Engineering Commons^™

Quantification Of The Effect Of Tool Geometric Features On Aspects Of Friction Stir Welding, Md. Reza-E-Rabby

Theses and Dissertations

In the friction stir welding (FSW) process, tool stirring and synchronized movement of the weld materials along a pre-existing seam line causes thermal gradients and severe plastic deformation resulting in the bonding of the adjacent materials. For a given set of welding parameters, tool pin geometries (dimensions, shape) and vertical/helical features that dictate the material motion also have significant effects on process response variables during FSW. Among the primary process controlling parameters in FSW, tool pin geometry and feature vary multifariously in terms of shape, dimensions, feature insertion technique depending on the weld material and application of joint. The current …

Ultrafine Particle Generation And Measurement, Qiaoling Liu

Theses and Dissertations

Ultrafine particles (UFPs) with diameters smaller than 100 nm are omnipresent in ambient air. They are important sources for fine particles produced through the agglomeration and/or vapor condensation. With their unique properties, UFPs have also been manufactured for industrial applications. But, from the toxicological and health perspective, ultrafine particles with high surface-to-volume ratios often have high bio-availability and toxicity. Many recent epidemiologic studies have evidence UFPs are highly relevant to human health and disease. In order to better investigate UFPs, better instrumentation and measurement techniques for UFPs are thus in need. The overall objective of this dissertation is to advance …

Generation And Delivery Of Charged Aerosols To Infant Airways, Landon T. Holbrook

Theses and Dissertations

The administration of pharmaceutical aerosols to infants on mechanical ventilation needs to be improved by increasing the efficiency of delivery devices and creating better ways of evaluating potential therapies. Aerosolized medicines such as surfactants have been administered to ventilated infants with mixed results, but studies have shown improvement in respiratory function with a much lower dose than with liquid instillation through an endotracheal tube (ETT). An aerosolized medicine must be transported through the ventilation tubing and deposit in the lungs to have the desired therapeutic response.

This work has taken a systematic approach to (i) develop new devices for the …

A Study To Evaluate Non-Uniform Phase Maps In Shape Memory Alloys Using Finite Element Method, Naren Motte

Theses and Dissertations

The unique thermo-mechanical behavior of Shape Memory Alloys (SMAs), such as their ability to recover the original shape upon heating or being able to tolerate large deformations without undergoing plastic transformations, makes them a good choice for actuators.

This work studies their application in the aerospace and defense industries where SMA components can serve as release mechanisms for gates of enclosures that have to be deployed remotely. This work provides a novel approach in evaluating the stress and heat induced change of phase in a SMA, in terms of the transformation strain tensor. In particular, the FEA tool

ANSYS has …

Micro- And Macro-Scale Modeling Of Filter Aging: Effects Of Particle Poly-Dispersity And Fiber Cross-Sectional Shape, Ahmed M. Saleh

Theses and Dissertations

The goal of this study is to further advance the state of the art in developing self-sufficient methods to predict the performance of an aerosol filter. The simulation methods developed in this study are based on first principles and consequently, they do not rely on empirical correction factors. These simulation methods can be used to predict the instantaneous collection efficiency and pressure drop of a filter under dust-loading conditions. In the current study, 3-D micro- and macroscale CFD models are developed to simulate the service life of flat-sheet and pleated filters. These CFD micro- and macroscale models are also used …

Computational Modeling To Assess Surgical Procedures For The Treatment Of Adult Acquired Flatfoot Deformity, Brian A. Smith

Theses and Dissertations

Several surgically corrective procedures are considered to treat Adult Acquired Flatfoot Deformity (AAFD) patients, relieve pain, and restore function. Procedure selection is based on best practices and surgeon preference. Recent research created patient specific models of Adult Acquired Flatfoot Deformity (AAFD) to explore their predictive capabilities and examine effectiveness of the surgical procedure used to treat the deformity. The models’ behavior was governed solely by patient bodyweight, soft tissue constraints, and joint contact without the assumption of idealized joints. The current work expanded those models to determine if an alternate procedure would be more effective for the individual. These procedures …

Methods For Determining Grease Service Levels In An Ah-64d Intermediate Gearbox Using On-Board Sensors, Travis Steven Edwards

Theses and Dissertations

The intermediate gearbox (IGB) on the AH-64D was chosen as the subject for this study based on the persistent grease leaks that require grounding aircraft. The aircraft is not currently equipped with a method of detecting grease loss during flight, so techniques for analyzing the usefulness of old metrics and possible new techniques can be tested. The main objective of this study is to use the aircraft’s on-board sensors to develop a method of determining the lubrication level of the IGB. Currently, the most reliable method for detecting a fault on the aircraft is through the use of vibration-based condition …

Design Of Experiments Analysis Of Non-Standard Inputs For The Optimization Of Friction Stir Welding, Ryan Widejko

Theses and Dissertations

The purpose of this study was to use non-standard Design of Experiments (DoE) inputs in Friction Stir Welding (FSW) to deduce relationships between various weld input and response variables. Typically, inputs for FSW DoE are tool rotational speed, welding speed and forge force. In this study, three different input factors were investigated: travel speed, thermal boundary conditions (TBC), and advance per revolution (APR). The experimental design included a full factorial with each factor at two levels plus two centerpoint runs. Response variables included weld temperature, microstructure, hardness, power, weld energy, and in plane forces.

An investigation of the effect of …

Fabrication And Characterization Of Anode-Supported Micro-Tubular Solide Oxide Fuel Cell By Phase Inversion Method, Cong Ren

Theses and Dissertations

Nowadays, the micro-tubular solid oxide fuel cells (MT-SOFCs), especially the anode supported MT-SOFCs have been extensively developed to be applied for SOFC stacks designation, which can be potentially used for portable power sources and vehicle power supply. To prepare MT-SOFCs with high electrochemical performance, one of the main strategies is to optimize the microstructure of the anode support. Recently, a novel phase inversion method has been applied to prepare the anode support with a unique asymmetrical microstructure, which can improve the electrochemical performance of the MT-SOFCs. Since several process parameters of the phase inversion method can influence the pore formation …

Predictive Methods For End Of Life Prognosis In Composites, Vamsee Vadlamudi

Theses and Dissertations

The long-term properties of continuous fiber reinforced composite materials are increasingly important as applications in airplanes, cars, and other safety critical structures are growing rapidly. The mechanical, electrical, and thermal properties of composite materials are altered by the initiation and accumulation of discrete fracture events whose distribution and eventual interaction defines the limits of design, such as strength and life. There is a correlation that exists between the long term behavior of those materials under combined mechanical, thermal, and electrical fields, and the functional properties and characteristics of the composite materials that requires a fundamental understanding of the material state …