Oil, Gas, and Energy Commons^™

Time-Dependent Crack Growth Behavior Of Alloy 617 And Alloy 230 At Elevated Temperatures, Shawoon Kumar Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

Two Ni-base solid-solution-strengthened superalloys: INCONEL 617 and HAYNES 230 were studied to check sustained loading crack growth (SLCG) behavior at elevated temperatures appropriate for Next Generation Nuclear Plant (NGNP) applictaions with constant stress intensity factor (K _max = 27.75 MPa[checkmark]m) in air. The results indicate a time-dependent rate controlling process which can be characterized by a linear elastic fracture mechanics (LEFM) parameter - stress intensity factor (K). At elevated temperatures, the crack growth mechanism was best described using a damage zone concept. Based on results and study, SAGBOE (stress accelerated grain boundary oxidation embrittlement) is considered the primary reason for …

Computational Study Of Passive Neutron Albedo Reactivity (Pnar) Measurement With Fission Chambers, Sandra De La Cruz

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Passive Neutron Albedo Reactivity technique (PNAR) was used to assay used nuclear fuel as a potential method for the measurement of fissionable material in fuel assemblies. A Monte Carlo transport code (MCNPX 2.6) was used to develop simulation models to evaluate the PNAR technique. The MCNPX simulated models consisted of two 17x17 Pressurized Water Reactor (PWR) used fuel assemblies; one with an initial 3 wt% uranium-235*, cooled for 20 years and second with an initial 4 wt% uranium-235*, cooled for 5 years. Each used fuel assembly was simulated at four different burn up rates of 15, 30, 45, and …

Long Term Outdoor Testing Of Low Concentration Solar Modules, Lewis Fraas, James Avery, Leonid Minkin, H. X. Huang, Tim Hebrink, Robert F. Boehm

Mechanical Engineering Faculty Research

A 1‐axis carousel tracker equipped with four 3‐sun low‐concentration mirror modules has now been under test outdoors at the University of Nevada in Las Vegas (UNLV) for three years. There are three unique features associated with this unit. First, simple linear mirrors are used to reduce the amount of expensive single crystal silicon in order to potentially lower the module cost while potentially maintaining cell efficiencies over 20% and high module efficiency. Simple linear mirrors also allow the use of a single axis tracker. Second, the azimuth carousel tracker is also unique allowing trackers to be used on commercial building …

Measuring Progress With Normalized Energy Intensity, Nathan Lammers, J. Kelly Kissock, Brian Abels, Franc Server

Mechanical and Aerospace Engineering Faculty Publications

Energy standard ISO 50001 will require industries to quantify improvement in energy intensity to qualify for certification. This paper describes a four-step method to analyze utility billing, weather, and production data to quantify a company's normalized energy intensity over time. The method uses 3-pararameter change-point regression modeling of utility billing data against weather and production data to derive energy signature equations. The energy signature equation is driven by typical weather and production data to calculate the 'normal annual consumption', NAC, and divided by typical production to calculate 'normalized energy intensity' NEI. These steps are repeated on sequential sets of 12 …

Improving Compressed Air Energy Efficiency In Automotive Plants: Practical Examples And Implementation, Nasr Alkadi, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

The automotive industry is the largest industry in the United States in terms of the dollar value of production [1]. U.S. automakers face tremendous pressure from foreign competitors, which have an increasing manufacturing presence in this country. The Big Three North American Original Equipment Manufacturers (OEMs)-General Motors, Ford, and Chrysler-are reacting to declining sales figures and economic strain by working more efficiently and seeking out opportunities to reduce production costs without negatively affecting the production volume or the quality of the product. Successful, cost-effective investment and implementation of the energy efficiency technologies and practices meet the challenge of maintaining the …

Investigation On Flame Characteristics Of Oxy-Fuel Combustion, Md R. Islam

Open Access Theses & Dissertations

Oxy-fuel combustion is currently being considered by the U.S Department of Energy as a promising technology for efficient carbon capture. This technology could substantially reduce NOx and CO2 emissions. In addition, the implementation of oxy-fuel combustion technology in a power generation system could potentially reduce negative environmental impacts of fossil fuel use. It also encourages the use of reliable and domestic energy sources. The U.S. Department of Energy has made efforts to investigate the performance of a CO2 and H2O diluted oxy-fuel combustion system in a high-pressure combustor. In an effort to better understand and characterize the fundamental flame characteristics …

Experimental And Numerical Investigation Of The Effect Of Fuel Composition On Flame Stability On A Gas Turbine Combustor, Gilberto Corona

Open Access Theses & Dissertations

Gas turbines are used for power generation and aviation all over the world. Fossil fuels remain the main source of energy for the operation of gas turbines but the recent increase in environmental awareness has influenced government agencies to impose stringent limits on pollutant emissions from power generation plants. Pollutant emissions control is one of the major challenges for gas turbine designers. In this study, experimental methods and computational fluid dynamics (CFD) technologies are used to study the problems that arise when coal derived fuels are used in Gas Turbine Combustors.

