Engineering Commons^™

Static And Dynamic Response Of Silty Toyoura Sand With Pva Fibre And Cement Additives, Colin J.R. Schmidt

Electronic Thesis and Dissertation Repository

After the Great East Japan Earthquake of 2011, nearly 24 million tons of disaster debris such as concrete products, natural and polymeric fibres, and tsunami deposits remained on the coast of Japan. Much of this debris was recycled and repurposed in engineering projects such as embankments, park restoration, and agricultural field restoration around Tokyo Bay, one of the hardest hit regions of the country. Such a major disaster developed a need for the stabilization of the liquefaction susceptible regions of the reclaimed Tokyo Bay coastline. This thesis specifically focuses on the stabilization against liquefaction of Toyoura sand with the typical …

Wind And Thermal Effects On Ground Mounted Photovoltaic (Pv) Panels, Chowdhury Mohammad Jubayer

Electronic Thesis and Dissertation Repository

A combination of Computational Fluid Dynamics (CFD) simulations and wind tunnel experiments are carried out to investigate the effects of wind on the aerodynamic loading and heat transfer of a ground mounted stand-alone photovoltaic (PV) panel with tilt angle of 25^o in open country atmospheric boundary layer. Several azimuthal wind directions are considered: Southern 0^o, Southwest 45^o, Northwest 135^o and Northern 180^o. Three dimensional Reynolds-Averaged Navier-Stokes (RANS) approaches with an unsteady solver using Shear Stress Transport (SST) k-ω turbulence closure are employed for the CFD simulations, whereas Particle Image Velocimetry (PIV) and …

Influence Of Water Chemistry Parameters On The Dissolution Rate Of The Lead (Ii) Carbonate Hydrocerussite, Caitlin Se Kushnir

Electronic Thesis and Dissertation Repository

This work has focused on the kinetic dissolution of the lead (II) carbonate hydrocerussite (Pb₃(CO₃)₂(OH)₂) under four pH conditions (7.5, 8, 9, 10), three dissolved inorganic concentrations (DIC; 10, 20, 50 mg C/L), and three initial hydrocerussite concentrations (10, 20, 50 mg/L) in batch experiments. Experiments were performed in at least duplicate to determine total dissolved lead dissolution curves at short time scales (hr.). All equilibrium dissolved lead concentrations were achieved in 40 minutes or less, and matched trends from previous studies; pH 7.5 and pH 10 corresponding to the highest and …

Wind-Induced Pressures In Air Permeable, Double-Layer Roof Systems In Regions Of Separated Flow, Jeong Hee Oh

Electronic Thesis and Dissertation Repository

This thesis is concerned with the wind-induced pressure distribution acting on air permeable, double-layer roof systems placed on low-rise buildings. Because of the pressure transmission into the cavity between layers, the pressure difference in the double-layer systems differs significantly from that in a single layer. The interior pressures (in the cavity between layers) are highly correlated with external pressures at the openings on the external surface of the outer layer and thereby, the net wind load for the design of the outer layer is considerably reduced by the pressure equalization between the external and internal surfaces of the outer layer. …

Probabilistic Modeling And Bayesian Inference Of Metal-Loss Corrosion With Application In Reliability Analysis For Energy Pipelines, Hao Qin

Electronic Thesis and Dissertation Repository

The stochastic process-based models are developed to characterize the generation and growth of metal-loss corrosion defects on oil and gas steel pipelines. The generation of corrosion defects over time is characterized by the non-homogenous Poisson process, and the growth of depths of individual defects is modeled by the non-homogenous gamma process (NHGP). The defect generation and growth models are formulated in a hierarchical Bayesian framework, whereby the parameters of the models are evaluated from the in-line inspection (ILI) data through the Bayesian updating by accounting for the probability of detection (POD) and measurement errors associated with the ILI data. The …

Response Of Transmission Line Conductors Under Downburst Wind, Haitham Aboshosha

Electronic Thesis and Dissertation Repository

Electricity is transmitted by Transmission Lines (TLs) from the source of production to the distribution system and then to the end consumers. Failure of a TL can lead to significant economic losses and to negative social consequences resulting from the interruption of power. High Intensity Winds (HIW), in the form of downbursts and tornadoes, are believed to be responsible for more than 80% of the weather-related failure of TLs around the world. The studies reported in this thesis are part of an ongoing extensive research program at Western University focusing on the response of TLs under HIW. Previous investigations conducted …

