Oil, Gas, and Energy Commons^™

Cuando Viene El Agua: Percepciones De Los Impactos Sociales Del Proyecto Hidroeléctrico “Chan-75” En Las Comunidades Ubicadas En La Cuenca Del Río Changuinola, Bocas Del Toro, Jeffery D. Stein

Independent Study Project (ISP) Collection

This report analyzes the anticipated social impacts of a hydroelectric project, titled “Chan-75,” in the surrounding communities. The project is located in the Bosque Protector de Palo Seco (BPPS) protected area along the Changuinola River. The flooding of 750 ha to create a reservoir for the dam will require the resettlement of roughly 1,000 residents of at least four indigenous Ngöbe Buglé communities including Valle del Rey, Charco la Pava, Changuinola Arriba, and Guayabal, in addition to the submersion of thousands of ha of farmland belonging to residents of nearby communities (Cordero et al). Once completed, the dam will generate …

Potentiality Of Biogas And The Role Of Substrates In Biogas Formation Potential, Scott Shealy

Independent Study Project (ISP) Collection

Biogas infrastructure development, particularly in countries such as Vietnam, has the potential to provide great benefits to people living agrarian lifestyles in rural areas. Decentralized wastewater treatment facilities that utilize anaerobic technologies to digest organic waste for the purpose of collecting methane provide a number of benefits to centralized use as well. In both cases, users benefit from the production of methane gas, wastewater treatment, nutrient recycling, and organic fertilizers. In the case of decentralized use, as is most prevalent in Vietnam, integrated farming methods, such as the VACB model, allow farmers to reap the benefits of a wide array …

Nevada Risk Assessment/Management Program (Nramp) – Phase 2: Quarterly Progress Report, Oct. 1, 2006- Dec. 31, 2006, Klaus J. Stetzenbach

Nevada Risk Assessment/Management Program

Work conducted in this initial period consisted of work start-up (technical, administrative, contractual), and interviewing/site visits with DOE NVO staff (and support contractors) and HRC staff to quickly ascertain current technical activities and priorities as related to the scope of this task.

Since much of the technical work scope builds on previous technical work, it was considered critical to determine the changes (programmatic, technical, and regulatory) that have occurred over the past several years that directly relate to the scope. It was also equally important to determine the technical and programmatic priorities that have been established in the interim.

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2006 Through December 31, 2006, Anthony Hechanova

Publications (NSTD)

Modifications to the single-channel models of the Ceramatec heat exchanger and decomposer concept for hexagonal flow channels under two values of layer-overlapping (50% and 100%) and for diamond-shaped flow channels were completed.

The finite element calculations of the “Ball on Three Ball Test” for ceramic material for the purpose of selecting the appropriate specimen thickness for future experimental testing was performed for plate thicknesses ranging from 2 to 8 mm.

A finite element model of the “Ball on Three Ball Test” was also studied for discs having micro-channels.

Decoupling And Disturbance Rejection Control For Target Circulation, Jian Ma, Joon S. Lee, Woosoon Yim

Reactor Campaign (TRP)

In 1998, the Institute of Physics and Power Engineering (IPPE) and Experimental and Development Organization “Gidropress” in Russia, began the design and construction of a prototype lead-bismuth eutectic (LBE) accelerator target, the Target Complex 1 (TC-1), under the International Science and Technology Center (ISTC) project #559 (“Pilot Flow Lead-Bismuth Target of 1 MW Power for Accelerator Driven Systems”) in support of the international efforts to develop accelerator-driven spallation systems for nuclear transmutation and other applications.

During the thermal and engineering test of the TC-1 in 2005 at UNLV, it was observed that the existing control algorithm led to a very …

Modeling And Design Algorithms For Electromagnetic Pumps, Daniel P. Cook

Reactor Campaign (TRP)

Electromagnetic (EM) induction pumps are used in a number of nuclear energy related applications, such as circulation of molten lead-bismuth eutectic alloys in neutron targets, and circulation of liquid sodium metal in Gen IV Sodium-cooled Fast Reactors (SFR). Because EM pumps have no moving parts which can fail, they are considerably more reliable than conventional mechanical pumps for molten metal usage, and thus EM pumps are favored over mechanical pumps even though their pumping efficiency is lower and their initial cost is higher when compared to mechanical pumps of similar flow rates.

The research objectives of this task are:

• A …

Thermal Transient Flow Rate Sensor For High Temperature Liquid Metal Cooled Nuclear Reactor, Yingtao Jiang

Reactor Campaign (TRP)

In nuclear power plants and accelerator driven system (ADS) for nuclear waste treatment, it is important to monitor the coolant flow rate in the reactor core and pipe-line. In such a strong irradiation, high pressure and temperature environment, no accurate local flow measurement technique is readily available. Electromagnetic (EM) flow meter is popular in low temperature application as it is a non-intrusive technology. However, additional voltage will be produced due to temperature, flow, pressure, the chemical properties of the liquid metal and surface condition of the steel walls. In addition, the non-definite wetting behavior of liquid lead-bismuth to the electrically …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

During the past academic year, this project was focused on the characterization of residual stress in welded specimens consisting of austenitic and martensitic stainless steels using an activation technique based on the Positron Annihilation Spectroscopic (PAS) method. The extent of residual stress was expressed in terms of three line-shape parameters (S-, W- and T-). Further, efforts were made to characterize linear lattice defects such as dislocations in the vicinity of Fusion-Line (FL), Heat-Affected- Zone (HAZ), and the base material of the welded specimens using Transmission Electron Microscopy (TEM). The metallurgical microstructures at these three regions have also been evaluated by …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes and facilities (e.g., transmutation of nuclear waste, fast reactors, and spallation neutron sources) impose special demands on materials, which must withstand high temperatures, high radiation fields, and chemical corrosion. Proposed schemes for transmuting nuclear waste require a nonmoderating coolant such as lead-bismuth eutectic (LBE). While LBE corrodes most steels, small amounts of oxygen in the LBE greatly reduces the corrosion rate, and could ideally re-grow a damaged oxide layer in-situ. The protective oxide layer would thus be self-healing. However, the fundamental understanding of the role of oxygen and passivating oxide layers is presently incomplete.

During the present …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is focused on the evaluation of the effects of silicon content on both the corrosion behavior and radiation-induced embrittlement of martensitic stainless steels having compositions similar to that of modified 9Cr-1Mo steel, also known as T91 grade steel. T91 grade steel was selected to be a candidate structural material to contain molten lead-bismuth eutectic (LBE), which can act both as a target material and a coolant during the spallation process. The operating temperature during this process may range from 420-550 °C. Thus, moderate tensile strength of the containment material (T91) is a major requirement.

The beneficial effects of …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and apply …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead-bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive to …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The major objectives will lead to a creation of framework that combines all the strengths of AMUSE’s complicated calculations, well-established commercial system process package and ISOPro’s flexible parameter optimization modules. Development of the process simulation code can be done using the solvent extraction process at Argonne National Laboratory in collaboration with the research team from Mechanical Engineering Department at UNLV.

Research accomplishments:

• Integrated the ASPEN-Plus process model with the ISOPro system engineering modeling package, developed by the UNLV team.
• Tested the simplified system process integration using the ISOPro package.
• Generated complete version of the ISOPro package user manual and tutorial. …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Impact Of The Synthesis Process On Structure Properties For Afci Fuel Candidates, Kenneth Czerwinski

Fuels Campaign (TRP)

Synthesis of actinium mononitrides using carbothermic reduction of the corresponding oxides has a few outstanding issues, including the formation of secondary phases such as oxides and carbides and low densities of the final product. Furthermore the requirement of a high process temperature at 1700°C, for more than 12 hours is also a drawback particularly for Americium-bearing samples. Therefore, it is important to explore the use of other possible routes to synthesize actinide mononitrides.

A low temperature process is used in this research to produce actinide mononitrides using a fluoride route in which the first step is to mix the actinide …

Solution-Based Synthesis Of Nitride Fuels, Tyler A. Sullens, Kenneth Czerwinski

Fuels Campaign (TRP)

The preliminary studies into the synthesis of actinide nitride fuels through a low temperature, liquid ammonia based synthesis route have been conducted on the uranium containing system, and there is good indication for the success of synthesizing uranium (III) nitride. The dissolution of iodine in ammonia is a rapid process, resulting in a pale green solution, which does not result in any observable oxidation of iodine. The cannula transfer of dissolved iodine into the reaction vessel containing U metal has been conducted with little to no residual iodine remaining in the original flask. The metal being used for these reactions …

Economic Analysis Of Cellulase Production Methods For Bio-Ethanol, Jun Zhuang, Mary A. Marchant, Sue E. Nokes, Herbert J. Strobel

Biosystems and Agricultural Engineering Faculty Publications

The cost of cellulase enzymes has limited the feasibility of producing ethanol from fibrous biomass. Traditional submerged fermentation (SmF) was compared to an alternative method of producing cellulase, solid state cultivation (SSC). Results from an economic analysis indicated that the unit costs for cellulase enzyme production were $15.67 (The prices are all 2004 prices in this article, except otherwise stated. We deflated newer prices to 2004 prices using a deflation factor 0.9 per year and inflated older prices to 2004 prices using an inflation factor 1.1.) per kilogram ($/kg) and $40.36/kg, for the SSC and SmF methods, respectively, while the …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic methods, intermediate chemical phases at the interface, intermixing/ diffusion behavior, and the electronic interface structure as a function of material (metal and coating materials) and temperature are examined.

In the past year, emphasis was placed on a detailed analysis and description of the Cs/SiC interface formation process.

The Potential For Ch4-Enriched Biogas As A Transport Fuel In Ireland, Niamh Power

Theses

Ireland needs a biofuel industry- to aid compliance with the Kyoto Protocol, the Biofuels Directive and to secure its energ>' supply. The overall aim of this work is to assess the potential of CH4-enriched biogas as a transport fuel in Ireland. Biogas is produced during the anaerobic digestion of biomass. This work investigates biogas production from two different feedstocks; biodegradable municipal waste and agricultural crops. To assess the potential for biogas as a transport fuel the alternatives to biogas are investigated and compared. Thus digestion and composting of biodegradable municipal waste, and biogas and ethanol production from agricultural crops …

Multi-Phase Flow Analysis In Oil And Gas Engineering Systems And Its Modelling, Orlando F. Ayala, Luis F. Ayala, Orlando M. Ayala

Engineering Technology Faculty Publications

[Introduction] Two-phase flow is very common in industrial processes and its applications were already in use in ages as remote as the era of Archimedes. At the present time, many industrial processes rely on multi-phase phenomena for the transport of energy and mass or for material processing. During the last century, the nuclear, chemical and petroleum industries propelled intense research activity in the area. Their efforts have been aimed at the demystification of the mechanisms taking place during this complex flow situation.

Anaerobic Digestion: Decision Support Software, Marco Poliafico

Theses

Ireland has significant quantities of livestock; meat exportation is a vibrant sector of the economy. Environmental management of animal wastes has therefore become an important concern. On the other hand in the last decade, national and EU policy debate has highlighted the need to investigate alternative energy: in particular energy for transport.

This study investigates the quantities of animal wastes produced in Ireland and their potential treatment using Anaerobic Digestion technologies. In 2005 Ireland had over 8 millions animals (cattle and pigs) and the annual slaughter accounted for over 4.2 million of these creatures. These animals have been responsible for …

Windmill Documentary, Timothy David Stoltenburg

Honors Capstones

Capstone submitted as a graduation requirement for the BSU Honors Program.

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2006 Through September 30, 2006, Anthony Hechanova

Publications (NSTD)

Hydrodynamics and thermal numerical modeling coupled with sulfur trioxide decomposition for the one channel geometry with three different channel configurations were performed. The results obtained from the numerical modeling were compared with the baseline design under the same boundary and operation conditions. The case with diamond shaped channels has the highest percentage of sulfuric acid decomposition. The baseline channel geometry has the lowest pressure drop compared with other cases.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.

Dissolution, Reactor, And Environmental Behavior Of Zro 2 -Mgo Inert Fuel Matrix Neutronic Evaluation Of Mgo-Zro2 Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

In the second year of the “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project initiated and directed by UNLV, the Ben-Gurion University (BGU) group research was focused on the development of practical PWR core nuclear design fully loaded with Reactor Grade (RG) Pu fuel incorporated in fertile free matrix. The design strategy was based on the basic feasibility study results performed at BGU in the Year 1 of the project.

College Of Engineering Senior Design Competition Spring 2006, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2006 Through March 31, 2006, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The UNLVRF HTHX Project quarterly meeting was held in Albuquerque, NM, March 16 and 17, 2006. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. A tour of Sandia National Laboratory was also provided that included a visit to their sulfuric acid decomposition test apparatus. There were 24 attendees from universities, national laboratories, and private industry. Collaborators discussed their research progress. The next meeting will be in July in Salt Lake City, UT.

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #6, Kamalakar Alluri, Georg F. Mauer

Fuels Campaign (TRP)

Project Milestones

• Completed a systematic study seeking to arrive at an optimized plant configuration, using value engineering techniques in January 2006.

• Vision-based robot serving and automated plant safety monitoring is currently in progress.

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (November 2005 – January 2006), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …