Geology Commons^™

Effect Of Ionic Strength On Gelation Time And Strength Of Amps-Based Polymer Gels, Maryam Sharifi Paroushi, Xuyang Tian, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Polymer gel treatment has been widely applied for improving sweep efficiency and controlling excessive water and gas production. Their performance depends on gelation time and final gel strength. In most studies, brine salinity is used to describe the effect of formation water on gel behavior. However, changing salinity also changes ionic strength and ion composition at the same time. Because of this coupling, it is difficult to identify the mechanisms controlling gelation, which has led to inconsistent trends in the literature. Increasing salinity has been reported to either slow or accelerate gelation and to weaken or strengthen gels depending on …

Evaluation Of Chromium-Crosslinked Amps-Hpam Copolymer Gels: Effects Of Key Parameters On Gelation Time And Strength, Maryam Sharifi Paroushi, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Controlling CO₂ channeling in heterogeneous reservoirs remains a major challenge for both enhanced oil recovery (EOR) and secure geological storage. AMPS-HPAM copolymers exhibit high-temperature resistance and brine tolerance compared with conventional HPAM gels, making them well suited for the harsh environments associated with CO₂ injection. Chromium-based crosslinkers (CrAc and CrCl₃) were investigated because sulfonic acid groups in AMPS can coordinate with trivalent chromium ions, enabling dual ionic crosslinking and the formation of a robust gel network. While organic crosslinked AMPS-HPAM gels have been widely studied, the behavior of chromium-crosslinked AMPS-containing systems, particularly their gelation kinetics under …

Evaluation Of A Novel Re-Crosslinkable Preformed Particle Gel For Conformance Control In Ultra-High Temperature Reservoirs, Yanbo Liu, Tao Song, Caleb Kwasi Darko, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

Preferential fluid flow remains a major challenge in subsurface energy production and gas storage operations, resulting in excessive water production in mature oil fields, reduced heat extraction in geothermal reservoirs, and low sweep and storage efficiency in CO₂-EOR projects. Polymer gels are widely used to mitigate high-permeability channels; however, conventional systems exhibit limited plugging efficiency and short lifetimes in ultra-high-temperature reservoirs due to poor thermal stability. This study presents a novel ultra-high-temperature-resistant preformed particle gel (UHT-PPG) developed for conformance control in reservoirs with temperatures of 150–275 °C and severe super-K or channeling problems. The material was evaluated in …

Laboratory Investigation Of High-Temperature Preformed Particle Gels For Fluid Control In Granite Cores For Geothermal Applications, K. Caleb Darko, Yanbo Liu, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

To understand the applicability of high-temperature preformed particle gel (HT-PPG) for control of short-circuiting in enhanced geothermal systems (EGSs), core flooding experiments were conducted on fractured granite cores under varying fracture widths, gel particle sizes and swelling ratios. Key parameters such as injection pressure, water breakthrough pressure, and residual resistance factor were measured to evaluate HT-PPG performance. The gel exhibited strong injectability, entering granite fractures at pressure gradients as low as 0.656 MPa/m; HT-PPG yields a superior sealing performance by significantly reducing the permeability; and dehydration occurs during HT-PPG propagation, with a dehydration ratio ranging from 4.71% to 11.36%. This …

Characterization And Leaching Feasibility Studies Of Copper Flue Dust For The Recovery Of Main And Trace Metals, Fardis Nakhaei, Marek Locmelis, Lana Alagha, Michael S. Moats, Carlos Eyzaguirre, Cory Smith

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Although copper smelter dust (CSD) is classified as hazardous waste, it also serves as a valuable secondary resource, offering potential for the recovery of critical elements. In this study, CSD samples were collected from the waste heat boiler (WHB) and electrostatic precipitator (ESP) units connected to the flash smelting furnace at a copper smelter. The representative samples were extensively characterized by particle size, and chemical and mineralogical analyses. Following sample characterization, leaching experiments were performed to evaluate the potential extraction of Cu, Fe, As, Zn, Pb, In, Ga, and Ge from the flue dusts. Distilled water, H2SO4, and HCl were …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

Novel Re-Crosslinkable Preformed Particle Gels (Rppg) For Parent- And Infill-Well-Fracture Interactions Mitigation, Xiaojing Ge, Adel Alotibi, Ahmed Al-Hlaichi, Yanbo Liu, Tao Song, Junchen Liu, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Hydraulic fracturing treatments in unconventional infill (or "child") wells can be significantly affected by depletion from existing parent-well, resulting in asymmetrical fracture growth. These issues may lead to excessive load-water production, proppant deposition, casing deformation in the parent well, and unbalanced stimulation of infill wells. To mitigate these effects, various strategies have been proposed, including the use of far-field diverters in child wells and repressurization of parent wells. Additionally, an increasingly popular strategy involves injecting near-wellbore diverters to temporarily plug entry points into the parent wellbores during frac operations on infill wells. To achieve better application, a novel low-cost, self-degradable, …

Thermal Alteration Of The Mineralogy Of Calcium Sulfoaluminate Cements: Implications For The Performance Of Rapid Repair Materials, Jillian Cavellier

Theses and Dissertations--Earth and Environmental Sciences

Calcium sulfoaluminate (CSA) was developed in part to lessen the environmental impact of cementitious materials compared to traditional Portland cements. CSA was first put into production in the 1970s and has been undergoing various performance testing to investigate its durability. Yet to be evaluated is CSA’s response to a rapid, high temperature event. In this study, X-ray diffraction, thermogravimetric analysis, Fourier transform infrared spectrometry and scanning electron microscope imaging were used to analyze alterations in the mineralogy due to such an event. As found in previous studies, after ~125°C, ettringite has been completely dehydrated. Ettringite decomposes into bassanite and calcium …

Dual Crosslinked Poly(Acrylamide-Co-N-Vinylpyrrolidone) Microspheres With Re-Crosslinking Ability For Fossil Energy Recovery, Jingyang Pu, Baojun Bai, Jiaming Geng, Na Zhang, Thomas Schuman

Chemical and Biochemical Engineering Faculty Research & Creative Works

Microspheres have been proposed to be applied in controlling wastewater production for mature oilfields and migrating leakage for gas and nuclear waste storage. However, it remains challenging for stacked microspheres to maintain strong blocking ability in micron-sized small pores or fractures. in this study, a novel microsphere was developed with comprehensive properties including high deformability and long re-crosslinking time upon tunable swelling ratio for the applications. a dual covalent and physical crosslinking strategy was used to develop novel microspheres reinforced by a hydrogen bond (H-bond, between pyrrole ring and amide group) and coordination bond (between chromium acetate (CrAc) and carboxyl …

Findings Report: Virtual Workshop On ‘Resilient Supply Of Critical Minerals’, Marek Locmelis, Angela D. Lueking, Michael S. Moats, Kwame Awuah-Offei, Lana Z. Alagha, Mark W. Fitch, Alanna Krolikowski, Shelby Clark

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Executive Summary
On August 2-3, 2021, the Thomas J. O’Keefe Institute for Sustainable Supply of Strategic Minerals at Missouri University of Science and Technology (Missouri S&T) hosted the NSF-funded virtual workshop ‘Resilient Supply of Critical Minerals’. The workshop was convened via Zoom and attracted 158 registrants, including 108 registrants from academia (61 students), 30 registrants from government agencies, and 20 registrants from the private sector. Four topical sessions were covered:

A. Mineral Exploration and Source Diversification.
B. Supply Chain and Policy Issues.
C. Improving Mineral Recycling and Reprocessing Technologies.
D. Technological Alternatives to Critical Minerals.

Each topical session was composed …

Upgrading Biogas Using Eburru Zeolitic Rocks And Other Adsorbent Materials To Remove Carbon Dioxide And Hydrogen Sulphide, James K Mbugua, Joseph M Mwaniki, Damaris M Nduta, Francis B Mwaura

Tanzania Journal of Science

The trace amounts of carbon dioxide and hydrogen sulfide in raw biogas lower its calorific value,cause corrosion and make it hard to compress biogas into the cylinder. Raw biogas was obtainedfrom anaerobic digestion of cow dung and market wastes. The gas was stored in tubes or urine bagbefore upgrading. Natural zeolite rocks, maize cobs, steel wire, desulphurizer, and worn-out tyreswere used as the upgrade materials. The composition of biogas was recorded before and afterupgrading using a GP180 portable biogas analyzer from Henan, China. The measured level of rawbiogas was 0.0227% H2S, >20% CO2 and 52-56% CH4. The most efficient upgrade …

Cmas/Volcanic Ash Infiltration Performance Of Yttria Rich-Zirconia Thermal Barrier Coatings Produced By Electron Beam Physical Vapor Deposition, Juan Jose Gomez Chavez

Open Access Theses & Dissertations

For many years the use of thermal barrier coatings (TBC) in gas turbine engines has allowed a significant increase in engine operating temperatures which are above the Ni-based super alloys' melting point. The base material for TBCs is the state of the art 7 wt % yttria stabilized zirconia (YSZ) which provides the thermal protection. Current industry demands for increased engine efficiency has pushed TBCs to the limits where significant technological constrains have been identified. One of the main ones represents the high temperature corrosion of the TBC material due to the ingestion of silicate based airborne particles commonly referred …

A Novel Approach To Analyzing Strain Heterogeneity In Polycrystalline Quartz Specimens Deformed At High Pressure And Temperature, Nolan Ambrose Regis

UNLV Theses, Dissertations, Professional Papers, and Capstones

Rheological studies of rocks and minerals allow researchers to study the grain-scale deformation mechanisms that govern large-scale geologic processes from mountain building to mantle mixing. Deforming rock samples with high pressure and temperature apparatuses similar to the Griggs piston cylinder apparatus allows us to simulate deformation at depth. However, many apparatuses are limited to “cook-and-look” analysis and require modeling techniques to determine the evolution of deformation patterns found in experimental samples. A previous study used two-dimensional finite element models to analyze the development of stress and strain patterns in polycrystalline rocks. The study suggested rhythmic patterns in deformed rocks develop …

Pre-Construction Rock Treatment And Soil Modification Program Using Low Mobility Grout To Mitigate Future Sinkhole Development In A 2,787.1 Square Meter (30,000 Sf) Maintenance Facility, Steven W. Shifflett

Sinkhole Conference 2015

The US Army required construction of a 2,787.1 square meters (30,000 sf) maintenance facility supported on shallow foundations at the Fort Campbell Military Installation. During the subsurface investigation a seven foot air-filled void was encountered in the bedrock within the building footprint. Electrical Resistivity Imaging (ERI) was conducted in an attempt to determine the lateral extent of the encountered void and to establish the general prevalence of karst features at the site. Due to uncertainty in the subsurface conditions, a rock treatment and soil modification program was developed which consisted of a series of targeted exploratory grout holes advanced in …

Feasibility Study: The Evaluation Of Polymer Coatings To Prevent Weathering Of Weak Rocks, Lauren Distler

Senior Honors Projects, 2010-2019

The weathering and erosion of weak rocks along roadways can cause dangerous and potentially fatal rockfalls.   Various slope stabilization methods exist, but each presents a set of challenges and trade-offs.   The focus of the project is to understand the feasibility of utilizing of a polymerbased slope stabilization technique. Rock samples were collected along US Route 33 in Virginia and West Virginia, and preliminary tests were conducted to evaluate the absorption of water (% mass) and durability. The study evaluates three polymer options in regard to the following criteria: adhesion to rock, layer thickness, semi-permeability, insolubility, and non-toxicity. The polymer selection …

Influence Of Lithophysae Geometry On Mechanical Properties Of Hydro-Stone®, Moses Karakouzian, Doug Rigby

Publications (YM)

85 percent of YM drift tunnels will be constructed in lithophysal volcanic tuff. Rock behavior depends on porosity. Limited experimental data exists to characterize rock porosity and dependencies on properties such as σc , E, and n.

Properties Of Fired Bodies Made From Tanzanian Talc-Clay Mixes For Ceramic Applications., E. H. J. Lugwisha

Tanzania Journal of Science

Fired properties of talc-clay mixed bodies of different compositions were investigated for ceramic applications. Clays from Pugu and Malangali and talcs from two different sites in Kikombo deposits in Dodoma Region were used. Chemical analyses, X-ray analysis and Differential Thermal analysis for clays and talcs were used for the characterisation. Moulded mixed samples of clay and talc dried at room temperature at 1100C for 24 hours were fired at 1200, 1250, 1300 and 13500C for 6 hours. Both clay deposits consist mainly of kaolin. Talc1 - T1 is of higher purity than Talc - T2. Furthermore, the percentage shrinkage of …

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Experimental Investigation Of Time Dependent Behavior Of Welded Topopah Spring Tuff, Lumin Ma

Publications (YM)

Four types of laboratory tests have been performed. Specimens were attained from four lithophysal zones of the welded Topopah Spring Tuff unit at Yucca Mountain, Nevada: upper lithophysal, middle nonlithophysal, lower lithophysal and lower nonlithophysal zones. Two types of tests are conducted to study time-dependent behavior: constant strain rate and creep tests. Sixty five specimens from the middle nonlithophysal zone were tested at six strain rates: 10 , 10 , 10 , 10 , 10 , and 10 . Test durations range from 2 seconds to 7 days. Fourteen specimens from middle nonlithophysal, lower lithophysal and lower nonlithophysal zones are …

Stress Corrosion Cracking Studies, K. S. Raja, S. Namjoshi, Amy J. Smiecinski

Publications (YM)

This document reports on the activities for Task 17 of the U.S. DOE/UCCSN Cooperative Agreement Number DE-FC28-98NV12081. There are three subtasks in this Task, the experimental results, discussions, and conclusions of which are presented in the following sections. Data Sources and Electronic Data Control The Data Identification numbers for the data, graphs, and tables in this report, as submitted to the Data Management Database, are tabulated below. The table also includes the source files for the said data as well as the corresponding scientific notebooks where the data can be found. All data in the Q section of the report …

The Influence Of Halloysite Content On The Shear Strength Of Kaolinite, Reka Katalin Gabor

Dissertations and Theses

The objective of this thesis is to determine the relative shear strengths of halloysite, kaolinite, synthetic mixtures, and local soils, to investigate the influence of halloysite content on the shear strength of kaolinite, and to explore the possibility that the strength properties of soil clays might be controlled by the relative content of their component minerals.

X-Ray Irradiation Studies Of Lybian Desert Glass And Sand, Magdi M. Nasrallah

Archived Theses and Dissertations

No abstract provided.

Effects Of Oxygen Content Of Admitted Gases In Sulfide Flotation, Brian J. Boyle

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Methods Of Studying The Effects Of Frothers, Frank L. Bazzanella

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Habit Modification Of Naclo3 With Nai, William A. Coghlan

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Production Of Standard-Grade Ferromanganese In An Electric Arc Furnace, Force F. Baney Jr.

Bachelors Theses and Reports, 1928 - 1970

The investigations conducted in this project were essentially concerned with the effects of various compositions of two different slag systems upon the increased recovery of manganese in a standard-grade ferromanganese.

Investigation Of The Ternary System Silver-Aluminum-Indium (Ag-Al-In), Elvin H. Beardslee

Bachelors Theses and Reports, 1928 - 1970

This thesis paper contains material pertaining to & preliminary investigation of the ternary system Ag-Al-In. Procedures in this preliminary investigation are discussed in detail.

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Increased Corrosion Of A 304 Stainless Steel Upon Bending, William C. Tiddy

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.