Hydrology Commons^™

Upper Spokane River Model In Idaho: Boundary Conditions And Model Setup For 2001, Scott A. Wells, Robert Leslie Annear, Chris Berger

Civil and Environmental Engineering Faculty Publications and Presentations

The Spokane River in Idaho originates in Coeur d’Alene Lake (Figure 1 and Figure 2). The section of the Spokane River from Coeur d’Alene Lake to the Washington state line is the subject of a water quality study for the US Environmental Protection Agency. The objective of this study is to create a water quality and hydrodynamic model of the Spokane River in Idaho using CE-QUAL-W2 Version 3.1 (Cole and Wells, 2002).

Since the Spokane River is water quality limited, a hydrodynamic and water quality model for the Spokane River in Washington was developed by Portland State University for the …

Upper Spokane River Model: Model Calibration, 2001, Chris Berger, Robert Leslie Annear, Benjamin Welle

Civil and Environmental Engineering Faculty Publications and Presentations

The Upper Spokane River system under consideration is located in the Northeastern part of Washington State and runs from the Stateline with Idaho, River mile (RM) 96.0, downstream to Long Lake dam at RM 32.5. Figure 1 shows the river system and an outline the boundaries of the City of Spokane.

The Washington Department of Ecology (Ecology) is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). As a result, Ecology and the Corps of Engineers funded a study to develop a water quality and hydrodynamic model of …

Ce-Qual-W2: A Two-Dimensional, Laterally Averaged, Hydrodynamic And Water Quality Model, Version 3.1, Thomas M. Cole, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

CE-QUAL-W2 is a two-dimensional, longitudinal/vertical, hydrodynamic and water quality model. Because the model assumes lateral homogeneity, it is best suited for relatively long and narrow waterbodies exhibiting longitudinal and vertical water quality gradients. The model has been applied to rivers, lakes, reservoirs, estuaries, and combinations thereof.

The application of CE-QUAL-W2 requires knowledge in the following areas: 1. Hydrodynamics 2. Aquatic biology 3. Aquatic chemistry 4. Numerical methods 5. Computers and FORTRAN coding 6. Statistics 7. Data assembly and reconstruction.

Water quality modeling is in many ways an art requiring not only knowledge in these areas but also experience in their …

Upper Spokane River Model: Boundary Conditions And Model Setup, 2001, Spencer Slominski, Robert Leslie Annear, Chris Berger, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to:

• Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam for 2001 based on the calibration conducted for 1991 and 2000 data sets, (Annear et al, 2001).

• Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen …

Tmdls: Statistical Correlations Or Mechanistic Modeling?, Scott A. Wells, Thomas M. Cole

Civil and Environmental Engineering Faculty Publications and Presentations

In developing TMDL waste-load allocations for the Snake River-Reservoir system in Western Idaho and Eastern Oregon, determinations of the assimilative capacity of the system and the impact of pollutant reduction strategies has been performed using both a statistical-correlation approach and a mechanistic modeling approach. The system included the Lower Snake River, Brownlee Reservoir, Oxbow Reservoir, and Hells Canyon Reservoir with the focus was on Brownlee Reservoir.

The statistical approach used on Brownlee Reservoir divided the system into riverine and lacustrine zones. Field data were then averaged over season and location to provide statistical correlations, such as between total phosphorus (TP) …

The Bull Run River–Reservoir System Model, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Bull Run watershed is located 41.8 kilometers east of Portland, Oregon in the Mt. Hood National Forest and consists of two reservoirs supplying drinking water to over 840,000 people in the Portland metropolitan area. In March 1998 Steelhead and Spring Chinook were listed as threatened in the Lower Columbia basin under the Endangered Species Act. Historical reservoir operations during the summer released no water downstream resulting in stream temperatures exceeding the state water quality standard for salmonids. CE-QUAL-W2 Version 3 is a two-dimensional water quality and hydrodynamic model capable of modeling watersheds with interconnected rivers, reservoirs and estuaries. CE-QUAL-W2 …

Basis Of The Ce-Qual-W2 Version 3 River Basin Hydrodynamic And Water Quality Model, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