Gas turbine designers need both experimental data and combustion …

User's Guide To Mbc3: Multi-Blade Coordinate Transformation Code For 3-Bladed Wind Turbine, G. S. Bir

Publications (E)

The dynamics of wind turbine rotor blades are conventionally expressed in rotating frames attached to the individual blades. The tower-nacelle subsystem though, sees the combined effect of all rotor blades, not the individual blades. Also, the rotor responds as a whole to excitations such as aerodynamic gusts, control inputs, and tower-nacelle motion—all of which occur in a nonrotating frame. Multi-blade coordinate transformation (MBC) helps integrate the dynamics of individual blades and express them in a fixed (nonrotating) frame. MBC involves two steps: transforming the rotating degrees of freedom and transforming the equations of motion. Reference 1 details the MBC operation. …

Wind Flow Modeling For Wind Energy Analysis Of The Nellis Dunes Area In Nevada, Upendra Rangegowda

UNLV Theses, Dissertations, Professional Papers, and Capstones

A wind energy analysis of the Nellis Dunes area in Nevada was conducted. A DEM file which contains the elevation data was used to generate the surface model and to create a 3-D mesh of the region. Local meteorological tower data collected for a period of one year was used to generate the diagnostic initial wind fields. Upper level wind fields were created using a surface boundary layer technique along with linear interpolation of the tower level wind fields. The vertical components of the velocities were adjusted using the equation of continuity. Mass consistent 3-D wind fields were then calculated …

Hydrogen Separation Membranes, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Technical brief describing hydrogen separation membranes and their potential to reduce cost of hydrogen production and CO₂ separation. Outlines membrane types, commercially available membranes, and new technological developments. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]

Solar Power And The Electric Grid, Energy Analysis, Nrel Energy Analysis

Publications (E)

In today’s electricity generation system, different resources make different contributions to the electricity grid. This fact sheet illustrates the roles of distributed and centralized renewable energy technologies, particularly solar power, and how they will contribute to the future electricity system. The advantages of a diversified mix of power generation systems are highlighted.

Nrel: A Year In Clean Energy Innovations: A Review Of Nrel's Feature Stories, National Renewable Energy Laboratory

Publications (E)

The National Renewable Energy Laboratory (NREL) is the nation’s primary laboratory for renewable energy and energy efficiency research and development.

NREL’s mission and strategy are focused on advancing the U.S. Department of Energy’s and our nation’s energy goals. The laboratory’s scientists and researchers support critical market objectives to accelerate research from scientific innovations to market-viable alternative energy solutions. At the core of this strategic direction are NREL’s research and technology development competencies. These areas span from understanding renewable resources for energy, to the conversion of these resources to renewable electricity and fuels, and ultimately to the use of renewable electricity …

College Of Engineering Senior Design Competition Fall 2009, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Each student in his or her senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. The senior design project encourages the student to use everything learned in the engineering program to create a practical, real-world solution to an engineering challenge.

A highlight of the year-long senior design project is the senior design competition. This competition, which usually takes place the week before finals each semester, helps focus the senior students on increasing the quality and potential for commercial application for their design projects.

Judges from local industry evaluate the projects on innovation, commercial …

National Center For Hydrogen Technology, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Brochure about the Energy & Environmental Research Center's National Center for Hydrogen Technology. Includes its role in developing technologies that produce and utilize hydrogen. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]

The Very Basics Of Sustainability - An Alternative Viewpoint (Slides With Audio) (Large File! To Speed Up Download, Right-Click On "Download" Link To Save To Own Pc.), Jim Mcgovern

Other resources

This presentation sets out the very basics of ‘sustainability’, although a definition of sustainability is not attempted. Some of the very basics are the context in which the Earth and humankind exist in space and time, the Earth’s climate, the Earth’s population and humankind’s options and choices. The author advocates keeping an open mind on all available options, including the use of oil, gas, coal, tar sands, carbon capture and sequestration, nuclear power etc., as well as the technologies that are more widely considered ‘green’. The author also argues that, in addressing the challenges that humankind faces, globally concerted effort …

An Experimental Study Of The Hydrodynamics Of Multiphase Flow In Fluidized Beds, Gerardo Vargas

Open Access Theses & Dissertations

Fluidized bed reactors have been widely used as a gasifier in coal gasification processes to convert coal into other forms of energy. At this stage, full fluidization is required to attain the best thermochemical reaction within the fluid-solid mixture. This can only be achieved if the fluid is maintained between minimum fluidization and terminal velocities. To better understand the hydrodynamics of multiphase flow, a fluidized bed was designed and constructed to carry out the investigation. Compressed air and 1-mm glass beads were used to determine gas minimum fluidization and terminal velocities at three different particle concentrations. The solids were enclosed …

Optimization Of Channel Geometry In A Proton Exchange Membrane (Pem) Fuel Cell, Jephanya Kasukurthi

UNLV Theses, Dissertations, Professional Papers, and Capstones

Bipolar plates are the important components of the PEM fuel cell. The flow distribution inside the bipolar plate should be uniform. Non-uniform flow distribution inside the bipolar leads to poor performance of the fuel cell and wastage of expensive catalyst. A single channel PEM fuel cell is taken and electrochemical analysis is carried out on it. The results are compared with the available published experimental data obtained by other research group, and they are found to be in good agreement. A baseline design of the bipolar plate is taken and numerical analysis is carried out. The results show that the …

Two-Tank Indirect Thermal Storage Designs For Solar Parabolic Trough Power Plants, Joseph E. Kopp

UNLV Theses, Dissertations, Professional Papers, and Capstones

The performance of a solar thermal parabolic trough plant with thermal storage is dependent upon the arrangement of the heat exchangers that ultimately transfer energy from the sun into steam. The steam is utilized in a traditional Rankine cycle power plant. The most commercially accepted thermal storage design is an indirect two-tank molten salt storage system where molten salt interacts with the solar field heat transfer fluid (HTF) through a heat exchanger. The molten salt remains in a closed loop with the HTF and the HTF is the heat source for steam generation. An alternate indirect two tank molten salt …

Optimization Of Solid Oxide Fuel Cell Interconnect Design, Krishna C. Pulagam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Performance of solid oxide fuel cells (SOFC) is dependent of a set of complex physical and chemical processes occurring simultaneously. Interconnect for SOFC is important as it provides electrical connection between anode of one individual cell to the cathode of neighboring one. It also acts as a physical barrier to protect the air electrode material from the reducing environment of the fuel on the fuel electrode side, and it equally prevents the fuel electrode material from contacting with oxidizing atmosphere of the oxidant electrode side. A three-dimensional numerical model has been developed to evaluate the SOFC including the current collector, …

Experimental And Numerical Study Of A Proton Exchange Membrane Electrolyzer For Hydrogen Production, Sachin S. Deshmukh

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen as a fuel source has received attention from researchers globally due to its potential to replace fossil based fuels for energy production. Research is being performed on hydrogen production, storage and utilization methods to make its use economically feasible relative to current energy sources. The PEM electrolyzer is used to produce hydrogen and oxygen using water and electricity. Focus of our study is to provide a benchmark experiment and numerical model of a single cell electrolyzer that can assist in improving the current state of understanding of this system. Parametric analysis of an experimental cell was performed to understand …

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/material interactions pose a critical barrier for higher temperature and longer core life designs. For advanced burner reactors (sodium cooled) such as EBR-II and FFTF, experience has shown that the qualified structural materials and fuel cladding severely limits the economic performance. In other liquid metal cooled reactor concepts, advanced materials and better understanding and control of coolant and materials interactions are necessary for realizing the potentials.

Liquid sodium has been selected as the primary coolant candidate for Gen. IV nuclear energy systems. Global Nuclear Partnership (GNEP) Advanced Burned Reactor (ABR) has …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook, Yitung Chen, Jian Ma

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used extensively in current and proposed nuclear power systems and industrial molten metal transfer operations. Although the Magnetohydrodynamic (MHD) theory that underlies the operation of these types of pumps has been studied extensively in the past few decades, the design of specific EM pumping systems for specific flow cases requires computational tools and expertise, which is lacking in the U.S. However, for the past two years, researchers at UNLV have been utilizing the TC-1 liquid metal loop system at UNLV and an Annular Linear Induction Pump (ALIP) to drive the liquid metal and to develop …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang, Jian Ma

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven systems (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure, and temperature environment, the existing flow measurement techniques (such as Electromagnetic flow meters, Ultrasonic flow meters, Turbine flow meters, etc.) are not accurate and reliable.