Physical Sulphate Attack On Concrete, Ahmed Ramadan Suleiman

Electronic Thesis and Dissertation Repository

Field experience with concrete exposed to sulphates has often shown that concrete can suffer from surface scaling above the ground level caused by physical sulphate attack. This type of attack has been ignored and, in some instances, confused with chemical sulphate attack. In addition, current standards that evaluate the performance of concrete under sulphate attack, only deal with the chemical aspects of sulphate attack. This lack of information has led to confusion and contradictory views regarding the mechanisms of concrete deterioration due to physical sulphate attack. In the current thesis, the performance of concrete exposed to environments prone to physical …

Full-Scale Tests Of A Wood-Frame Structure Under Extreme Wind Loads, Derek A. Stedman

Electronic Thesis and Dissertation Repository

Tornadoes can produce some of the strongest winds on earth; these highly localized storms can cause massive damage. Assessments of tornado wind speeds are done using post-event observations of damage via the Enhanced Fujita Scale.

A very commonly observed failure occurs at the roof-to-wall connection where the roof breaks up or flies away, typically leaving the walls in place. However, once the roof is gone the walls are more vulnerable to the wind. If a wall subsequently fails, it increases the risk of injury or death for occupants. Significant research has been done for failures of roof-to-wall connections and roof …

Shear Capacity Of Reinforced Concrete Beams At Elevated Temperatures, Mohamed Diab

Electronic Thesis and Dissertation Repository

Fire safety is an important design aspect that ensures structural integrity of a Reinforced Concrete (RC) building during fire events. As new codes are moving from prescriptive methods to performance-based methods, design engineers are in need of rational design tools to assess the capacity of RC elements during a fire event. Previous research work focused on the flexural and axial capacities of concrete elements exposed to fire. Research addressing the shear capacity of concrete elements exposed to fire is limited in the literature.

An analytical method to predict the shear capacity of RC beams exposed to elevated temperatures is proposed. …

Structural And Durability Performance Of Precast Segmental Tunnel Linings, Safeer Abbas

Electronic Thesis and Dissertation Repository

The use of precast concrete tunnel linings (PCTLs) has been escalating due to its efficient and economical installation process compared to that of normal cast in-situ lining practice. Normally, PCTL segments are designed for 100 years of service life. However, tunnel structures often suffer premature degradation primarily due to reinforcement corrosion, which requires costly repair and maintenance. Hence, addressing and solving such durability-sustainability dilemma of tunnels is a must. The main aim of this dissertation is to evaluate the structural and durability performance of full-scale conventional reinforced concrete (RC) PCTL segments in comparison to steel fibre-reinforced concrete (SFRC). Moreover, the …

Numerical Modelling Of Downburst Interaction With Bluff Body, Aditi Jog

Electronic Thesis and Dissertation Repository

The objective of this study is to investigate the interaction of a bluff body with a downburst flow. Numerical investigation of the flow field using CFD analysis was carried out for three different downburst sizes (h/d=1, 2, 4) under suitable boundary conditions subjected to constant jet velocity. The downburst-structure interaction study was conducted for two jet diameters (h/d=1 and 4) and two radial locations from the downburst center.

The results showed that the downburst size greatly dominates the intensity of the flow. The largest downburst resulted in the highest velocity magnitude near the ground and also covered a larger area …

Hydrogeological And Thermal Sustainability Of Geothermal Borehole Heat Exchangers, S. Emad Dehkordi

Electronic Thesis and Dissertation Repository

Assessment of the current approach taken by guidelines and design methods of vertical closed loop heat exchangers shows that often groundwater flow is either disregarded or is not methodically incorporated. The state of scientific research in this arena reveals that overlooking the groundwater flow in the design procedure may not always be a correct assumption. The significance of advective heat transport compared to conduction is defined by the groundwater flux or Darcy velocity which heavily depends on the hydraulic conductivity of the ground, followed by the hydraulic gradient which has a relatively limited range. A sensitivity analysis on ground and …

