Oil, Gas, and Energy Commons^™

Application Of Improved Hierarchic Analytic Process In The Classification Of Mine Hydrogeological Types, Wang Tiantian, Jin Dewu, Yang Jian, Liang Xiangyang

Coal Geology & Exploration

The classification of mine hydrogeological type is an important part of mine hydrogeology work. It is of great significance to analyze water filling conditions, evaluate water hazard and guide mine water prevention work. In order to evaluate mine hydrogeological conditions, this paper introduced optimal transfer matrix to improve hierarchic analytic process, and then applied this method to classify mine hydrogeological types. Taking four pairs of active mines in Hujierte mining area of Inner Mongolia as an example, the evaluation index system for classification of mine hydrogeological types was built on the basis of analysis of the hydrogeological conditions, then theoretical …

Design And Application Of Drilling Rod Vibration Frequency Measurement System, Liu Naipeng, Hu Yule, Wang Wei

Coal Geology & Exploration

During drilling, resonance is generated when the natural frequency of the drilling rod is consistent with the external excitation frequency. This will cause fatigue-failure of the drilling rod and serious consequences. To avoid this, a drilling rod vibration measurement system based on Micro-Electro-Mechanical System was designed. This system uses the three-axis acceleration sensor to measure the acceleration of the drilling rod in three directions. The upper computer software written in LabVIEW can storage, upload, display and process data. Then the fast Fourier Transform was taken to analyze the vibration frequency of the drilling rod. Finally the system is installed on …

Elastic Mechanics Solution Of Water Proof Key Layer In Coal Seam Floor Under High Water Pressure, Wang Yan, Yao Duoxi, Lu Haifeng

Coal Geology & Exploration

Aiming at the problem of water resisting capacity of the key layer in seam floor under the action of high pressure water, the key stratum was simplified as a fixed beam. The stress and displacement were calculated by the stress function method and the semi inverse method respectively. The results of two calculations were compared with the FLAC^3D results. The results show that the stress and displacement obtained by the stress function method are more appropriate than those calculated by the FLAC^3D method. It is suggested that for elastic mechanics analytic method of the fixed beam of the …

Integrated Identification Of Sequence Boundary Through Outcrop, Seismic With Logging And Geochemistry: A Case Of Jurassic In Northeastern Margin Of Ordos Basin, Zhang Tianfu, Zhang Yun, Cheng Yinhang, Miao Peisen, Ao Cong, Jin Ruoshi, Duan Lianfeng, Duan Xiaolong

Coal Geology & Exploration

Jurassic strata is mainly rock series containing coal and uranium in Ordos basin. The recognition of Jurassic sequence interfaces were mainly relied on the field outcrop, logging lithology of unconformity surface or the sedimentary discontinuity. However, it is tend to experience human recognition of randomness in the sequence interfaces recognition without macroscopic characteristics. Therefore, based on routine identification work such as outcrop profile and electrical curve of nearly 1 000 boreholes, combined with vertical changes of two-dimensional seismic profile and chemical index of alteration(CIA), three long-term cycle sequence interfaces(TSB1-TSB3) and seven medium-term cycle sequence interfaces(SB1-SB7) were finally identified in Jurassic …

Response Relation Between Fracturing Curve And Reservoir Pollution Degree Of Coalbed Methane Wells, Zhuang Dengdeng, Wang Yanbin, Tao Chuanqi, Chen Yan

Coal Geology & Exploration

In order to study the relationship between response curve and the pollution degree of fractured reservoir, taking Shizhuang block in Qinshui basin as an example, wells with different sensitivity of reservoir in the block were selected, through comparison of the difference of the dropping trace characteristics after the hydraulic curve reaches the fracture pressure in the fracturing curves of fracturing operation in different wells, the response law of hydraulic dropping trace and the reservoir sensitivity was summed up. Then in the same block according to the dropping trace of the hydraulic curves, the sensibility of reservoir was judged in several …

