Engineering Commons^™

Pavement Quality Indicators Study, Wayne Jensen Ph.D., Cody Kluver

Mid-America Transportation Center: Final Reports and Technical Briefs

The Nebraska Department of Roads (NDOR) conducts annual examinations of the Nebraska’s interstate and federal high-way pavements. During these examinations, numerous indicators of pavement quality are measured directly or are com-piled from parameters recorded by a vehicle passing over the pavement section. Parameters are documented and analyzed for each one-tenth mile segment. A number of pavement sections where innovative features have been incorporated were selected by the NDOR for comparison to nearby conventional pavement sections. This study used data recorded by the NDOR as well as field observations to develop a comparison between two pavement sections, one with innovative fea-tures …

Investigation Of Asphalt Pavement Analyzer Testing Program In Nebraska, Minki Hong, Yong-Rak Kim

Mid-America Transportation Center: Final Reports and Technical Briefs

The asphalt pavement analyzer (APA) has been widely used to evaluate hot-mix asphalt (HMA) rutting potential in mix design and quality control – quality assurance (QC-QA) applications, because the APA testing and its data analyses are relatively simple, rapid, and easy. However, as demonstrated in many studies and also experienced by the state of Nebraska, the APA testing is in question due to its high testing variability and a lack of sufficient correlation with actual filed performance. The primary objective of this research was to find critical materials and/or mixture design factors affecting APA test results so as to eventually …

Evaluation Of An Existing Steel Post Alternative For The Thrie Beam Bullnose Guardrail System, Robert W. Bielenberg, Ronald K. Faller, John R. Rohde, John D. Reid

Mid-America Transportation Center: Final Reports and Technical Briefs

Recently, the Minnesota Department of Transportation (MnDOT) funded a research project through the Midwest States Regional Pooled Fund to evaluate an existing steel post alternative for the thrie beam bullnose barrier system previously developed at the Midwest Roadside Safety Facility (MwRSF). MnDOT had an interest in the replacement of the wooden breakaway posts used in the current bullnose system with proprietary breakaway steel posts. The research project consisted of evaluation of current breakaway steel post designs, investigation and selection of a candidate post design, and full-scale testing of the bullnose system with a steel post alternative. The full-scale testing was …

Dynamic Impact Testing Of W152x13.4 (W6x9) Steel Posts On A 2:1 Slope, Gopi Dey, Ronald K. Faller, John A. Hascall, Robert W. Bielenberg, Karla A. Polivka, Kirk Molacek

Mid-America Transportation Center: Final Reports and Technical Briefs

Dynamic impact testing of W152x13.4 (W6x9) steel posts at various embedment depths has been detailed, and the results stated. A total of 17 bogie tests have been performed on a 2:1 slope, with post lengths varying from 1,829 mm (6 ft) through 2,743 mm (9 ft). A total of four bogie tests were performed on level terrain using 1,829-mm (6-ft) long steel posts at two different impact speeds. For each bogie test, raw acceleration data, obtained from accelerometers, was filtered and then force-displacement and energy-displacement graphs were plotted. From the energy-displacement graphs, the average post-soil forces were calculated for a …

Investigating The Use Of Small-Diameter Softwood As Guardrail Posts (Dynamic Test Results), Jason A. Hascall, Ronald K. Faller, John D. Reid, Dean L. Sicking, David E. Kretschmann

Mid-America Transportation Center: Final Reports and Technical Briefs

A modified version of the Midwest Guardrail System (MGS), utilizing small-diameter round wood posts, was developed, tested, and evaluated. Three systems were developed using different species of timber, Douglas Fir, Ponderosa Pine, and Southern Yellow Pine. A combination of Barrier VII computer simulation modeling and several series of cantilever bogie tests, conducted in both a rigid sleeve and soil, were used to determine the required diameter of post for each species in order to serve as an equivalent substitute for the standard steel post used in the barrier system. The final recommended nominal sizes were determined to be 184 mm …

Performance Evaluation Of The Permanent New Jersey Safety Shape Barrier – Update To Nchrp 350 Test No. 4-12 (2214nj-2), Karla A. Polivka, Ronald K. Faller, Dean L. Sicking, John R. Rohde, Robert W. Bielenberg, John D. Reid, Brian A. Coon

Mid-America Transportation Center: Final Reports and Technical Briefs

Based on the proposed changes to the National Cooperative Highway Research Program (NCHRP) Report No. 350 guidelines, NCHRP Project 22-14(2) researchers deemed it appropriate to evaluate permanent safety shape barrier systems prior to finalizing the new crash testing procedures and guidelines. For this effort, the permanent New Jersey Safety Shape barrier was selected for evaluation. One full-scale vehicle crash test was performed on the longitudinal barrier system in accordance with the Test Level 4 (TL-4) requirements presented in the Update to NCHRP Report No. 350. For the permanent barrier testing program, a 10000S single unit truck was used.

The permanent …

Performance Evaluation Of The Midwest Guardrail System – Update To Nchrp 350 Test No. 3-11 With 28" C.G. Height (2214mg-2), Karla A. Polivka, Ronald K. Faller, Dean L. Sicking, John R. Rohde, Robert W. Bielenberg, John D. Reid

Mid-America Transportation Center: Final Reports and Technical Briefs

Based on the proposed changes to the National Cooperative Highway Research Program (NCHRP) Report No. 350 guidelines, NCHRP Project 22-14(2) researchers deemed it appropriate to evaluate a strong-post W-beam guardrail systems prior to finalizing the new crash testing procedures and guidelines. For this effort, the Midwest Guardrail System (MGS) was selected for evaluation. One full-scale vehicle crash test was performed on the longitudinal barrier system in accordance with the Test Level 3 (TL-3) requirements presented in the Update to NCHRP Report No. 350. For this test, a 2270P pickup truck vehicle, which was a 1⁄2-ton, four-door vehicle with a 711 …

Safety Performance Evaluation Of Michigan’S 4x5 Portable Sign Support, Ronald K. Faller, James C. Holloway, John R. Rohde, Dean L. Sicking

Mid-America Transportation Center: Final Reports and Technical Briefs

A wide variety of traffic controlling devices are used in work zones, some of which are not normally found on the roadside or in the traveled way outside of the work zones. These devices are used to enhance the safety of the work zones by controlling the traffic through these areas. Due to the placement of the traffic control devices, the devices themselves may be potentially hazardous to both workers and errant vehicles. The impact performance of many work-zone traffic control devices is mainly unknown and to date limited crash testing has been conducted, under the criteria of National Cooperative …

Performance Analysis Of Welch Products Recycled Rubber Spacer Block, Bob W. Bielenberg, Ronald K. Faller

Mid-America Transportation Center: Final Reports and Technical Briefs

The Midwest Roadside Safety Facility was contracted by Will Stein of the Iowa Department of Transportation to conduct dynamic bogie testing of a recyclable rubber guardrail spacer block manufactured by Welch Products, Inc. The scope of the work included the setup of both a standard, wood guardrail post blockout and the Welch Products recycled rubber blockout on a standard W150x13.5 steel post, as well as two component tests using a bogie vehicle. The bogie tests were conducted in accordance with previously accepted procedures to evaluate the performance of guardrail post blockouts made of non-standard materials.

Guidelines For Attachments To Bridge Rails And Median Barriers, Eric A. Keller, Dean L. Sicking, Ronald K. Faller, Karla A. Polivka

Mid-America Transportation Center: Final Reports and Technical Briefs

Highway agencies are often presented with the need to add attachments of various configurations to the top or backside of crashworthy traffic barriers. Although, the National Cooperative Highway Research Program (NCHRP) Report No. 350 offers guidance for the safety performance evaluation of traffic barriers, it offers no guidance toward the evaluation of attachments on or near these barriers. The objective of the research project was to collect crash test data relating to bridge rails and median barriers, to collect information about common attachments to traffic barriers, and to evaluate this information for the purpose of developing guidelines for the design …

Development Of A Low-Profile Bridge Rail For Test Level 2 Applications, Karla A. Polivka, Ronald K. Faller, Dean L. Sicking, John R. Rohde, John D. Reid, James C. Holloway

Mid-America Transportation Center: Final Reports and Technical Briefs

A low-profile bridge rail was developed for installations where pedestrians and/or site restrictions prevent the use of conventional bridge rails with transitions. The bridge rail design was constructed using a 22.86-m long reinforced concrete parapet. The entire system measured 508-mm high by 356-mm and 279-mm wide at the top and bottom surfaces, respectively.

The research study included one full-scale vehicle crash test, using a 3⁄4-ton pickup truck. The full- scale test, impacting at a speed of 70.0 km/hr and an angle of 27.1 degrees, was conducted and reported in accordance with the requirements specified in National Cooperative Highway Research Program …

Development And Evaluation Of A Tie-Down System For The Redesigned F-Shape Concrete Temporary Barrier, Karla A. Polivka, Ronald K. Faller, John R. Rohde, James C. Holloway, Bob W. Bielenberg, Dean L. Sicking

Mid-America Transportation Center: Final Reports and Technical Briefs

Often, temporary barriers are used in applications where it is desired that their deflection during vehicular impact be limited. One such application is in the installation of temporary barriers placed adjacent to the edge of a concrete bridge deck in order to maximize lane width. Acceptable tie-down systems for temporary barriers have previously been developed, but there are concerns when the barriers and tie-down systems are used on bridges that are reconstructed in stages and where very little tolerance in barrier deflection is allowable. Therefore, a rigid tie-down system was developed that minimizes barrier deflections. For this system, the original …

Development Of Standards For Placement Of Steel Guardrail Posts In Rock, Jason Herr, John R. Rohde, Dean L. Sicking, John D. Reid, Ronald K. Faller, James C. Holloway, Brian A. Coon, Karla A. Polivka

Mid-America Transportation Center: Final Reports and Technical Briefs

A steel post W-beam guardrail system was developed for installation in rock-soil foundations. The guardrail system was constructed with a 2.66-mm (12-gauge) thick W-beam rail, 53.34 m in length. The W-beam guardrail was supported by twenty-seven W152x13.4 by 1,346-mm long steel posts, spaced at 1,905 mm on center. The posts were installed in drilled holes in concrete, constructed by drilling three 203-mm diameter holes on 165- mm centers to a depth of 610 mm. The drilled holes were backfilled with compacted ASTM C33 coarse aggregate, size no. 57.

One full-scale vehicle crash test, using a 3⁄4-ton pickup truck, was performed …

Bridge Rails And Transitions For Pedestrian Protection, Nicholas R. Hiser, Ronald K. Faller, Dean L. Sicking, John R. Rohde, John D. Reid, Karla A. Polivka

Mid-America Transportation Center: Final Reports and Technical Briefs

It is desirable to protect pedestrians on bridges from motor vehicles. However, transition problems arise at the ends of bridges where the bridge rail, bridge rail end treatment, and pedestrian walkway compete for the limited available space. The objective of this study was to identify the most common scenarios in which the protection of pedestrians on bridges is desirable, and then to develop bridge rail and bridge rail end treatment configurations to accommodate those situations. The objective was achieved by performing a field investigation, a survey of state transportation agencies, and a literature review. Recommendations for the placement and general …

Cable Barrier Literature Review, Brian A. Coon, Ronald K. Faller, John D. Reid

Mid-America Transportation Center: Final Reports and Technical Briefs

A literature review of cable barrier systems.

Crash Testing Of Michigan's Type B (W-Beam) Guardrail System - Phase Ii, Karla A. Polivka, Dean L. Sicking, John A. Rohde, Ronald K. Faller, James C. Holloway

Mid-America Transportation Center: Final Reports and Technical Briefs

Michigan Department of Transportation's Type B (W-beam) longitudinal barrier system was constructed and crash tested. The barrier design was constructed with a 2.66-mm (12-gauge) thick W-beam rail totaling 53.34 m in length. The W-beam rail was supported by twenty-five W152.13.4 steel posts, each measuring 1,830-mm long, and four standard BCT posts, each measuring 1,080-mm long. Each of the steel posts had a 152.203 by 360-mm long standard wood offset blockout. Post spacings were 1,905-mm on center.

The research study included full-scale vehicle crash testing, using a 3/4-ton pickup truck. The test vehicle impacted at a speed of 99.8 km/hr and …

Development Of A 7.62-M Long Span Guardrail System – Phase Ii, Karla A. Polivka, Robert W. Bielenberg, Dean L. Sicking, Ronald K. Faller, John R. Rohde, Eric A. Keller

Mid-America Transportation Center: Final Reports and Technical Briefs

A 7.62-m long span guardrail system was developed for use over low-fill culverts. The long span design was constructed with two 2.66-mm (12-gauge) thick nested W-beam rails totaling 30.48 m in length. The nested W-beam rail was supported by sixteen W150x13.5 steel posts and six standard CRT posts, each with two 150x200x360 wood blockouts. Each post measured 1,830-mm long. Post spacings were 1,905-mm on center except for the 7.62-m spacing between the two CRT posts surrounding the unsupported span.

The research study included full-scale vehicle crash testing, using a 3⁄4-ton pickup truck. The test, impacting at a speed of 102.9 …

Compliance Testing Of Iowa’S Skid-Mounted Sign Device, Karla A. Polivka, Ronald K. Faller, John R. Rohde, James C. Holloway, Dean L. Sicking

Mid-America Transportation Center: Final Reports and Technical Briefs

A wide variety of traffic control devices are used in work zones, some of which are nont ormally found on the roadside or in the traveled way outsideofthe work zones. These devices are used to enhance the safety of the work zones by controlling the traffic through these areas. Due to the placement of the traffic control devices, the devices themselves may be potentially hazardous to both workers and errant vehicles. The impact performance of many work zone traffic control devices is mainly unknown and to date limited crash testing has been conducted under the criteria of National Cooperative Highway …

Development Of A Tl-3 F-Shape Temporary Concrete Median Barrier, Ronald K. Faller, John R. Rohde, Barry T. Rosson, Richard P. Smith, Kenneth H. Addink

Mid-America Transportation Center: Final Reports and Technical Briefs

A temporary concrete median barrier (CMB) was designed and tested for compliance under the Test Level 3 (TL-3) guidelines specified in the Recommended Procedures for the Safety Performance Evaluation of Highway Features, National Cooperative Highway Research Program (NCHRP) Report No. 350. The barrier is built to the new metric standards and has a traditional pin and loop configuration for interconnection. The objective of this research project was to develop and evaluate a standardized, temporary concrete barrier design while addressing the concerns for safety, economy, structural integrity, constructability, ease of installation, and maintenance. The resulting F-shape barrier segment is 3,800-mm …