Engineering Commons^™

Reducing Switching Noise And Losses In Two-Stage Electric Power Converters, Abhijeet Prem

Student Research Symposium

Advancements in semiconductor devices are enabling the design of better electrical power converter systems. Wide Bandgap (WBG) switching devices from Silicon Carbide and Gallium Nitride can operate at high temperatures, voltages, and frequencies with faster turn-on/off periods, improving converter performance over silicon devices. However, WBG technology is still new, and the rapid switching transitions of these devices lead to issues such as voltage overshoots, ringing, and electromagnetic interference, which need to be addressed for widespread adoption. This work introduces a new control method for reshaping the switching voltages, which overcomes the disadvantages of fast transition time without increasing the system's …

Techniques To Overcome Energy Storage Limitations In Electric Vehicles, Matthew J. Hansen

All Graduate Theses and Dissertations, Fall 2023 to Present

Electric vehicles are becoming increasingly popular, battery limitations (cost, size, and weight) complicate electric vehicle adoption. While important research on battery development is ongoing, this dissertation discusses two main approaches to overcome those limitations within the existing battery technology paradigm. Those thrusts are: improving battery health through an optimal charging strategy and minimizing necessary battery size through dynamic wireless power transfer. In this dissertation, relevant literature is discussed, with opportunities for further development considered. Within the two thrusts, three objectives sharpen the focus of the research presented here. First, a planning tool is defined for a battery electric bus fleet. …

Fourier Analysis And Optimization Of Inductive Wireless Power Transfer For Electric Vehicle Charging, Andrew P. Foote

Doctoral Dissertations

With the growth of electric vehicle (EV) popularity, different charging options to increase user convenience and reduce charging time such as high power wireless charging are increasingly being developed and researched. Inductive wireless power transfer (WPT) systems for EVs must meet specifications such as stray field, battery power and voltage operating range, efficiency, and ground clearance. The coil geometry and design have a large impact in meeting these constraints. Typical design approaches include iterative analysis of predetermined coil geometries to identify candidates that meet these constraints.

This work instead directly generates WPT coil shapes and magnetic fields to meet specifications …

Capabilities Of Sintered Silver As A High Temperature Packaging Material, Bakhtiyar Mohammad Nafis

Graduate Theses and Dissertations

With electrification progressing across many sectors including industry, automotive and aerospace, the power density requirements are changing. The increased power density results in higher and higher ambient temperatures that electronics are exposed to. The response has been to move towards wide bandgap (WBG) semiconductor devices that can withstand much greater temperatures and can operate at much higher voltages than silicon. Additionally, these WBG devices deliver low drain-source on resistance (RDS_on) capabilities, enabling high current power modules that increase power density even further. This also requires the packaging to evolve in order to withstand the new requirements. As a result, researchers …

Design Of Hybrid Inverters Using Wideband Gap Semiconductors For Microgrid Application, Luca Gacy

Electronic Theses and Dissertations

As the world becomes more reliant on renewable energy sources such as solar and wind power, the need for high efficiency high power inverters connected to homes is more relevant than ever. Connecting these renewable energy sources (RES) coupled with an energy storage system (ESS) to the grid through a hybrid inverter, with the highest efficiency and grid stability, is quickly becoming a necessity for the near future. This thesis explores the integration of wide band gap semiconductors for the power stage in these systems, along with the analysis of hybrid inverter topologies and structures. The goal of this thesis …

Design And Implementation Of High-Efficiency, Lightweight, System-Friendly Solid-State Circuit Breaker, Dehao Qin

All Dissertations

Direct current (DC) distribution system has shown potential over the alternative current (AC) distribution system in some application scenarios, e.g., electrified transportation, renewable energy, data center, etc. Because of the fast response speed, DC solid-state circuit breaker (SSCB) becomes a promising technology for the future power electronics intensive DC energy system with fault-tolerant capability. First, a thorough literature survey is performed to review the DC-SSCB technology. The key components for DC-SSCB, including power semiconductors, topologies, energy absorption units, and fault detection circuits, are studied. It is observed that the prior studies mainly focus on the basic interruption capability of the …