Absorber And Window Study – Cdsexte1-X/Cdte Thin Film Solar Cells, Chih-An Hsu

USF Tampa Graduate Theses and Dissertations

CdTe an II-VI semiconductor has been a leading thin film photovoltaic material due to its near ideal bandgap and high absorption coefficient [1]. The typical thin film CdTe solar cells have been of the superstrate configuration with CdS (Eg-2.42eV) as the n-type heterojunction partner. Due to the relatively narrow bandgap of CdS, a wider bandgap n-type window layer has recently emerged as a promising substitute: alloys of MgyZn1-yO have been successfully used as the emitter or window layer. The benefits in the usage of MgyZn1-yO (MZO) are its tunable bandgap and wide optical spectrum on optoelectronic devices. Due to an …

Fundamental Insights On The Electrolysis Of Co2 Using Solid Oxide Electrolysis Cells, Juliana Silva Alves Carneiro

Wayne State University Dissertations

The work reported in this thesis focused on providing a fundamental understanding, at the molecular level, required to guide the effective design of electrocatalysts towards a superior reaction kinetics on the electrode of solid oxide electrolysis cells SOECs devices (SOECs) during the CO2 electrolysis. High temperature SOECs are electrochemical energy conversion technologies, that have emerged as promising alternatives to mitigate environmental issues associated with combustion-based technologies, such as the rising atmospheric CO2 levels. The conversion of excess CO2 into high-energy molecules, such as CO can be efficiently achieved through the use of SOEC – which facilitates the electrochemical reduction of …

Retention Strategies For Oil And Gas Industry Managers, Faye Gerard

Walden Dissertations and Doctoral Studies

The turnover cost of specialized employees in the oil and gas industry can exceed 400% of an employee's annual salary. The purpose of this multiple case study was to explore successful strategies that oil and gas company managers used to retain specialized employees. The specific population for the study was 8 managers from 4 oil and gas companies in a metropolitan city in the southern United States, which included 5 hiring managers and 3 engineering managers who had demonstrated success in retaining specialized employees. The conceptual lens used in this research study was the job embeddedness theory. Study data were …

Transmission Electron Microscopy Analysis Of Silicon-Doped Beta-Gallium Oxide Films Grown By Pulsed Laser Deposition, Cynthia Thomason Bowers

Browse all Theses and Dissertations

Due to the large band gap of β-Ga2O3 and recent improvements toward high quality native substrates and the ability to shallow dope epitaxial β-Ga2O3 it is an attractive material for applications in power electronic devices. Such devices require advances in the areas of thin film growth and carrier concentration control to deliver high mobility films appropriate for the device structures. Transmission electron microscopy (TEM) analysis can provide information concerning doping, crystal structure, and internal strain which will be valuable to assess the role of defects and impurities on the transport properties for feedback to optimize the bulk and epitaxial growth …

Energy Efficiency And Fatigue Failure On Gears And Bearings For Processing Rebar Steel, Jesus Gabriel Garcia

Open Access Theses & Dissertations

Steel industry is a major emitter of air pollutants, a leading industrial consumer of water, a minor source of contaminated liquids, a massive producer of solid waste, and a significant source of CO2. The objective on this thesis work is to minimize the greenhouse gas emissions when processing steel. Gears and bearings were evaluated based on their performance when exposed to cyclic stresses. The importance for having a proper set up on rolling mills to increase efficiency for processing rebar steel has been detailed on paper. In contrast, mechanical vibration has been measured on gears and bearings to determine efficiency …

Strategies To Improve The Electrochemical Of Performance Transition Metal Compounds As Anode Materials For Li-Ion Batteries, Noemi Dominguez

Open Access Theses & Dissertations

Nowadays, our society depends on fossil fuels as the main energy source. However, depletion, price fluctuations, and other concerns, such as global warming, have led to an exhaustive research for renewable energy resources. Here is where electrochemical energy systems play a critical role since they can provide power when renewable energy is not available. Among these electrochemical energy storage systems Li-ion batteries (LIBs) have shown higher volumetric, gravimetric, and power density capacities over other battery systems.

However, commercial LIBs are still relying on graphite base materials for the anode. However, graphite possesses a low specific capacity. Recently, transition metal compounds …

Design And Preliminary Evaluation Of A Supercritical Carbon Dioxide Brayton Cycle For Solar Dish Concentrator Clean Energy Production, Danielle Nobles-Lookingbill

UNLV Theses, Dissertations, Professional Papers, and Capstones

As we move toward energy independence and more ambitious clean energy goals, solar energy research must push the efficiency limits of traditional energy generation systems. Increases in efficiency can be achieved by increasing the hot temperature of the power cycle. Recent research demonstrates the potential for increased efficiency and a vastly smaller component size when supercritical carbon dioxide Brayton power cycles are used. Concentrated solar and nuclear heat sources are capable of achieving the high working fluid temperatures needed for significant efficiency gains. This NSF EPSCoR funded, experimental research system is designed to exploit the uniquely immense solar irradiance of …

Fractionation And Characterization Of Lignin Streams From Unique High-Lignin Content Endocarp Feedstocks, Wenqi Li, Kirtley Amos, Mi Li, Yunqiao Pu, Seth Debolt, Arthur J. Ragauskas, Jian Shi

Biosystems and Agricultural Engineering Faculty Publications

Background: Lignin is a promising source of building blocks for upgrading to valuable aromatic chemicals and materials. Endocarp biomass represents a non-edible crop residue in an existing agricultural setting which cannot be used as animal feed nor soil amendment. With significantly higher lignin content and bulk energy density, endo-carps have significant advantages to be converted into both biofuel and bioproducts as compared to other biomass resources. Deep eutectic solvent (DES) is highly effective in fractionating lignin from a variety of biomass feedstocks with high yield and purity while at lower cost comparing to certain ionic liquids.

Results: In the present …

A Cost Benefit Analysis Of Using A Battery Energy Storage System (Bess) Represented By A Unit Commitment Model, Nemanja Mihailovic

USF Tampa Graduate Theses and Dissertations

This thesis aims to provide a general overview of a cost and benefit analysis of incorporating a battery energy storage system within unit commitment model.

The deregulation of the electricity market in the U.S. has only been around for the last two decades. With renewable energy and energy storage systems becoming less expensive, a decentralized market scheme is becoming more popular and plausible. The scope of this work is to provide a fundamental understanding of unit commitment and a cost analysis of applying a battery energy storage system to an already established power system.

A battery energy storage system (BESS) …

Characterization And Evaluation Of Cordless Nailer Performance For Liquid And Gaseous Fuels, Mark Carioscio

Master's Theses (2009 -)

The Paslode Cordless XP Framing Nailer is a combustion-powered nail gun that operates using a fuel blend of a propylene and 1-butene. This tool is designed to drive nails using a piston driven by a combustion reaction. The current fuel blend is able to fire approximately 1200 shots per fuel cartridge and match the energy output of pneumatic, corded nailers on the market. This thesis is written with the intent to gain a better understanding of the operation of the tool and how its performance varies when the fuel source is altered. A bizonal combustion model was created to simulate …

The Effect Of Processing Conditions On The Energetic Diagram Of Cdte Thin Films Studied By Photoluminescence, Shamara P. Collins

USF Tampa Graduate Theses and Dissertations

The photovoltaic properties of CdTe-based thin films depend on recombination levels formed in the CdTe layer and at the heterojunction. The localized states are resultant of structural defects (metal sublattice, chalcogen sublattice, interstitial), controlled doping, deposition process, and/or post-deposition annealing. The photoluminescence study of CdTe thin films, from both the bulk and heterojunction, can reveal radiative states due to different defects or impurities. Identification of defects allows for potential explanation of their roles and influence on solar cell performance. A thorough understanding of the material properties responsible for solar cell performance is critical in further advancing the efficiency of devices. …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Radical Social Ecology As Deep Pragmatism: A Call To The Abolition Of Systemic Dissonance And The Minimization Of Entropic Chaos, Arielle Brender

Student Theses 2015-Present

This paper aims to shed light on the dissonance caused by the superimposition of Dominant Human Systems on Natural Systems. I highlight the synthetic nature of Dominant Human Systems as egoic and linguistic phenomenon manufactured by a mere portion of the human population, which renders them inherently oppressive unto peoples and landscapes whose wisdom were barred from the design process. In pursuing a radical pragmatic approach to mending the simultaneous oppression and destruction of the human being and the earth, I highlight the necessity of minimizing entropic chaos caused by excess energy expenditure, an essential feature of systems that aim …

Lithium And The Foreseeable Future, Paolo Vargas

Mechanical Engineering Undergraduate Honors Theses

This paper aims to clarify the uncertainties regarding worldwide lithium resource availability in the years to come. Previous studies made on the subject are presented with some ambiguity and this work intends to fill the gaps. The information and data presented throughout this script with respect to global lithium resources and reserves are mostly based on data released by the United States Geological Survey (USGS). Lithium resource availability in the future is a point of paramount significance primarily for the automotive, portable electronics, and the power generation industry. Since, a change of supply would ultimately affect the price of lithium, …

Non-Covalent Functionalization Of Graphene Films For Uniform Nanoparticle Deposition Via Atoic Layer Deposition, Ty Seiwert

Mechanical Engineering Undergraduate Honors Theses

Graphene functionalized with platinum (Pt) and palladium (Pd) has proven to be highly effective as a hydrogen sensor. Deposition methods such as Atomic layer deposition (ALD) can be further enhanced by pretreating the graphene with a non-covalent surfactant prior to nanoparticle deposition. In this study, graphene-based sensing devices will be fabricated by ALD deposition. The graphene will be non-covalently functionalized using sodium dodecyl sulfate (SDS) anionic surfactant prior to ALD deposition. The aim of this study is to test the deposition pattern achieved by varying the amount of time that graphene is treated with the SDS surfactant. Initially, ALD deposition …

Characterization Of Bacteriorhodopsin And Halorhodopsin Reconstituted In Lipid Bilayer Membranes, Joel Domkam Kamwa

Graduate Theses and Dissertations

Motivated to produce electricity with photon activated ion pumps, the main purpose of this work was to characterize the photosynthetic membrane proteins bacteriorhodopsin (proton pump) and halorhodopsin (chloride pump). The proteins were re-suspended in lipid bilayers. For this work, an experimental set-up was built which included: chambers for lipid bilayer formation and characterization, lasers for ion pump activation, and an AxoPatch electrophysiology system for small photocurrent measurement. Lipid bilayer membranes were formed using mostly folding method: folding two monolayers together. The membranes were characterized by their resistance, capacitance, and generated photocurrent. Photocurrent was generated upon illumination of lipid-protein membranes with …

Algal Biofuel: The Future Of Green Jet Fuel In Air Transportation, Rajee Olaganathan

Publications

The aviation industry is one of the major contributors for the greenhouse gases. As air travel has become inevitable in this modern era, and fossil fuel usage is not sustainable, it is essential to produce renewable fuel and commercialize it to reduce the greenhouse gas emissions. In order to produce an alternate aviation biofuel a lot of industrial and academic collaborations have been developed worldwide. The main concern of this collaborative research is to produce aviation biofuel from renewable resources with low environmental impacts, and which is sustainable at an economically viable price. This mini-review briefly discusses the biotechnological approaches …

Assessing Land Deformation And Sea Encroachment In The Nile Delta, Egypt, Esayas Gebremichael

Research and Creative Activities Poster Day

Persistent scatterer interferometric analyses were conducted on a stack of 84 Envisat ASAR scenes spanning 7 years (2004 to 2010) over the entire Nile Delta of Egypt and surroundings to monitor the ongoing spatial and temporal land deformation, identify the factors controlling the deformation, and model the interplay between sea level rise and land subsidence to identify areas and populations threatened by sea encroachment by the end of the 21st century. Findings include: (1) general patterns of subsidence in the northern delta, near-steady (none) subsidence in the southern delta, separated by a previously mapped flexure zone undergoing uplift; (2) high …

In Situ Extrinsic Doping Of Cdte Thin Films For Photovoltaic Applications, Imran Suhrid Khan

USF Tampa Graduate Theses and Dissertations

The Cadmium Telluride thin film solar cell is one of the leading photovoltaic technologies. Efficiency improvements in the past decade made it a very attractive and practical source of renewable energy. Considering the theoretical limit, there is still room for improvement, especially the cell’s open circuit voltage (VOC). To improve VOC, the p-type carrier concentration and minority carrier lifetime of the CdTe absorber needs to be improved. Both these parameters are directly related to the point defect distribution of the semiconductor, which is a function of deposition stoichiometry, dopant incorporation and post-deposition treatments.

CdTe films were deposited by the Elemental …

Functionalized Nanoporous Carbon Scaffolds For Hydrogen Storage Applications, Christopher L. Carr

Doctoral Dissertations

"Recent efforts have demonstrated confinement in porous scaffolds at the nanoscale can alter the hydrogen sorption properties of metal hydrides, though not to an extent feasible for use in onboard hydrogen storage applications, proposing the need for a method allowing further modifications. The work presented here explores how the functionalization of nanoporous carbon scaffold surfaces with heteroatoms can modify the hydrogen sorption properties of confined metal hydrides in relation to non-functionalized scaffolds (FS). Investigations of nanoconfined LiBH₄ and NaAlH₄ indicate functionalizing the carbon scaffold surface with nitrogen can shift the activation energy of hydrogen desorption in excess of …

Processing Different Mixtures Of Regionally Available Resources To Create Pellets That Meet A Minimum Standard, Jacob Hixson

Masters Theses

There are several ways to produce energy today, one of the oldest is the gasification of biomass. This process uses a fire to heat the material until it starts to produce gasses that are used as fuel. There are several types of biomass that can be used, many of which have large pieces with low bulk densities. By pelletizing the biomass bulk density increases and allows the opportunity to add in other biomass materials.

There are standards for condensing large pieces of biomass to smaller pelletized materials. Pellet Fuels Institute has set minimum standards for pellets used in the different …

Automated Cfd Optimization To Maximize Wind Farms Performance And Land Use, Rafael Valotta Rodrigues

Electronic Theses and Dissertations

In this research, a computational system was designed to analyze and optimize the layout of wind farms under variable operational conditions. At first, a wind turbine computational fluid dynamic (CFD) model was developed covering the near wake. The near wake flow field was validated against near wake velocity data from the MEXICO experiment. The CFD simulation demonstrated that the tip speed ratio and the pitch angle greatly influence the near wake behavior, affecting the velocity deficit and the turbulence intensity profile in this region. The CFD model was extended to cover the far wake, aiming to become a computational tool …

Application Of Machine Learning On Fracture Interference, Dennis Wayne Chamberlain Jr.

Graduate Theses, Dissertations, and Problem Reports (ETD)

A method has been developed that locates and determines well-to-well hydraulic fracture interference (frac-hit) in shale plays using hard data. This method uses Artificial Neural Networks (ANN) with designated parameters and target outputs in conjunction with graphs of gas flowrate, tubing pressure, and cumulative gas prediction. The method was created to address the significant increase in frac-hit occurrences due to the infill wells being completed in shale plays. The production data of the well is first cleaned to eliminate outliers in the initial timeframe of the well and periods of no production so that the ANN model can be accurately …

Integrated Study On The Applicability Of Co₂-Eor In Unconventional Liquids Rich Reservoirs, Dheiaa Khafief Khashan Alfarge

Doctoral Dissertations

"Unconventional Liquids Rich Reservoirs (ULR) such as Bakken, Niobrara, and Eagle Ford have become the main target for oil and gas investors as conventional formations started to deplete and diminish in number. These unconventional plays have a huge oil reserve; however, the predicted primary oil recovery is still low as an average of 7.5 %. Unconventional Improved Oil Recovery (UIOR) techniques are still a new concept in the oil industry because there is no commercial project for any IOR technique so far. Injecting carbon dioxide (CO₂) might be the most potential strategy to improve oil recovery in such complex plays. …

Wetting Properties Of Structured Interfaces Composed Of Surface-Attached Spherical Nanoparticles, Bishal Bhattarai

Browse all Theses and Dissertations

In this thesis, the effects of the external pressure and surface energy on stability and wetting transition at nanotextured interfaces are studied using molecular dynamics and continuum simulations. The surface roughness of the composite interface is modeled via an array of spherical nanoparticles with controlled wettability. It was found that in the absence of external pressure, the liquid interface is flat and its location relative to the solid substrate is determined by the radius of the particle and the local contact angle. With increasing pressure on the liquid film, its interface becomes more curved and the three-phase contact line is …