Engineering Commons^™

Application Of Advanced Computational Modelling In The Numerical Prediction Of The Haemodynamic Impact Of Coronary Stent Implantation, Jonathan Murphy, Fergal Boyle

Conference Papers

Coronary stent implantation can improve blood flow in an artery narrowed by the build up of arterial plaque. However, the haemodynamic effect of stent placement is unclear and may influence arterial restenosis (re-blockage). In this investigation the stent induced, non-Newtonian blood flow disturbances have been captured in a three dimensional computational domain. The results clearly show areas of low wall shear stress proximal and distal to the stent wires, a characteristic which is known to encourage restenosis. Furthermore, this computational method of observing the complex haemodynamics of the stent environment can be used in conjunction with medical trial data to …

Exchange Faculty Perspectives On International Collaborations, Donal Mchale

Conference Papers

The main purpose of the paper is to document key issues in developing successful transatlantic faculty exchanges and to document perspectives and key learnings’ emanating from the development and implementation of an international exchange process.

Thermal Performance Of Low Approach Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Conference Papers

Meteorological enthalpy analysis of temperate and maritime climates above 45˚N suggests that the water-side evaporative cooling technique has considerable unrealised potential with contemporary "high temperature" building cooling systems - such as chilled ceilings. As low approach conditions are the key to exploiting the cooling potential of the ambient air, thermal performance at such conditions needs to be investigated. To address the research issues a test rig, based on an open cooling tower and plate heat exchanger and designed to maximise evaporative cooling potential, has been constructed at DIT. A combination of experimental measurement and analysis is used in the investigations. …

Cutting Rate Effect On Temperature During Cortical Bone Sawing, Hamid Khalili Parsa, Ger Reilly, Brendan Mccormack

Conference Papers

When bone is cut the occurrence of thermal damage to the bone is of major concern to the surgeon. If the temperature exceeds 44°C for longer than 1 min, bone repair is impaired (Eriksson et al, 1984) and necrosis may occur. Repeated use of cutting blades may reduce the cutting efficiency (Wevers et al, 1987; Toksvig-Larsen et al, 1992). Wevers et al also found that there is a greater force required to cut cortical bone using a blunt saw compared to new one.

Indentation Fracture Of Bovine Cortical Bone: Acoustic Emission Technique, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

Indentation cutting may result in microcracking and main crack growth which was previously reported. In this study, we recorded the AE signals produced by cracking processes during cutting on cortical bone, measuring the cutting force and correlating between load-displacement curves and AE activities.

Hand Posture Recognition In Sign Language Using Shape Distributions, Eamonn Young, Gary Clynch

Conference Papers

A shape distribution is a histogram used to uniquely identify different shapes. The histogram is produced by taking random distances on the surface of a shape or object. Theoretically, each shape or object should produce a unique histogram, as the distribution of distances for each shape should be different. Shape distributions have recently been implemented in a number of object recognition areas. They are an attractive method as they are inherently simple, fast and generic. This paper presents the results of research undertaken on the application of shape distributions for the purpose of sign language recognition. There are four main …

A Numerical Acoustic Fluid-Structure Simulation Of Therapeutic Ultrasound Angioplasty, Graham Gavin, Finbar Dolan, M.S J. Hashmi, Garrett Mcguinness

Conference Papers

INTRODUCTION Therapeutic ultrasound angioplasty is the delivery of high amplitude ultrasonic displacements to the distal-tip of small diameter wire waveguides with the goal of disrupting atherosclerotic plaques. This is a minimally invasive procedure that may have potential' in the treatment of complicated chronic total occlusions. The disruption of plaque is due to direct contact ablation and also cavitation, pressure waves and acoustic streaming in the fluid surrounding the vibrating waveguide distal-tip [1]. Cavitation appears to play a major role and some authors have suggested that plaque ablation is only evident above the cavitation threshold [2]. Makin and Everbach [3] performed …

A Numerical Acoustic Fluid-Structure Model Of A Therapeutic Ultrasound Angioplasty Device, Graham Gavin, M.S. J. Hashmi, Finbar Dolan, Garrett Mcguinness

Conference Papers

Ultrasonic angioplasty involves the use of ultrasonic vibrations delivered to the distal-tip of small diameter wire waveguides and is an emerging technology the may have potential use in the treatment of complicated atherosclerotic plaques during cardiovascular surgery. Complicated plaques, including chronic total occlusions and calcified lesions, seriously reduce success rates during standard intervention involving guidewire access, followed by balloon dilation or stent delivery. The large amplitude (0-150 μm) wire waveguide distal-tip displacements in the low-frequency ultrasonic (18-45 kHz) range have been shown to disrupt plaque material by direct contact ablation and cavitation, acoustic streaming and pressure wave components in adjacent …

Alkaline Fuel Cell Engineering And Testing, James Brunton, David Kennedy, Eugene Coyle

Conference Papers

A fuel cell is a device that directly converts the chemical energy of reactants (a fuel and an oxidant) into low d. c. electricity [1]. Used in conjunction with other sustainable energy options, hydrogen and fuel cell technology can provide a realistic alternative to fossil fuels. Although research is continuing in many areas we are no closer now to commercialisation than ten to twenty years ago. This is due to a number of key reasons, some of which include efficiency, scale, accessories and power output. This paper outlines the benefits that could be derived from switching to a hydrogen based …

Refinements In Using Historical Process Data To Optimize Tolerance Allocation, Kevin Delaney, Pat Phelan

Conference Papers

Tolerance allocation for new products calls for experience and judgment. Whenever products are manufactured using production processes that are similar to existing products it is likely that the trend in production tolerances for both the new and existing products will be similar. It must be assumed that there have been no improvements to the tooling, modifications to the machines being used, or a change in process stability. The data employed to understand and exploit these trends is commonly referred to as process capability data and it is stored in a Process Capability DataBase (PCDB). There are several challenges to be …

The Tromped, An In-Flight Exercise Device To Prevent Flight Related Deep Vein Thrombosis, Carolyn Collins, David Kennedy, Thomas Corrigan, Stephen Jerrams

Conference Papers

Medical and Engineering research studies have shown the potential risks of long haul flight travel and methods of preventing it occurring. The risk of serious health problems or even death is known to arise from lack of venous movement and increased coagulation (clotting) of the blood. These factors contribute to the development of deep vein thrombosis (DVT) and this is more likely to occur in situations where people are seated for long periods during travel on land or in air. Currently long haul airlines have yet to be seen to introduce physical preventative measures against this syndrome.

A prototype design …

The Role And Future Of Nanotechnology In Research, Industry And Education, David Kennedy

Conference Papers

Major developments in Nanotechnology have taken place across the world
over the last few years. From a humble beginning, Ireland inc. became a leader in the Microelectronics industry and now has to face the challenge of developing a strategic plan to maintain its lead position in the nano field which in most cases will supersede the micro phase. Most countries are taking a similar path of development all be it alone or in collaboration with other countries. This process is expensive and requires market drivers and experts to lead and deliver demands from the industries of the future. The approach …

Analysis Of Indentation Loading Of Cortical Bone Using Acoustic Emission Techniques, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

In this study, we recorded the number of Acoustic emission (AE) hits and related AE energy during indentation fracture of cortical bone using a PAC PCI-2 card and pico sensor. A threshold value of 43dB was used to filter premature trigger due to background noise. Registered AE hits had more than one count (threshold crossing). Amplifier gain was set at 40dB with a (0.1-1) MHz band pass filter. 8mm cubes of cortical bones were indented in the longitudinal direction at constant crosshead speed of 1 mm min-1 using a large 2D, 50˚ wedge indenter. We hypothesised that signals occurring as …

Detection Of Microcracks During Bone Cutting Using Acoustic Emission Techniques, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

Surgeons may use a number of cutting instruments such as osteotomes and chisels to cut bone during operative procedures. The initial loading of cortical bone during the cutting process results in the formation of microcracks in the vicinity of the cutting zone with main crack propagation to failure occurring with continued loading; microcracking acts as a stimulus for main crack formation and has also been shown to occur during the propagation of the main crack. It has also been reported that Acoustic Emission (AE) is generated due to microcrack formation and crack growth, prior to, and during final fracture in …

An Experimental Technique For Measurement Of Heat Generated During Bone Sawing, Hamid Khalili Parsa, Ger Reilly, Brendan Mccormack

Conference Papers

Orthopaedic bone cutting processes such as osteotomy and hip arthroplasty involve the cutting of one with the aid of various manual and powered cutting instruments including manual and powered bone saws. The extent of surgically induced bone necrosis at the point of the cutting tool and the bone is mainly due to the frictional heat generated by bone cutting. Bone necrosis has an impact on bone regeneration, and the rate of healing of the bone post operation. The threshold temperature for impaired regeneration of bone is in the range of 44°C to 47°C. Overheating also affects the sharpness life of …

Sequential Labelling And Acoustic Emission Analysis Of Damage Occurring In Cortical Bone During Indentation Cutting, Ger Reilly, Ashkan Safari, David Taylor, Brendan Mccormack

Conference Papers

When a surgeon uses a wedge shaped blade or an osteotome to cut cortical bone during an operative procedure the bone will fail by a process of microcracking and primary crack propagation. It has previously been observed that crack propagation is dependent on the direction of cutting relative to the main axis of the bone. It has also been observed that microcracks occurring during fracture release acoustic signals that facilitate real-time monitoring of a cutting process. In these novel studies, we labelled damage accumulation during cutting of cortical bone using sequential chelating dyes and we correlated recorded AE signals during …

Electromagnetic Measurement Of Spinal Curvature, Ronan Fitzmaurice, Ted Burke, Annraoi De Paor

Conference Papers

In this paper, we describe an original mathematical technique for calculating the position and orientation of an electromagnetic coil from a minimum of four collinear magnetic field measurements. This problem arose in the development of a system for evaluating the efficacy of inflatable back rafts designed to mitigate complications that arise from the immobilisation of patients with suspected spinal injuries on spinal boards during transport to hospital. Electromagnetic markers are attached to points of interest on the back of an immobilised test subject. Spinal curvature is then measured by passing a magnetometer underneath the board.

Manufacture Of Near Net Shaped 3-Dimensional Components For Industrial Applications, David Kennedy, Donal Brosnan

Conference Papers

The development of near net shape 3-Dimensional products for industrial applications has been one main goal for Manufacturing Industries over the last few decades. Processes such as polymer blow moulding and its various stages of development, glass forming, extrusion, forging, centrifugal and sand casting, bulge forming and vacuum forming are typical processes that have contributed to this development. Current practices centre on Surface coatings, Rapid Prototyping, laser forming and nanotechnology manufacture of complex 3-D shapes and assemblies. The work described in this paper is a new and highly efficient and cost effective technique for producing 3-Dimensional thin walled shapes by …

Thermal Efficiency Characteristics Of Indirect Evaporative Cooling Systems, Ben Costelloe, Donal Finn

Conference Papers

Recent developments in enhancing heat transfer in cooling towers, together with the success of chilled ceilings, have prompted a review of the evaporative cooling technique. in temperate maritime climates. The thermal efficiency of such systems is a key parameter, as a measure of the degree to which the system has succeeded in exploiting the cooling potential of the ambient air. This paper presents the results of experimental research into the thermal efficiency of a water-side open indirect evaporative cooling test rig designed to achieve low (1-4 K) approach conditions. Secondary efficiencies in the range 0.24-0.76 have been achieved.

An Investigation Of The Heat Affected Zone In Cortical Bone Sawing, Hamid Khalili Parsa, Ger Reilly, Brendan Mccormack, Andrew Macey

Conference Papers

Surgical procedures such as osteotomy and hip replacement involve the cutting of bone with the aid of various manual and powered cutting instruments including manual and powered bone saws. Frictional rubbing between the blade of the saw and the bone results in the generation of localised heating of the cut bone and increased cutting forces (Ark et al, 1997). Overheating in localised areas can cause bone necrosis and have an impact on the rate of healing of the bone post operation and overheating also affects the sharpness life of the blade. A review of the literature indicates that work has …

An Electro-Oculogram Based System For Communication And Control Using Target Position Variation, Ronan Fitzmaurice, Ted Burke, Annraoi De Paor

Conference Papers

In this paper we describe a novel mode of human computer interaction based on gaze tracking using the electro-oculogram (EOG). Despite the relative simplicity of recording this signal, it is often discounted as a reliable method of gaze tracking because of problems arising from changing sensitivity and DC drift. We describe an original technique, Target Position Variation (TPV), which addresses this issue by presenting moving icons which, when followed with the eye, create a corresponding pattern in the EOG signal which can be used to infer the correct gaze position and to compensate for variations in sensitivity.

Design Of Mobile Phone Applications For Point-Of-Care Test Result Validation., John Mcgrory, Owen Lynch, Eugene Coyle

Conference Papers

Patients with many different conditions are required to take the management of their condition into their own hands and perform Point of Care Testing (POCT) at home. However, this raises quality control issues that would not arise in a clinical setting, since the sample acquisition and testing procedures are not overseen by professional hospital staff. Another major issue, the main focus of this research, is that results from such tests are not clinically validated to ensure that they are plausible for that patient at the time of testing. In hospital, tests taken by clinicians are validated by hi-tech computerised validation …

Design Of A Wireless System For Patient-Hospital Communication And Result Validation In Point Of Care Testing, John Mcgrory, Owen Lynch, Eugene Coyle

Conference Papers

This paper discuses mobile phone (cell phone) and wireless applications for linking patients who manage their healthcare outside the hospital using Point of Care Testing (POCT) to hospital information systems (HIS). Certain medical conditions require patients to manage their healthcare by performing on themselves POC testing and act faithfully on the result. This raises quality control issue, as these POC samples and testing procedures are not independently overseen by professional hospital staff. In hospitals, samples taken by clinicians are validated by hi-tech computerised validation systems to ensure plausibility, before physicians rely on them. Patients in the home must often use …

An Acoustic Fluid-Structure Simulation Of A Therapeutic Ultrasound Wire Waveguide Apparatus, Graham Gavin, M. Hashmi, Finbar Dolan, Garret Mcguinness

Conference Papers

The use of high-power low-frequency ultrasound transmitted down small diameter wire waveguides is an emerging technology that may have potential in the treatment of complicated atherosclerotic plaques in cardiovascular surgery. This form of energy delivery results in vibrating the distal-tip of the wire waveguide disrupting material by means of direct contact ablation and also cavitation, pressure waves and acoustic streaming in the surrounding fluid. This work describes a numerical acoustic fluid-structure model of the ultrasound wire waveguide and blood surrounding the distal tip. The structural analysis of the model predicts the natural frequencies of the waveguide and shows the extent …

Development And Performance Characteristics Of An Ultrasound Angioplasty Device, Graham Gavin, Garrett Mcguinness, Finbar Dolan, M.S. J. Hashmi

Conference Papers

INTRODUCTION The effect of atherosclerosis is well documented and many procedures such as balloon angioplasty and stentimplantation have been developed to reopen occluded arteries. However, there are considerable differences in the material properties of various atherosclerotic lesions as they develop. Many authors have suggested that rigid calcified plaques may require specific procedures that target this rigid material through de-bulking or complete removal (Salunke et al, 1997). Ultrasound angioplasty is the delivery of high power low frequency ultrasound via a wire waveguide to the lesion location. This results in distal tip wire displacements of up to 100um peak-to-peak (p-p) at frequencies …

An Acoustic Fluid-Structure Simulation Of A Theraputic Ultrasound Wire Waveguide Apparatus, Graham Gavin, M.S. Hashmi, Finbar Dolan, Garrett Mcguinness

Conference Papers

The use of high-power low-frequency ultrasound transmitted down small diameter wire waveguides is an emerging technology that may have potential in the treatment of complicated atherosclerotic plaques in cardiovascular surgery. This form of energy delivery results in vibrating the distal-tip of the wire waveguide disrupting material by means of direct contact ablation and also cavitation, pressure waves and acoustic streaming in the surrounding fluid. This work describes a numerical acoustic fluid-structure model of the ultrasound wire waveguide and blood surrounding the distal tip. The structural analysis of the model predicts the natural frequencies of the waveguide and shows the extent …

Electronic Speckle Pattern Shearing Interferometry For Nondestructive Testing Of Thermal Sprayed Alloy Coatings, Qiang Xue

Conference Papers

Thermal sprayed coatings have wide engineering applications. There now exists a wide range of destructive and nondestructive testing (NDT) methods for surface coating inspections. This paper describes an application of electronic speckle pattern shearing Interferometry (ESPI) for NDT of thermal sprayed surface coatings. In contrast to other conventional methods such as eddy current,ultrasonic or X-ray, ESPSI allows fast and large survey area inspection. Experimental results of shearographic measurements are presented. Thermal sprayed coatings were tested using ESPI. Delaminations of the coatings were detected and the fringe patterns were captured using this method. It is shown that the shearography technique can …

A Gap Model For Understanding The Variation Of The Real Product From The Ideal, Kevin Delaney, Pat Phelan, Declan Delaney

Conference Papers

Clients have an idealised view of the appearance and functionality of the products they are sourcing. Their product requirements vary according to their specific circumstances and experiences. When designers try to meet or surpass client expectations, variation results and the product will deviate from the client’s idealised view. This often results in frustration, disappointment and rework for everyone concerned. Consequently designers must understand the sources of variation affecting their products and the techniques and tools that they can employ to reduce the negative effects of this variation. This paper examines the factors influencing clients as they formulate their expectations. It …

An Investigation On The Suitability Of Surface Engineered Austempered Ductile Iron As A Gear Material, M. Grech, David Kennedy, Zdravko Schauperl

Conference Papers

This preliminary study demonstrates that surface engineered austempered ductile iron is a valid alternative gear material to carburised steel. The impact energy of ductile cast iron samples in various conditions, including as – cast, austempered at 240^oC and austempered and shot peened using both 0.7mm and 1.4mm steel balls, was measured. As expected the as-cast material exhibited nominal impact energy. This has been attributed mainly to the pearlitic matrix structure.Austempering generally increases the impact energy. The extent of the improvement is however dependent on the austempering temperature and the resulting microstructure. It was shown that the structure following …

Techniques For Investigation Of Surgical Cutting Instruments, Eamon Price, Ger Reilly, Brendan Mccormack, Andrew Macey

Conference Papers

No abstract provided.