The measurement of flow rates (mass flow rates or volume flow rate) plays a notable role in monitoring and controlling the experimental conditions. The bulk flow rates can be obtained through direct methods, which measure the amount of discharged fluids …

Knowledge-Based Information Resource Management System For Materials Of Sodium-Cooled Fast Reactor, Sean Hsieh

Reactor Campaign (TRP)

In the development of advanced fast reactors, materials and coolant/ material interactions pose a critical barrier for higher temperature and longer core life designs. For sodium-cooled fast reactors (SFRs) such as the Experimental Breeder Reactors in Idaho and the Fast Flux Test Facility in Hanford, experience has shown that qualified structural materials and fuel cladding severely limits their economic performance.

Liquid sodium has been selected as the primary coolant candidate for the Advanced Burner Reactor (ABR) of the Global Nuclear Partnership (GNEP). Materials improvement has been identified as a major thrust to improve fast reactor economics. Researchers from universities, national …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2007 Through September 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. The numerical model of a SiC ceramic coupon with two layers of microchannels was developed. Calculations of the factor of safety and probability of failure for the case of a straight channel were performed. Results for a pressure of 7.5 MPa were performed. The thermal and mechanical stress analyses of the Ceramatec HTHX and decomposer were completed.

• Bayonet Heat Exchanger. The thermal and mechanical stress analyses of the bayonet type HTHX and decomposer (Sandia design) were completed. Temperature profiles obtained from thermocouples measured from the Sandia experiments have been applied to the whole packed …

Understanding And Optimizing Surfaces And Interfaces In Energy Conversion Devices, Clemens Heske

UNLV Renewable Energy Symposium

This inaugural event is dedicated to showcasing the renewable/sustainable energy projects of UNLV faculty, staff, students, and collaborators, as well as other external projects underway statewide and nationally. The development and utilization of new technologies to protect the environment, achieve energy independence, and strengthen the economy will be explored. Speakers and poster-session presenters will provide further insight to many ongoing projects and innovative research ideas.

Organized by UNLV’s Office of Strategic Energy Programs, the event offers participants the opportunity to learn about energy projects and will encourage networking and collaboration. This symposium is intended for researchers, educators, students, policy makers, …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2007 Through June 30, 2007, Anthony Hechanova

Publications (NSTD)

• Ceramatec Sulfuric Acid Decomposer. Modeling with different reacting flow channel configurations (ribbed-surface channels, hexagonal channels, and diamond-shaped channels) was performed. The probability of failure for the one channel geometry with different reacting flow channel configurations was calculated to be zero in the three principal directions for all of the cases.

• Bayonet Heat Exchanger. The Matlab code for calculating the probability of failure using a two-dimensional axisymmetric model of the bayonet decomposer was developed. The probability of failure was calculated for the inner and outer SiC walls, and the intermediate quartz wall of the decomposer and found to be …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2007 Through March 31, 2007, Anthony Hechanova

Publications (NSTD)

• The variation of sulfur dioxide production (throughput) of the baseline design of the Ceramatec sulfuric acid decomposer with total mass flow rate of reacting flow has been calculated. According to the calculations, the sulfur dioxide production increases as the total mass flow rate of reacting flow increases regardless of the fact that decomposition percentage of sulfuric trioxide decreases. A parametric study of the baseline design of the Ceramatec sulfuric acid decomposer was performed.

• The thermal performance using various channel geometries for the decomposer was studied. The baseline design (straight channels) has 89.5% thermal efficiency while the thermal efficiency …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2006 Through December 31, 2006, Anthony Hechanova

Publications (NSTD)

Modifications to the single-channel models of the Ceramatec heat exchanger and decomposer concept for hexagonal flow channels under two values of layer-overlapping (50% and 100%) and for diamond-shaped flow channels were completed.

The finite element calculations of the “Ball on Three Ball Test” for ceramic material for the purpose of selecting the appropriate specimen thickness for future experimental testing was performed for plate thicknesses ranging from 2 to 8 mm.

A finite element model of the “Ball on Three Ball Test” was also studied for discs having micro-channels.

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …