet exiting horizontally into ambient air, and more specifically this jet’s tendency to form side lobes that are discharged from the core fluid under …

Extending Cfd Modeling To Near-Continuum Flows Using Enhanced Thermophysical Modeling, Abram E. Claycomb

Theses and Dissertations

The constitutive relations found in traditional Navier-Stokes-based computational fluid dynamics solvers are known to be limited in altitude. The presence of nonequilibrium phenomena beyond what these methods are able to predict becomes more prevalent at higher altitudes, or increasing Knudsen number. The bulk viscosity, normally assumed to be zero in most computational fluid dynamics applications, is examined as a means of increasing the range of applicability of computational fluid dynamics. The bulk viscosity model used was from recent calculations available in the literature, from a new anisotropic potential energy surface, and is restricted to temperatures below 2000 K. The normal …

Cfd Analysis Of A T-38 Wing Fence, Daniel A. Solfelt

Theses and Dissertations

A computational study of the effects of a wing fence on the T-38 Talon was performed. RANS simulations were conducted using the CFD solver AVUS to examine the flow around the T-38 and the fence at a Reynolds number of 10 million. The T-38 was modeled as a half aircraft with a symmetry plane down the center line and did not include the empennage. The engine inlet and exhaust were modeled as sink and source boundary conditions using mass flow and pressure specifications. Two fence geometries placed 26" from the wing tip were tested. The first fence, called a simple …

Filtered Rayleigh Scattering Measurements In A Bouyant Flowfield, Christopher C. Mcgaha

Theses and Dissertations

Filtered Rayleigh Scattering (FRS) is a non-intrusive technique for studying flowfields. Molecular scattering provides the signal to the camera, and the difference in molecular cross section can be used to discriminate between unmixed gaseous components. The focus of this research is to document the behavior of a horizontal buoyant jet using FRS. A helium jet of precisely controlled mass flow rate is injected into a standard room temperature environment, and FRS provides the means to measure its core trajectory and mixing rate. Trajectory analysis, conducted with consideration of the Reynolds number and Grashof number, can be used to compare these …

Capillary-Driven Flows Along Rounded Interior Corners, Yongkang Chen, Mark M. Weislogel, Cory L. Nardin

Mechanical and Materials Engineering Faculty Publications and Presentations

The problem of low-gravity isothermal capillary flow along interior corners that are rounded is revisited analytically in this work. By careful selection of geometric length scales and through the introduction of a new geometric scaling parameter Tc, the Navier–Stokes equation is reduced to a convenient∼O(1) form for both analytic and numeric solutions for all values of corner half-angle α and corner roundedness ratio λ for perfectly wetting fluids. The scaling and analysis of the problem captures much of the intricate geometric dependence of the viscous resistance and significantly reduces the reliance on numerical data compared with several previous solution methods …

Design And Numerical Simulation Of Two Dimensional Ultra Compact Combustor Model Sections For Experimental Observation Of Cavity-Vane Flow Interactions, David S. Moenter

Theses and Dissertations

An improved computational fluid dynamics (CFD) model was developed for numerical simulation of the Ultra Compact Combustor (UCC) concept to enhance turbulent flow characterization of the circumferentially traveling, centrifugal-force enhanced combustion, cavity flow into the engine main flow passage via a radial cavity in the turbine axial guide vanes. The CFD model uses a dense grid on a 60° periodic, axisymmetric combustor section, with the RNG κ-ε turbulence model to resolve turbulent flow details. An overall analysis and performance evaluation of the experimentally tested UCC configuration and an axially shortened cavity baseline configuration was conducted at various experimentally documented operating …