Numerical Evaluation Of Aerodynamic Roughness Of The Built Environment And Complex Terrain, Daniel S. Abdi

Electronic Thesis and Dissertation Repository

Aerodynamic drag in the atmospheric boundary layer (ABL) is affected by the structure and density of obstacles (surface roughness) and nature of the terrain (topography). In building codes and standards, average roughness is usually determined somewhat subjectively by examination of aerial photographs. For detailed wind mapping, boundary layer wind tunnel (BLWT) testing is usually recommended. This may not be cost effective for many projects, in which case numerical studies become good alternatives. This thesis examines Computational Fluid Dynamics (CFD) for evaluation of aerodynamic roughness of the built environment and complex terrain.

The present study started from development of an in-house …

Finite Element Analyses Of Single-Edge Bend Specimens For J-R Curve Development, Yifan Huang

Electronic Thesis and Dissertation Repository

The fracture toughness resistance curve such as the J-integral resistance curve (J-R curve) is widely used in the integrity assessment and strain-based design of energy pipelines with respect to planar defects (i.e. cracks). Two studies about the development of the J-R curve are carried out and reported in this thesis. In the first study, the plastic geometry factor, i.e. the η_pl factor, used to evaluate J in a J-R curve test based on the single-edge bend (SE(B)) specimen is developed based on the three-dimensional (3D) finite element analysis (FEA). The main …

Effect Of Instantaneous Load Eccentricities On The Inelastic Torsional Responses Under Bi-Directional Seismic Excitations, Xiaojing Cui

Electronic Thesis and Dissertation Repository

This study evaluated the inelastic torsional response due to instantaneous load eccentricities. The load eccentricities, which caused by the motion of the center of mass are time-dependent, even exist for two-way symmetric structures under seismic excitations. The eccentricities and bi-directional horizontal excitations can lead to the torsional motion. The study of the impacts of such a second-order effect (called A-Delta effect) on structural systems and, this effect in combination with the P-Delta effect on structural systems has not been reported in the literature.

This study is focused on the investigation of the structural responses under the A-Delta …

Calibration Of Fatigue Design Wind Pressure For Sign, Luminaire, And Traffic Signal Support, Guigui Zu

Electronic Thesis and Dissertation Repository

The study is focused on calibration of fatigue design wind pressure for sign, luminaire and traffic signal support under natural and truck-induced wind gusts. The design of the support structures in Canada is governed by the current Canadian Highway Bridge Design Code (CHBDC). However, the code is not specific on the fatigue design wind pressure (natural or truck-induced) for these structures. Although there are equivalent static natural and truck-induced wind pressures for fatigue design recommended in the provisions of the American Association of State Highway and Transportation Officials (AASHTO), none of relevant studies discussed the implied reliability by using these …

A System Dynamics Approach To Water Resources And Food Production In The Gambia, Jordan T. Atherton

Electronic Thesis and Dissertation Repository

The Gambia, a country in West African, faces an increasingly daunting situation. They do not produce enough food needed to feed the population, yet population growth remains high, and the current area of land under cultivation is approaching total arable land available. Climate changes complicate matters further as the majority of farms lack irrigation and are dependent on rainfall to provide water to their crops. The purpose of this thesis is to provide the first 1st iteration of a system dynamics model that could be useful as a tool to assist decision in the Gambia better understand long-term implications of …

Biofilm Control In A Fludized Bed Bioreactor (Fbbr) Treating Municipal Wastewater: Optimization, Modeling, And Nitrous Oxide (N2o) Emissions, Ahmed Eldyasti

Electronic Thesis and Dissertation Repository

Among the various biological wastewater treatment processes for industrial and municipal wastewater treatment, fluidized bed bioreactors (FBBR) demonstrate numerous advantages compared to suspended growth systems such as lower hydraulic retention time, high surface area and accordingly high biomass retention time, higher volumetric conversion rates, lower sensitivity to temperature, and less sludge production. Despite the numerous biofilm bioreactor configurations and system schemes that are currently available for a wide variety of environmental applications, the development and optimization of a stable biofilm that is capable of offering effective and integrated functions, i.e. biodegradation, biomass-liquid separation, and biomass retention along with a substantial …

Experimental Investigation Of Wind Effect On Solar Panels, Ayodeji Abiola-Ogedengbe

Electronic Thesis and Dissertation Repository

Photovoltaic Solar Panels for electricity generation are outdoor low-rise structures that are vulnerable to damage by the wind. The existing building codes do not contain information about the impact of the wind on these structures and hence do not provide comprehensive guidelines to mitigate such impact. The present study is a contribution to the ongoing efforts to codify the wind loading on solar panels. In this study, experimental investigations were conducted on the scaled model of a ground-mounted solar panel structure whose surface is geometrically similar to an inclined flat plate and mounted on three-legged support. The panel comprises of …

Wind Field Measurements Around Photovoltaic Panel Arrays Mounted On Large Flat-Roofs, R Nicolas Pratt

Electronic Thesis and Dissertation Repository

An investigation of the wind field around roof-mounted PV arrays has been undertaken, utilizing synchronized TR-PIV and pressure measurements, in order to better understand the mechanisms which result in the aerodynamic loads, most importantly uplift, which act on such arrays. The mean flow is not significantly altered above the array as compared to a bare roof, while Reynolds normal and shear stresses are markedly reduced. Increasing the tilt angle of the array results in a progression from uplifts driven by vortex induced suction, which cause peak uplifts on a bare roof, towards uplifts which are driven primarily by local flow …

Monotonic And Cyclic Behaviour Of Steel Fibre-Reinforced And Frp-Steel Fibre-Reinforced Helical Pulldown Micropiles, Mahmoud Meckkey M. El Sharnouby

Electronic Thesis and Dissertation Repository

Helical piles are a deep foundation system that can be used to support pipelines, telecommunication and transmission towers, and low- and medium-rise buildings. Advantages of helical piles include: short installation time with minimal noise and vibration levels; can be installed with ease in limited accessibility site; and onsite quality control by measurement of installation torque.

The main objective of the current research is to assess the performance of steel fibre-reinforced helical pulldown micropiles (RHPM), and fibre-reinforced polymer-steel fibre- reinforced pulldown micropiles (FRP-RHPM) under axial and lateral monotonic and cyclic loading conditions.

The research methodology involved conducting full scale field testing …

Load-Sharing Of Toe-Nailed, Roof-To-Wall Connections Under Extreme Wind Loads In Wood-Frame Houses, Mohammad Khan

Electronic Thesis and Dissertation Repository

A typical wood frame house roof consists of trusses which are nailed to the top-plates of the wall assembly. These are known as roof-to-wall connections (RTWCs). A load-sharing mechanism is developed between adjacent RTWCs via roof elements such as roof-sheathing, fascia beams, etc., during high wind loads. An experimental setup was developed to observe the load-sharing behavior between seven connections. To mimic the roof bending stiffness in the direction perpendicular to the trusses, two steel beams with representative bending stiffness were connected across the RTWCs in a simple way. Identical ramp and identical fluctuating wind loads were applied to all …

Consistent Density Scanning And Information Extraction From Point Clouds Of Building Interiors, Kuldeep Kumar Sareen

Electronic Thesis and Dissertation Repository

Over the last decade, 3D range scanning systems have improved considerably enabling the designers to capture large and complex domains such as building interiors. The captured point cloud is processed to extract specific Building Information Models, where the main research challenge is to simultaneously handle huge and cohesive point clouds representing multiple objects, occluded features and vast geometric diversity. These domain characteristics increase the data complexities and thus make it difficult to extract accurate information models from the captured point clouds.

The research work presented in this thesis improves the information extraction pipeline with the development of novel algorithms for …

A Study On The Turbulent Characteristics Within The Hurricane Boundary Layer, Sunwei Li

Electronic Thesis and Dissertation Repository

As the medium between the sea surface and the upper atmosphere in a hurricane, the Hurricane Boundary Layer (HBL) plays a key role in the overall dynamics of a tropical cyclone, and therefore turbulence exchanges within the HBL deserve a thorough investi- gation. However, since it is dangerous and difficult to take direct measurements within the HBL, studies of the HBL turbulence processes based on direct observations are rare. Thanks to the newly developed dropwindsonde equipped with a Global Position System (GPS) receiver, it is now possible to measure wind velocities and other meteorological variables with an unprecedented accuracy and …

Enhancement Of Local Buckling Behaviour Of Steel Structures Retrofitted Through Bonding Gfrp Plates, Mohammad Al Amin Siddique

Electronic Thesis and Dissertation Repository

An effective technique involving the use of glass fiber reinforced polymer (GFRP) plates to enhance the local buckling behaviour of steel plates, beams, and moment resisting frames is presented in this Thesis. The enhancement in buckling capacity is achieved by bonding GFRP plates to the steel sections. These steel/GFRP joints have the advantages of ease of application, low cost, high strength-to-weight ratio, and resistance to corrosion. An interface element that simulates the behaviour of the adhesive bonding the steel and GFRP elements is developed and is implemented into an in-house developed finite element model to represent steel/GFRP joints. The model …

Investigation Of Bio-Hydrogen And Bio-Methane Production From Thin Stillage, Noha El-Sayed Nasr

Electronic Thesis and Dissertation Repository

An evaluation of single-stage and two-stage anaerobic digestion processes for biomethane and biohydrogen production using thin stillage was performed to assess the viability of biohydrogen production from thin stillage and the impact of separating the acidogenic and methanogenic stages on anaerobic digestion with hydrogen production in the first stage. A comparative evaluation of anaerobic digester sludge (ADS) and acclimatized anaerobic digester sludge (AADS) for biohydrogen production was performed at various S°/X° ratios. The optimum range of S°/X° ratio for hydrogen production was found to be 1 to 2 gCOD/gVSS using conventional ADS and 3 to 6 gCOD/gVSS using AADS. Maximum …

Seismic Microzonation Of Great Toronto Area And Influence Of Building Resonances On Measured Soil Responses, Dimitar Genchev Mihaylov

Electronic Thesis and Dissertation Repository

A pilot seismic microzonation of the Greater Toronto Area (GTA) is used to establish the conditions and limitations of geophysical methods for site response investigations in city conditions. Maps of fundamental soil resonant frequencies, amplifications at these frequencies and interpolated average shear wave velocity of top 30 m of soil profile (VS- 30) used in soil classification were compared to the maps of drift thickness and surficial geology for the GTA. The non-applicability of the interpolated VS-30 map for site classification between measured test points is indicated. It is also shown that the soil response cannot be estimated properly using …

Vortex Shedding From Elongated Bluff Bodies, Zachary J. Taylor

Electronic Thesis and Dissertation Repository

As the spans of suspension bridges increase, the structures become inherently flexible. The flexibility of these structures, combined with the wind and particular aerodynamics, can lead to significant motions. From the collapse due to flutter of the Tacoma Narrows Bridge to the case of vortex-induced vibrations (VIV) of the Storebælt Bridge, it is evident that a better understanding of the aerodynamics of these geometries is necessary. The work herein is motivated by these two problems and is presented in two parts.

In the first part, the focus is on the physical mechanisms of vortex shedding. It is shown that the …

Experimental And Numerical Development Of Anchor-Jointed Precast Structural Wall System And Optimum Design Of Prestressed Slabs, Mohamed El Semelawy

Electronic Thesis and Dissertation Repository

Precast concrete shear walls are used to resist lateral loads in low- to medium-rise buildings. An innovative joining technique is proposed to accelerate construction process and to reduce concrete damage possibility and capital loss during an earthquake event. Panels are jointed using steel anchor bolts, therefore, the system is designated "anchor-jointed precast structural wall system". In this system, anchors are utilized as a structural fuse. Damaged anchors are easily replaced after an earthquake, thus minimizing repair costs and serviceability disruptions. In the first part of this thesis, conceptual development of the system is carried out. A research program of combined …

Investigation On Rheology Of Oil Well Cement Slurries, Anjuman Shahriar

Electronic Thesis and Dissertation Repository

The rheology of OWC slurries is generally more complicated than that of conventional cement paste. In order to contend with bottom hole conditions (wide range of pressure and temperature), a number of additives are usually used in the OWC slurries and the slurry shows different characteristics depending on the combination of admixture used. The objective of this research is to develop a fundamental understanding on the important mechanisms that affects the rheology of cement slurry incorporating various chemical and mineral admixtures. The thesis aimed at developing cement slurries by partial replacement of oil well cement using different mineral admixtures, offering …