Design And Advanced Model Predictive Control Of Wide Bandgap Based Power Converters, Waqar Ahmed Khan

Dissertations (1934 -)

The field of power electronics (PE) is experiencing a revolution by harnessing the superior technical characteristics of wide-band gap (WBG) materials, namely Silicone Carbide (SiC) and Gallium Nitride (GaN). Semiconductor devices devised using WBG materials enable high temperature operation at reduced footprint, offer higher blocking voltages, and operate at much higher switching frequencies compared to conventional Silicon (Si) based counterpart. These characteristics are highly desirable as they allow converter designs for challenging applications such as more-electric-aircraft (MEA), electric vehicle (EV) power train, and the like. This dissertation presents designs of a WBG based power converters for a 1 MW, 1 …

Solid State Lighting/Led Lighting, With Reliability Analysis And Smart Sustainable Energy Solutions, Anjan N. Padmasali Dr.

Technical Collection

Reliability analysis of LED based lighting solutions used in general applications. Daily use LED luminaire performance analysis at different accelerated conditions and prediction of performance for any other conditions. System and component level reliability study and analysis. Develop LED based solutions for any specific application requirements. Currently working on developing measurements, data analysis and solutions in lines with providing smart and sustainable solution applicable to lighting and also energy usage optimizations in any system.

1. https://ieeexplore.ieee.org/document/9537294
2. https://journals.sagepub.com/doi/10.1177/1477153520976936
3. https://ieeexplore.ieee.org/document/9559924
4. https://ieeexplore.ieee.org/document/9108554
5. https://ieeexplore.ieee.org/document/8930628

Power Quality Control And Common-Mode Noise Mitigation For Inverters In Electric Vehicles, Yang Huang

Doctoral Dissertations

Inverters are widely utilized in electric vehicle (EV) applications as a major voltage/current source for onboard battery chargers (OBC) and motor drive systems. The inverter performance is critical to the efficiency of EV system energy conversion and electronics system electro-magnetic interference (EMI) design. However, for AC systems, the bandwidth requirement is usually low compared with DC systems, and the control impact on the inverter differential-mode (DM) and common-mode (CM) performance are not well investigated. With the wide-band gap (WBG) device era, the switching capability of power electronics devices drastically improved. The DM/CM impact that was brought by the WBG device-based …

Analysis And Optimization Of The Two-Phase Series Capacitor Buck Dc-Dc Converter, Salahaldein Ali Aboajila Ahmed

Graduate Theses and Dissertations

Current sharing schemes for conventional multi-phase converters are based on sensing each phase current to deliver the current information to their controllers. In conventional buck converters, this fact may require a preset current sharing ratio at the expense of efficiency, which eventually requires a larger sensing circuit to achieve the sensing accuracy of each phase. Introducing the concept of automatic current sharing is one of the solutions to tackle this issue. Automatic current sharing (Current Sharing Mechanism CSM) is an advanced way to distribute heat generation in multi-phase switching topologies at full load. A two-phase series capacitor buck converter (2-pscB) …

Reactive Power Sharing And Voltage Restoration In Islanded Ac Microgrids, Khurram Hashmi, Rizwan Ali, Muhammad Hanan, Waseem Aslam, Abubakar Siddique, Muhammad Mansoor Khan

Turkish Journal of Electrical Engineering and Computer Sciences

Microgrids (MG) are a new and innovative concept in modern distribution networks. Several challenges are associated with the operation and control of MG networks. Active and reactive power sharing among energy resources interfaced through power electronic conversion stages is a major challenge. Although active power sharing can be achieved under varying scenarios, sharing of reactive power between distributed generation units is difficult to achieve. This paper presents a novel and innovative control scheme to ensure sharing of reactive power between Distributed generation units within an autonomous, islanded AC microgrid. A framework composed of novel multiagent moving average estimators is proposed …

Power Line Coupling Power Supply Design, Janine Gian Christii C. Darato, Jeni K. Kawate, Nicholas A. Marta

Electrical Engineering

In this project, a power supply was designed for a startup company, Perch Sensing, to detect wildfires with the use of distributed sensors across power lines. The purpose of the power supply is to provide 15W of power to a microcontroller, which controls the sensor nodes. The power supply hangs from power lines and draws energy by inductively coupling to these lines. Our design starts with a current transformer that steps down the current from the power line, which is fed into a shunting mechanism as a safety precaution when the load is absent, then to the power supply itself. …

Real-Time Probabilistic Solvers For Digital Twins Of Power Electronic Systems, Matthew Aaron Milton

Theses and Dissertations

In recent years, switching power electronic systems for use in power conversion, generation, and distribution have become increasingly larger and complex in their design. With the increase in complexity comes the increase in difficulty in performing analysis, experiments, and health management on such systems in physical space. Part of this difficulty comes from challenge of access to and understanding of the internal interplay of the numerous components, safety and cost of system operation, and the inherent uncertainty of physical characteristics of systems and their environment.

A recent approach for testing and diagnostics/prognostics of power electronic systems is the application of …

A Comprehensive Review On Brushless Doubly-Fed Reluctance Machine, Omid Sadeghian, Sajjad Tohidi, Behnam Mohammadi-Ivatloo, Fazel Mohammadi

Electrical and Computer Engineering Publications

© 2021 by the authors. Licensee MDPI, Basel, Switzerland. The Brushless Doubly-Fed Reluctance Machine (BDFRM) has been widely investigated in numerous research studies since it is brushless and cageless and there is no winding on the rotor of this emerging machine. This feature leads to several advantages for this machine in comparison with its induction counterpart, i.e., Brushless Doubly-Fed Induction Machine (BDFIM). Less maintenance, less power losses, and also more reliability are the major advantages of BDFRM compared to BDFIM. The design complexity of its reluctance rotor, as well as flux patterns for indirect connection between the two windings mounted …

Special Power Electronics Converters And Machine Drives With Wide Band-Gap Devices, Yibin Zhang

Theses and Dissertations--Electrical and Computer Engineering

Power electronic converters play a key role in power generation, storage, and consumption. The major portion of power losses in the converters is dissipated in the semiconductor switching devices. In recent years, new power semiconductors based on wide band-gap (WBG) devices have been increasingly developed and employed in terms of promising merits including the lower on-state resistance, lower turn-on/off energy, higher capable switching frequency, higher temperature tolerance than conventional Si devices. However, WBG devices also brought new challenges including lower fault tolerance, higher system cost, gate driver challenges, and high dv/dt and resulting increased bearing current in electric machines.

This …

Survey Of Dc-Dc Non-Isolated Topologies For Unidirectional Power Flow In Fuel Cell Vehicles, Mahajan Sagar Bhaskar, Vigna K. Ramachandaramurthy, Sanjeevikumar Padmanaban, Frede Blaabjerg, Dan M. Ionel, Massimo Mitolo, Dhafer Almakhles

Power and Energy Institute of Kentucky Faculty Publications

The automobile companies are focusing on recent technologies such as growing Hydrogen (H2) and Fuel Cell (FC) Vehicular Power Train (VPT) to improve the Tank-To-Wheel (TTW) efficiency. Benefits, the lower cost, `Eco' friendly, zero-emission and high-power capacity, etc. In the power train of fuel cell vehicles, the DC-DC power converters play a vital role to boost the fuel cell stack voltage. Hence, satisfy the demand of the motor and transmission in the vehicles. Several DC-DC converter topologies have proposed for various vehicular applications like fuel cell, battery, and renewable energy fed hybrid vehicles etc. Most cases, the DC-DC power converters …

Modeling And Optimization Algorithm For Sic-Based Three-Phase Motor Drive System, Ren Ren

Doctoral Dissertations

More electric aircraft (MEA) and electrified aircraft propulsion (EAP) becomes the important topics in the area of transportation electrifications, expecting remarkable environmental and economic benefits. However, they bring the urgent challenges for the power electronics design since the new power architecture in the electrified aircraft requires many benchmark designs and comparisons. Also, a large number of power electronics converter designs with different specifications and system-level configurations need to be conducted in MEA and EAP, which demands huge design efforts and costs. Moreover, the long debugging and testing process increases the time to market because of gaps between the paper design …

Cybersecurity Methods For Grid-Connected Power Electronics, Stephen Joe Moquin

Graduate Theses and Dissertations

The present work shows a secure-by-design process, defense-in-depth method, and security techniques for a secure distributed energy resource. The distributed energy resource is a cybersecure, solar inverter and battery energy storage system prototype, collectively called the Cybersecure Power Router. Consideration is given to the use of the Smart Green Power Node for a foundation of the present work. Metrics for controller security are investigated to evaluate firmware security techniques. The prototype's ability to mitigate, respond to, and recover from firmware integrity degradation is examined. The prototype shows many working security techniques within the context of a grid-connected, distributed energy resource. …

Study Of A Symmetrical Llc Dual-Active Bridge Resonant Converter Topology For Battery Storage Systems, John K. George

Graduate Theses and Dissertations

A symmetrical LLC resonant converter topology with a fixed-frequency quasi-triple phase-shift modulation method is proposed for battery-powered electric traction systems with extensions to other battery storage systems. Operation of the converter with these methods yields two unique transfer characteristics and is dependent on the switching frequency. The converter exhibits several desirable features: 1) load-independent buck-boost voltage conversion when operated at the low-impedance resonant frequency, allowing for dc-link voltage regulation, zero-voltage switching across a wide load range, and intrinsic load transient resilience; 2) power flow control when operated outside the low-impedance resonance for integrated battery charging; 3) and simple operational mode …

Experimental Investigation Of Low-Voltage Silicon Carbide (Sic) Semiconductor Devices For Power Conversion Applications, Saleh Salem H. Alharbi

Electronic Theses and Dissertations

Enhancing the performance and efficiency of power converter systems requires fast-switching power devices with considerably low switching and conduction losses. Silicon (Si) semiconductor devices are the essential components in electronic converter designs, and their behaviors and switching characteristics determine the system’s overall performance and efficiency. These conventional Si devices are nearing to hit their physical and operational limits in meeting power converter requirements with respect to high temperature and large voltage conditions. However, silicon carbide (SiC) power devices enable greater converter efficiency and better power density, particularly under hard switching frequencies and high output voltages due to their outstanding material …

Design And Application Of Spwm Based 21-Level Hybrid Inverter For Induction Motor Drive, Sheikh Tanzim Meraj, Kamrul Hasan, Ammar Masaoud

Turkish Journal of Electrical Engineering and Computer Sciences

Thispaperpresentstheapplicationofanewlydeveloped21-levelhybridmultilevelinverter. Ahighfrequency modulation technique known as sinusoidal pulse width modulation (SPWM) is applied to the hybrid inverter. This modulation methodology operates the switching sequences of the multilevel inverter to produce the desired 21-level output voltage. To validate the proper application of this inverter, it is further utilized to maintain the speed of a single phase induction motor. The velocity control of the motor is established on the principle of V/f control technique. The speed control strategy along with the compatibility of the SPWM modulation technique were verified by means of simulation and experimental results.

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

Split Dc Bus Converters For Power Electronic And Ac-Dc Microgrid Applications, Javad Khodabakhsh

Electronic Thesis and Dissertation Repository

Power electronic converters are used extensively for electrical power conversion in applications such as renewable energy systems, utility applications, and electric vehicles. Such converters are needed as it is rare for a source voltage to fit the needs of a load or a set of loads for any particular application. They consist of active semiconductor switches and passive components that are combined in circuit structures (topologies) that are operated with a control strategy. The focus of this thesis is on AC-DC and DC-DC converters and their applications in AC-DC microgrids.

AC-DC converters are typically two-stage converters that consist of a …

Local And Central Controllers For Microgrids, Edgar Ariel Escala Calame

Graduate Theses and Dissertations

The main objective of this thesis is to serve as a guide, so readers are able to learn about microgrids and to design simple controllers for different AC microgrid applications. In addition, this thesis has the objective to provide examples of simulation cases for the hierarchical structure of a basic AC microgrid which can be used as a foundation to build upon, and achieve more complex microgrid structures as well as more sophisticated power-converter control techniques.

To achieve these objectives, the modeling of voltage source converters and control design in the z-domain are presented. Moreover, the implementation and transient analysis …

Device Engineering Of Algan/Gan Hemts For Applications In Power-Electronic And Sensing, Isra Mahaboob

Legacy Theses & Dissertations (2009 - 2024)

The research work presented in this Ph.D. thesis focuses on the engineering of AlGaN/GaN high electron mobility transistors (HEMTs) for the development of future device technology in power electronic and sensing applications.

Design Optimization Of Inductive Power Transfer Systems For Contactless Electric Vehicle Charging Applications, Masood Moghaddami

FIU Electronic Theses and Dissertations

Contactless Electric Vehicle (EV) charging based on magnetic resonant induction is an emerging technology that can revolutionize the future of the EV industry and transportation systems by enabling an automated and convenient charging process. However, in order to make this technology an acceptable alternative for conventional plug-in charging systems it needs to be optimized for different design measures. Specifically, the efficiency of an inductive EV charging system is of a great importance and should be comparable to the efficiency of conventional plug-in EV chargers.

The aim of this study is to develop solutions that contribute to the design enhancement of …

Investigating Efficiency Of Ac Direct Drive Of Led Lighting, Miles Davis Head

Electrical Engineering

This project explores the rapidly-expanding area of AC direct drive for LED lighting. AC LED driving does not use typical DC-DC converter-based driving but uses semiconductor switches and a linear regulator to activate a number of LEDs proportional to the input voltage at any given time. This allows bulky, expensive magnetics to be eliminated from the system. The goal of this project was to develop a flexible simulation of a common AC LED system to find areas of significant power loss and attempt to improve them. This allows future versions of an AC LED system to start with major loss …

Microgrid Reliability Evaluation Based On Condition-Dependent Failure Models Of Power Electronic Devices, Qi Li

Theses and Dissertations

Microgrid, a distributed energy system consisting of distributed energy and loads, aims to ensure reliable and affordable energy security in urban and rural communities. With the growing global energy need and the emerging threat of climate change, green renewable energy is becoming a new favorite in the field of power generation. Microgrids have received wide spread attention and application for their minimizing carbon dioxide and greenhouse gas emissions. Microgrids do so by maximizing clean local energy generation as well

as reducing the stress of the transmission and distribution system.

With the use of renewable energy, the reliability performance of microgrids …

Scada And Plc Systems Configuration For The Ncrept Test Facility, Arman Ahmed

Electrical Engineering Undergraduate Honors Theses

This thesis details the project to update the control and interface system of the National Center for Reliable Electric Power Transmission (NCREPT) testing facility. The need for this project arose from the 2017-2018 expansion of the facility, which included some modifications in the layout of electrical equipment used for testing purposes. These modifications necessitated the update of the control and interface system. Additionally, the old system was implemented a decade ago and is nearing obsolescence, so the facility’s expansion served as an opportune time for an upgrade.

There were two main parts to the scope of this project, which were …

Advanced Topologies Of High-Voltage-Gain Dc-Dc Boost Converters For Renewable Energy Applications, Ahmad Alzahrani

Doctoral Dissertations

This dissertation proposes several advanced power electronic converters that are suitable for integrating low-voltage dc input sources, such as photovoltaic (PV) solar panels, to a high voltage dc bus in a 200 - 960 V dc distribution system. The proposed converters operate in the continuous conduction mode (CCM) and offer desirable features such as low-voltage stresses on components, continuous input currents, and the ability to integrate several independent dc input sources. First, a family of scalable interleaved boost converters with voltage multiplier cells (VMC) is introduced. Several possible combinations of Dickson and Cockcroft-Walton VMCs are demonstrated and compared in terms …