CE-QUAL-W2 Version 3, a 2-D (longitudinal-vertical) hydrodynamic and water quality model for river basins combining both river and stratified river-estuary and lake-reservoir flow, is a development product of the Waterways Experiment Station in Vicksburg, MS, USA. With the development and release of any revised or reformulated model codes, significant model validation is required. This includes comparison of model results to simple analytical solutions for hydrodynamics and water quality transport, as well as comparison to laboratory and field data. In this paper, the model is compared to numerous analytical solutions for mass transport (1- D advective mass transport) and hydrodynamics (impulsive …

Willamette River And Columbia River Waste Load Allocation Model, Chris Berger, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

A hydrodynamic and water quality model of the Lower Willamette River was developed to evaluate management alternatives designed to improve water quality. The Lower Willamette River is located in Oregon and drains a watershed covering 11500 square miles consisting of forested, agricultural, and urban lands. Inflows include treated municipal wastes and industrial effluents along with non-point sources from agricultural, silvicultural and urbanized land. The model was designed to address temperature, dissolved oxygen, algae, pH and bacteria concerns. The Corps of Engineers two-dimensional, laterally averaged, hydrodynamic and water quality model CE-QUAL-W2, Version 3 was applied. CE-QUAL-W2 consists of directly coupled hydrodynamic …

Upper Spokane River Model: Model Calibration, 1991 And 2000, Chris Berger, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to:

• Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics)

This report evaluates the model calibration and discusses issues relative to that calibration effort. …

Validation Of The Ce-Qual-W2 Version 3 River Basin Hydrodynamic And Water Quality Model, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

CE-QUAL-W2 Version 3, a 2-D (longitudinal-vertical) hydrodynamic and water quality model for river basins combining both river and stratified river-estuary and lakereservoir flow, is a development product of the Waterways Experiment Station in Vicksburg, MS, USA. With the development and release of any revised or reformulated model codes, significant model validation is required. This includes comparison of model results to simple analytical solutions for hydrodynamics and water quality transport, as well as comparison to laboratory and field data. In this paper, the model is compared to numerous analytical solutions for mass transport (1-D advective mass transport) and hydrodynamics (impulsive wind …

Lower Willamette River Model: Model Calibration, Chris Berger, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

Water Environment Services of Clackamas County is in the process of planning upgrades on several of its wastewater treatment plants (WWTPs) which discharge into the Lower Willamette River. The goals of the modeling effort were to:

• Gather data to construct a computer simulation model of the Lower Willamette River system in order to evaluate the impact of the WWTP discharges on water quality

• Ensure that the model accurately represents the system physics and chemistry (flow, temperature, dissolved oxygen and nutrient dynamics) by model calibration

• Use the model to evaluate how to meet various future discharge scenarios for …

Upper Spokane River Model: Boundary Conditions And Model Setup, 1991 And 2000, Robert Leslie Annear, Chris Berger, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to:

• Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam

• Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics)

A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied …

Lower Willamette River Model: Boundary Conditions And Model Setup, Herman G. Rodriguez, Robert Leslie Annear, Scott A. Wells, Chris Berger

Civil and Environmental Engineering Faculty Publications and Presentations

Water Environment Services of Clackamas County is in the process of planning upgrades on several of its sewage treatment plants which discharge into the Lower Willamette River. The goals of the modeling effort are to:

• Gather data to construct a computer simulation model of the Lower Willamette River system including part of the Lower Columbia River and the Willamette River above the Oregon City Falls; Because of the tidal influence in the Lower Willamette River, portions of the Columbia River that might affect the Lower Willamette River water quality were also modeled. Also, a section of the Willamette River …

Theoretical Basis For The Ce-Qual-W2 River Basin Model, Scott A. Wells, Thomas M. Cole

Civil and Environmental Engineering Faculty Publications and Presentations

The primary objective of this research is to integrate a riverine model into the existing W2 code that would provide the capability for modeling entire watersheds. This task was accomplished by the following steps:

• Formal derivation of governing equations and solution algorithm with general channel slope

• Detailed analysis of algorithm for linking branches and smooth implementation of boundary conditions between branches

• Algorithm development and changes to basic model code (including branch definitions with slope, slope correction to solution algorithm, transfer of momentum between internal branches)

These tasks were performed with the following constraints and initiatives:

• Utilize …

Ce-Qual-W2, Version 3, Scott A. Wells, Thomas M. Cole

Civil and Environmental Engineering Faculty Publications and Presentations

CE-QUAL-W2 is a two-dimensional water quality and hydrodynamic code supported by the U.S. Army Engineer Research and Development Center (Cole and Buchak 1995). The model has been widely applied to stratified surface water systems such as lakes, reservoirs, and estuaries and computes water levels, horizontal and vertical velocities, temperature, and 21 other water quality parameters (such as dissolved oxygen, nutrients, organic matter, algae, pH, the carbonate cycle, bacteria, and dissolved and suspended solids). A typical model grid is shown in Figure 1 where the vertical axis is aligned with gravity.

This technical note documents the development of CE-QUAL-W2, Version 3, …

Modeling The Bull Run River-Reservoir System, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The City of Portland, Water Bureau currently operates 2 Bull Run reservoirs, Reservoir #2 and Reservoir #1 as a water supply source in the Bull Run watershed shown in Figure 1 and Figure 2. The Water Bureau wants to operate their water supply system in order to meet both water supply objectives and fish habitat objectives downstream of the Bull Run reservoirs in Bull Run River. In addition, a third Bull Run reservoir has been proposed as an additional water supply source. This reservoir also may be used to meet water supply and fish habitat objectives in Bull Run River. …

Ce-Qual-W2 Version 3: Hydrodynamic And Water Quality River Basin Modeling, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

CE-QUAL-W2 is a two-dimensional (longitudinal-vertical) water quality and hydrodynamic computer simulation model that was originally developed for deep, long, and narrow waterbodies. The current model, Version 2, has been used in over 200 river, reservoir/lake, and estuary applications throughout the U.S. and abroad. Version 2, though, cannot accommodate systems that have a significant sloping water surface since the vertical coordinate system is aligned with gravity and vertical accelerations are neglected. The governing equations for CE-QUAL-W2 were re-derived so that it could be applied to entire river basins including river-estuary, lake-river, and reservoir-river systems with channel slopes. This re-derivation is one …

Variation Of Constitutive Model Formulation On Analytical Cake Filtration Models, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

Constitutive properties are required to model porosity, effective stress, porewater pressure, or permeability during cake filtration. By using an analytical cake filtration model based on Tiller (1975) with various constitutive property formulations, predictions of effective stress, permeability, and porosity distributions in a filter cake can be made. This analytical approach was only valid when spatially average values of porosity and pressure differential were constant over time. Several different constitutive property formulations were compared to data of effective stress and permeability as a function of porosity for kaolin clay in water. Also the spatial distribution of porosity in a filter cake …

Modeling Macrophytes Of The Columbia Slough, Oregon, Chris Berger, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Columbia Slough is a tidally influenced freshwater system of wetlands, channels, and lakes located within the Portland, Oregon metropolitan area at the confluence of the Willamette and Columbia Rivers. It is a eutrophic water body susceptible to algae blooms and crashes and periods of high pH which violate water quality standards. High nutrient loads from groundwater principally controls algae productivity. Past structural changes to the Columbia Slough have included filling of wetlands and lakes and the construction of levees, dikes, culverts and irrigation channels. These changes have altered the natural flow dynamics creating an environment more conducive to eutrophication. …

Continuous Deflection Separation Of Stormwater Particulates, Tracy S. Schwarz, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

Capture of stormwater particulate matter is of concern to watershed managers trying to meet water quality guidelines by removing toxics associated with particulates from natural water bodies. A laboratory investigation into particle removal efficiency of a prototype Continuous Deflective Separation (CDS) device was made in the laboratory. Particle size distributions were obtained for roadway drainage surfaces. These distributions were used to assess the predicted performance of a CDS unit in the field.

Flow rates in the laboratory tests ranged from 125 GPM (7.9 l/s) to 270 GPM (17.0 l/s). Screen sizes used for testing were 1200 m and 2400 m. …

Analytical Modeling Of Cake Filtration, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The specific resistance model of cake filtration is based on the assumption that the average cake resistance is constant over time. This implies also that the spatially average values of porosity and pressure differential are also constant over time since specific resistance is a function of both parameters.

An analytical cake filtration model based on Tiller (1975) was derived using constitutive properties of kaolin suspensions in distilled water. Constitutive properties were determined by experiments performed using high-energy X-rays and porewater pressure probes to determine the spatial and temporal distributions of porosity and porewater pressure. Using these constitutive properties, predictions were …

Application Of Mathematical Modeling And Computer Simulation For Solving Water Quality Problems, Jacek Makinia, Scott A. Wells, David Crawford, Marian Kulbik

Civil and Environmental Engineering Faculty Publications and Presentations

Deteriorated water resources in Central and Eastern Europe call for actions that should be undertaken to improve current conditions and to protect human and environmental health. Mathematical modeling and computer simulation is often an integral part of the decision-making process. Models and simulations allow rapid and varied evaluation of causes and effects and the principal advantage is that they enable an analysis of even long-term actions with limited investment costs. This paper provides an overview of popular models used for simulation of major elements of a water quality system: surface water quality (QUAL2E), wastewater treatment (Activated Sludge Model No.1), sewer …

Filtration Modeling Of A Plate-And-Frame Press, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The porosity distribution and filtrate production during cake filtration in a plate-and-frame filter press were simulated mathematically. The model considered filtration that occurs after the filling process, not filtration that occurs as the suspension fills the cell. Governing equations for the temporal porosity distribution were developed for a plateand- frame press. The governing equations were solved numerically using an alternating-direction-implicit scheme. Appropriate initial and boundary conditions were determined based on characteristics of the plate-and-frame press and of the suspension properties. Predicted porosity and velocity distributions were calculated for assumed constitutive parameters.

Modeling Density Currents In Circular Clarifiers, Scott A. Wells, David M. Laliberte

Civil and Environmental Engineering Faculty Publications and Presentations

Design of sedimentation tanks for solid-liquid separation is often dependent on assuming ideal flow conditions. But the geometry of the tank and density currents as a result of temperature and suspended solids influences the fluid mechanics of the tank and can result in significant deviations from ideal flow.

A two-dimensional radial flow model was proposed which incorporated the effect of density currents resulting from temperature and suspended solids differentials within the tank. The numerical model predicted the steady-state, layer-averaged radial flow and layer depth.

The model solution and field data showed that the momentum and suspended solids of the inflow …

Gravity Drainage Prior To Cake Filtration, Scott A. Wells, Gregory K. Savage

Civil and Environmental Engineering Faculty Publications and Presentations

During the initial stages of a Buchner funnel or specific resistance test, gravity drainage occurs prior to application of the pressure differential. Some allow time for a small cake to form by gravity drainage. Filtrate data from the gravity drainage period can be used to determine constitutive properties of the cake under a hydrostatic pressure gradient. The constitutive properties that define the structure of the cake include the permeability and porosity as functions of the applied stress. Equations governing the drainage rate during a gravity filtration experiment assuming a constant and a non-constant average cake permeability and cake porosity were …

Review Of The United States Environmental Protection Agency Superfund Technical Assistance Grant Program, Robert Leslie Annear, Scott A. Wells, Shuguang Li, Marvin Beeson, Michael L. Cummings, Richard Pratt

Civil and Environmental Engineering Faculty Publications and Presentations

The EPA Technical Assistance Grant Program has been around for several years, but there are not many examples of its use in the Pacific Northwest from which citizens can learn from when considering applying for a Technical Assistance Grant. The EPA program is designed to provide citizens with technical assistance in understanding the issues related to a Superfund site (or proposed Superfund site) in their community. This report provides an overview of the Technical Assistance Grant Program with information on applying for the grant, selecting a Technical Advisor and managing the grant. Additionally two case studies are reviewed in order …

The Columbia Slough, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

This report was written in an attempt to provide the public and Bureau of Environmental Services Staff with a summary of work accomplished on the Columbia Slough system by Portland State University and other consultants working on the Slough over the last 6 years. An attempt was made to create an easy-to-read report with important overviews of the "big picture", glossary of definitions, index, and further details to assist in technology transfer.

Impact Of Groundwater Contamination In East Multnomah County On The Interlachen Community, Scott A. Wells, Shuguang Li, Marvin Beeson, Michael L. Cummings, Richard Pratt, Robert Leslie Annear, Karann Brandt

Civil and Environmental Engineering Faculty Publications and Presentations

The Friends of Blue and Fairview Lake through the Environmental Protection Agency (EPA) Technical Assistance Grant (TAG) program contracted with Portland State University faculty and staff to provide an independent review of the groundwater contamination problem at the Boeing-Cascade site in East Multnomah County. An independent consultant, Karann Brandt, of PRC Environmental Management, Inc., was also assisting the panel with the review.

The region of groundwater contamination is a 2.5 square mile region bounded by NE Halsey Blvd. to the Columbia River and NE 178th to NE 223rd (see Figure 1). The groundwater contamination is primarily of volatile organic compounds …