Oil, Gas, and Energy Commons^™

The Geology And Production Characteristics Of The Powder River And Other Cbm Basins In Wyoming, Lance Cook

Coalbed Methane Development in the Intermountain West (April 4-5)

7 pages (includes some color illustrations and maps).

A Review Of Cbm Development In The Powder River And Other Wyoming Basins, Don Likwarz

Coalbed Methane Development in the Intermountain West (April 4-5)

6 pages (includes illustrations).

Cbm Water Management: Challenges, Solutions, And Opportunities, Mike Day

Coalbed Methane Development in the Intermountain West (April 4-5)

15 pages (includes color illustrations and maps).

Cbm Development, Ranching, And Agriculture, Nancy Sorenson, Jill Morrison

Coalbed Methane Development in the Intermountain West (April 4-5)

5 pages.

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada, Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded (after pre-straining) engineering materials using a new nondestructive technique based on positron annihilation spectroscopy. The proposed technique is to use γ-rays 2 from a small MeV electron Linac to generate positrons inside the sample via pair production. This method can be used for materials characterization and investigation of defects in thick samples that could not be accomplished by conventional positron techniques or other nondestructive methods. The data generated will …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (December 1, 2001 – February 28, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including HT- 9, EP 823 and 422. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these alloys will be evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. The extent and morphology of cracking of these alloys will further be evaluated …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823: Aaa Task-10 Quarterly (12/1, 2001 –02/28, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The objective of this task is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. The test material will be thermally treated prior to evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The overall results are expected to provide a mechanistic understanding of high-temperature deformation behavior of Alloy EP-823 as a function of heat treatment.

Highlights of Accomplishment

• …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report 11/16/01- 2/15/02, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application.

Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. The transport of oxygen and corrosion products, their interaction and variation of corrosion/precipitation along the flow are not well understood.

The first subtask of this project involves using a …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 11/16/01- 2/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

The AAA program is developing technology for the transmutation of nuclear waste to address many of the long-term disposal issues. An integral part of this program is the proposed chemical separations scheme.

Two activities are proposed in this Phase I task: the development of systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the effect of hydrogen on cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The test materials will undergo appropriate thermal treatments prior to being hydrogen-charged by potentiostatic cathodic polarization technique in a simulated aqueous environment at different temperatures of interest. The specimens, upon completion of testing, will be metallographically examined. Further, the scanning electron microscopy (SEM) will be used to determine the extent and nature of cracking in the specimens tested. The thrust of the proposed …

Project Continuation Proposal: Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project, William Culbreth

Reactor Campaign (TRP)

The AAA program will rely on the use of an accelerator-based transmuter1 to expose spent nuclear fuel to high-energy neutrons. The neutron flux will be sufficient to activate or fission the long-lived isotopes of Tc, I, Pu, Am, Cm, and Np that present a significant radiological hazard in commercial spent fuel. Transmuter fuel will be subcritical and a high-energy proton accelerator is needed to maintain the necessary neutron flux through the use of a neutron spallation target. The maximum neutron energy produced by spallation (~ 800 MeV) is significantly higher than that produced by a commercial light water reactor (~ …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole, Zhiyong Wang, David W. Hatchett

Transmutation Sciences Materials (TRP)

Spallation-neutron-sources, such as those under investigation for use in accelerator-driven transmutation systems, generate neutrons through the collision of high-energy protons, or charged hydrogen atoms, with heavy metal targets such as lead. As a result, these systems also tend to deposit a significant amount of hydrogen in the materials of the transmuter target and superstructure. This can result in accelerated corrosion and changes in the properties of the exposed materials. Of particular importance is a phenomenon called hydrogen embrittlement, in which materials lose their ductility (ability to deform under stress) and become brittle (more susceptible to fracture) after reacting with hydrogen. …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Task V 4th Quarterly Report, Samir Moujaes

Transmutation Sciences Materials (TRP)

The project is moving on target with the newly realigned objective set for the Phase I. Through close communications with Dr. Li and Dr. Jinsuo Zhang from LANL a realignment of the simulation work has been recommended. The reason for that is the vendor of STAR-CD/CHEMKIN had not perfected yet the final coupling of the post processing of output for any potential surface chemistry reaction taking place on the inside pipe surface of the LBE loop. This is because the coupling of CHEMKIN and STAR-CD has been done fairly recently.

