Engineering Commons^™

Correlating Fracture Toughness And Surface Roughness For A Ductile Epoxy Adhered To Aluminum Substrates, Kurt Ryan Smith

Masters Theses

Adhesively bonded joints are used across multiple disciplines as an efficient and cost effective method for reinforcing, repairing, or creating new structures. Sufficient understanding of the bond line characteristics of the adhesive is necessary to properly design a reliable bonded joint and ensure a long service life. It is well understood that surface preparation has a significant impact on these interface characteristics as a given level of surface roughness achieves mechanical interlocking between the resin and metal and is important to prevent premature interfacial failure [1]. The goal of this study is to characterize the fracture toughness values for an …

Numerical Modeling Of Collision And Agglomeration Of Adhesive Particles In Turbulent Flows, Farzad Farajidizaji

Graduate College Dissertations and Theses

Particle motion, clustering and agglomeration play an important role in natural phenomena and industrial processes. In classical computational fluid dynamics (CFD), there are three major methods which can be used to predict the flow field and consequently the behavior of particles in flow-fields: 1) direct numerical simulation (DNS) which is very expensive and time consuming, 2) large eddy simulation (LES) which resolves the large scale but not the small scale fluctuations, and 3) Reynolds-Averaged Navier-Stokes (RANS) which can only predict the mean flow. In order to make LES and RANS usable for studying the behavior of small suspended particles, we …

Flexural Creep Behavior Of Adhesively Bonded Metal And Composite Laminates, Hasan M. Nuwayer

Wayne State University Dissertations

Adhesively bonded structures exhibit time dependent behavior when subjected to constant load (creep). In this investigation, long-term creep behavior of adhesively bonded aluminum and carbon fiber composite beams under flexural loading was investigated. Three point bending test was selected because of its simplicity and the fact that bending stresses are quite common. In this study, two types of adhesively bonded beam specimens were tested: specimens prepared by adhesively bonding two aluminum beams and specimens prepared by adhesively bonding two unidirectional carbon fiber laminated beams. Accelerated creep tests were performed at higher temperatures up to 60 °C and deflection was measured …

Mens Doped Adhesive And Influence On Fracture Toughness, Kao Z. Yang

FIU Electronic Theses and Dissertations

Composites are in high demand; however, fasteners are often required for joining process and can reduce their advantages. One solution is adhesive bonding, but uncertainty exists regarding long term durability and the ability to interrogate bonds noninvasively. One potential solution to qualify bond integrity over its service life is to dope an adhesive with magneto-electric nanoparticles (MENs). MENs can yield output magnetic signatures that are influenced by bond quality and damage state. In this study, adhesives have been doped with MENs prior to bonding at 1% volume concentration. For optimum implementation, this health monitoring system should be evaluated for effects …

Properties Of Lignin From Oil Palm Empty Fruit Bunch And Its Application For Plywood Adhesive, Lucky Risanto, Euis Hermiati, Yanni Sudiyani

Makara Journal of Technology

Lignin from lignocellulosic biomass is a potential biopolymer for wood adhesive. The aims of this study were to characterize lignin isolated from the black liquor of oil palm empty fruit bunch fiber pretreated with steam explosion in alkaline conditions and to examine the bond quality of aqueous polymer isocyanate (API) adhesive prepared from lignin, natural rubber latex (NRL), and polyvinyl alcohol (PVA) as base polymers with isocyanate crosslinkers. Lignin was precipitated from the black liquor by adding hydrochloric acid; then the precipitate was separated by filtration, thoroughly washed with water up to pH 2 and pH 5, and dried. The …

Direct Verification Of The Locking Of Liquid Locking Compounds In Threaded Fasteners, Ryan Hunter

USF Tampa Graduate Theses and Dissertations

The motivation of this research is to explore the viability of a method to directly verify whether or not an anaerobic adhesive within a threaded fastener assembly has cured sufficiently to provide secondary locking. Direct verification was implemented via the application of a test torque in the loosening direction of a fastener assembly with Loctite (given a 24 hour cure time). A three phase test plan was developed with the intent of identifying and utilizing this verification torque value which is unique to a given fastener assembly.

It was proved that the direct verification method, as outlined in the test …