Engineering Commons^™

System Analysis Of An Internal Combustion Engine (Ice) – Solid Oxide Fuel Cell (Sofc) Hybrid Cycle, Jose Javier Colon Rodriguez

Graduate Theses, Dissertations, and Problem Reports

Due to the intermittent nature of renewable energy and the rigid operation of existing coal plants, the need for flexible power generation technology is eminent. Hybrid energy systems have shown potential for flexible, grid following dynamics while maintaining higher efficiencies. The work below focuses on the performance analysis of a proposed 100 kW pressurized Internal Combustion Engine (ICE) and Solid Oxide Fuel Cell (SOFC) hybrid system. The un-utilized fuel from the SOFC stack provided the chemical energy to operate the engine. A turbocharger was used to deliver the necessary air flow for both the stack and engine. An external reformer …

Use Of Energy Consumption During Milling To Fill A Measurement Gap In Hybrid Additive Manufacturing, K. L. M. Avegnon, P. Noll, M. R. Uddin, G. Madireddy, R. Williams, A. Achuthan, M. P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Coupling additive manufacturing (AM) with interlayer peening introduces bulk anisotropic properties within a build across several centimeters. Current methods to map high resolution anisotropy and heterogeneity are either destructive or have a limited penetration depth using a nondestructive method. An alternative pseudo-nondestructive method to map high-resolution anisotropy and heterogeneity is through energy consumption during milling. Previous research has shown energy consumption during milling correlates with surface integrity. Since surface milling of additively manufactured parts is often required for post-processing to improve dimensional accuracy, an opportunity is available to use surface milling as an alternative method to measure mechanical properties and …

Adaptable Clean Energy Laboratory, Joao Marcelo Rocha Belmonte, Marc D. Compere

Sustainability Conference

The Adaptable Clean Energy (ACE) Lab is a real-world, long term, test platform that will guide the courses of the Energy Systems track. The lab will provide realistic electrical and HVAC loads that mimic a solar powered office. The lab is a 20’ high cube shipping container modified with a door, windows, lights computers, air conditioner and appliances. The lab is Net-Zero and powered entirely from the sun. Two insulation test sections expose the exterior walls for research access to real external heat loads in a real building

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Suspended Graphene-Based Gas Sensor With 1-Mw Energy Consumption, Jong-Hyun Kim, Qin Zhou, Jiyoung Chang

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents NH₃ sensing with ultra-low energy consumption for fast recovery and a graphene sheet based on a suspended microheater. Sensitivity and repeatability are important characteristics of functional gas sensors embedded in mobile devices. Moreover, low energy consumption is an essential requirement in flexible and stretchable mobile electronics due to their small dimension and fluctuating resistivity during mechanical behavior. In this paper, we introduce a graphene-based ultra-low power gas detection device with integration of a suspended silicon heater. Dramatic power reduction is enabled by a duty cycle while not sacrificing sensitivity. The new oscillation method of heating improves …

Using The Moment Of Inertia As A Means Of Better Controlling The Speed Of Wind Turbines, Garrett L. Muhlstadt

Honors Program Projects

In the following document, the possibility of using the moment of inertia as a means of speed control for a wind turbine is explored. This document gives an introduction to wind energy and current speed control methods. This information was obtained through databases found at Benner Library. Also, an experiment was used to collect data and determine the relationship between the moment of inertia and angular velocity of a turbine. A model turbine was fabricated and powered by a fan while a Logger Pro program was used to record the angular velocity of the turbine. The moment of inertia of …

Odnawialne Źródła Energii W., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Pump Sequencing Optimization, John S. Allan, Kyle J. Nekimken, Spencer B. Weills

Mechanical Engineering

The purpose of this document is to demonstrate the design, production, and testing of optimum pump sequencing logic for variable frequency drive (VFD) pumps in commercial heating ventilating and air conditioning (HVAC) systems. The product will be developed by Pump Efficiency Solutions (PES), which is a group of Cal Poly students working on their senior project. The product is being developed for Trane, an industry leader in large scale HVAC systems. MATLAB™, Microsoft Excel, Pump System Improvement Modeling Tool™ (PSIM), and fluid mechanics hand calculations were used during software development. Next, we converted the program into Trane’s graphical programming language …

Harvesting Human Exercise Power At The Cal Poly Rec Center: Exercise Bike Power Generator Ii, Jared Rounsevell, Claire M. Shubert, Matthew Snitowsky, Andrew Wong

Mechanical Engineering

The overall goal of this project is to create a workable system to harvest the power generated on exercise bikes at the Cal Poly Rec Center so that the electricity produced can eventually be sent to the power grid. Our part of the project will focus on the mechanical harvesting of this power with the goal of using the product to run the Morningstar ProStar 12V 30 amp charge controller available from the 2007 project. Eventually, the power produced could be fed to the grid in the appropriate form. The finished result of this project should be marketable to exercise …

Novel Rotary-Turbo-Inflow Tech - Gearturbine Project - Featured Development, Carlos Barrera

Carlos Barrera

GEARTURBINE PROJECT Atypical InFlow Thermodynamic Technology Proposal Submission Novel Fueled Motor Engine Type

*State of the art Innovative concept Top system Higher efficient percent. Have similar system of the Aeolipile Heron Steam device from Alexandria 10-70 AD. -New Form-Function Motor-Engine Device. Next Step, Epic Design Change, Broken-Seal Revelation. -Desirable Power-Plant Innovation.

YouTube; * Atypical New • GEARTURBINE / Retrodynamic = DextroRPM VS LevoInFlow + Ying Yang Thrust Way Type - Non Waste Looses

-This innovative concept consists of hull and core where are held all 8 bteps of the work-flow which make the concept functional. The core has several gears …