Our final effort has been to generate using an innovative …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

Many of the international efforts to develop transmutation technology, including the U.S., Russian, and European scientific communities, have determined that lead bismuth eutectic (LBE) is a potential material for use as a both a spallation target and a coolant. To exploit this potential, a more thorough understanding of the effect and rates of corrosion on steels, particularly non-Russian alloys, inside the LBE systems is required. Properly controlling the oxygen content in LBE systems has been observed to drastically reduce the corrosion of structural steels in LBE. However, the transport of oxygen and formation of corrosion products is not well understood; …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

Alloy EP-823 has been developed as a structural material for Lead Bismuth Eutectic (LBE) systems, such as those under development for nuclear transmutation systems, as well as other applications. However, very little data regarding the mechanical properties of this alloy exists in the open literature, particularly in the temperature regime of interest for transmutation systems. To address this need, the UNLV research team, in collaboration with researchers from Los Alamos National Laboratory, has developed a research program to evaluate tensile properties of Alloy EP-823 stainless steel at elevated temperatures, which is not being performed at any other facility to date. …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, William H. Johnson

Transmutation Sciences Physics (TRP)

To begin developing the database necessary for the validation and benchmarking of the LAHET component of the MCNPX code suite, the UNLV research program has set forth the following objectives. First, the current MCNPX suite will be used to develop models of multi-element neutron detector systems. These models of the detector systems will be incorporated into the design of detailed models for the entire detector-target system. These models will first be used to help design the irradiation experiments, and then will be used to model the behavior of the system. Irradiation experiments corresponding to the detector-target system models will be …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The remediation of nuclear waste created by conventional fission reactors will rely upon the separation of the waste products for further treatment. The UREX+ process now under review will involve the use of an aqueous chemical process to separate out depleted uranium resulting in a product containing minor actinides, fission products, cesium, strontium, technetium, and iodine. The radioactive decay of strontium and cesium produces roughly half of the thermal and gamma production in spent fuel and the relatively short halflife of isotopes of both of these elements requires storage for about 300 years before heat and radiation decreases to safe …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Pang Tao, Denis Beller

Separations Campaign (TRP)

The separation and partitioning of used commercial reactor fuel is a vital component of any reprocessing or transmutation strategy. To process the high actinide fuels required for a transmutation effort, the Chemical Technology Division (CMT) at Argonne National Laboratory (ANL) is developing a pyrochemical separations process. Currently, this work is being done via small experiments. While this is more than sufficient to develop the technologies required to process actinide-bearing fuels, it does not allow for the direct investigation of criticality concerns that would be present in larger systems. As the volume of waste to be treated increases, a higher probability …

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project: Quaterly Report, William Culbreth

Reactor Campaign (TRP)

The national development of technology to transmute nuclear waste depends upon the generation of high energy neutrons produced by proton spallation. Proton accelerators, such as LANSCE at the Los Alamos National Laboratory, are capable of producing 800 MeV protons. By bombarding a lead/bismuth target, each proton may generate 500 or more neutrons that can activate fission products or induce the fission of transuranic isotopes.

The Monte Carlo radiation transport code MCNPX developed at LANL is an important tool in the design of transmuter technology. It must be validated, however, for the neutron energy that will be employed. Experiments are being …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle: Quaterly Report, William Culbreth, Pang Tao

Separations Campaign (TRP)

During the first quarter of the work, the tasks included training students in the use of Monte Carlo codes used in radiation transport studies and the assessment of neutron multiplication factors for specific problems outlined by ANL-East through Drs. Laidler and Vandegrift.

The proposal also included objectives for the first year of work on this project, as listed below. The work conducted in the first quarter of the project was in partial completion of these objectives.

• Train UNLV students in the use of SCALE and/or MCNP for the assessment of nuclear criticality.

• Assess neutron multiplication factor, k_{eff …}

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (September 1 – November 30, 2001) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including HT- 9, EP 823 and 422. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these alloys will be evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. The extent and morphology of cracking of these alloys will further be evaluated …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823: Task 10, First Quarter Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The objective of this task is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. The test material will be thermally treated prior to evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The overall results are expected to provide a mechanistic understanding of high-temperature deformation behavior of Alloy EP-823 as a function of heat treatment.

Highlights of Accomplishment

• …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report August 16,2001- November 15, 2001, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application.

Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. The transport of oxygen and corrosion products, their interaction and variation of corrosion/precipitation along the flow are not well understood.

The first subtask of this project involves using a …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 8/16/01- 11/15/01, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

The AAA program is developing technology for the transmutation of nuclear waste to address many of the long-term disposal issues. An integral part of this program is the proposed chemical separations scheme.

Two activities are proposed in this Phase I task: the development of a systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part …

Assessment Of Criticality Safety For Cylindrical Containers To Be Used In The Processing Of Spent Fuel, William Culbreth, Daniel R. Lowe, Jason Viggato

Separations Campaign (TRP)

The UREX process separates uranium from transuranic wastes (TRU) and fission products (FP). Nuclear reactors require fissile isotopes that will absorb neutrons and break apart into smaller nuclei while releasing a large amount of energy as well as multiple neutrons. Fissile isotopes in spent fuel include not only ²³⁵U, but also ²³⁹Pu, ²⁴¹Pu, and several isotopes of americium (Am) and curium (Cm).

TRU contains the actinides with atomic numbers greater than that of uranium. This includes Pu, Np, Am, and Cm. When TRU is separated from uranium, the TRU still poses a significant risk of sustaining a …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report, Second Quarter (June To August 2001), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA UPP consists of three components: Program Administration, Research Infrastructure Augmentation, and Student Research.

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (June 1 – August 31, 2001) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The subject task entitled “Hydrogen-Induced Embrittlement of Candidate Target Materials for Applications in Spallation-Neutron-Target Systems” had commenced during the quarter ending on August 31, 2001. A research account has been established, contracts for both faculty and students have been prepared, and efforts are well underway to embark on the related research activities, as proposed.

As the title of this project implies, the primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallationneutron- target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Pang Tao

Separations Campaign (TRP)

To mitigate the waste created by conventional fission reactors, spent nuclear fuel must be mechanically separated from its cladding. For the development of fuel processing technology to support the Advanced Accelerator Applications (AAA) Program, aqueous and pyrochemical processes will be used to further separate technetium and iodine, uranium and the higher actinides (see Figure 1 for an example of the process layout)1. The higher actinides, including plutonium, americium, curium, and neptunium will be separated from the waste to facilitate their fabrication into new fuel for placement in a transmuter. High-energy neutrons generated by spallation in the transmuter break down these …

Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project, William Culbreth

Reactor Campaign (TRP)

The AAA program will rely on the use of an accelerator-based transmuter to expose spent nuclear fuel to high-energy neutrons. The neutron flux will be sufficient to activate or fission the long-lived isotopes of Tc, I, Pu, Am, Cm, and Np that present a significant safety hazard in commercial spent fuel. Transmuter fuel will be subcritical and a high-energy proton accelerator is needed to maintain the necessary neutron flux through the use of a neutron spallation target. The maximum neutron energy produced by spallation (~ 600 MeV) is significantly higher than that produced by a commercial light water reactor (~ …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Darrell Pepper, Randy Clarksean

Separations Campaign (TRP)

Two activities are proposed: the development of a Systems Engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model will be the start of an integrated approach to the analysis of the materials separations associated with the national AAA program. A second portion of the project will streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral to the systems engineering …