Materials Chemistry Commons^™

Magnetic Properties Of Zgnrs With Nitrogen And Fluorine Adsorbates, A Computational Study, Justin Petit

Electronic Theses and Dissertations

Imposing dimensional restrictions on graphene sheets and adding impurities can give rise to carbon nanostructures with magnetic properties. In this work, zigzag graphene nanoribbons, zGNRs, with nitrogen and fluorine adatoms are investigated for magnetic properties of interest for spin devices. Geometry optimizations were done determining which position along a zGNR electrode that N and F would favorably attach to. Edge positions were determined as the most stable attachment site. M-cell zGNR electrodes (M = 1-3) edge-functionalized by N and F adatoms were investigated with respect to their band structures and spin densities in antiferromagnetic and ferromagnetic, AFM and FM, configurations. …

Development Of Graphene And Graphene Derivative Advanced Functional Additives: Mechanism And Application In Asphalt Formulations And Thermal Interface Management Materials, Dana Pinson

Dissertations

The overarching focus of my research is the use of graphene and graphene derivatives to enhance polymer properties. My first focus area was the prevention of oxidative degradation of asphalt through the incorporation of a graphene oxide (GO) -based nanoparticle filler to enhance oxygen barrier properties. Primary amine terminated polyisobutylene was synthesized via cationic polymerization followed by post polymerization chain end modification in a range of molecular weights and covalently grafted via the primary amine to graphene oxide aerogel (aGO) to create a polyisobutylene grafted graphene oxide (PIB-g-GO) nanoparticle. PIB-g-GO was then mixed into a substitute asphalt matrix at various …

Detection Of Nitrogen Dioxide Via Graphene-Enhanced Raman Scattering, Spencer Hazeslip

Chemistry & Biochemistry Undergraduate Honors Theses

This paper presents the development of a nitrogen dioxide (NO₂) sensor that utilizes the phenomenon of graphene-enhanced Raman scattering (GERS). The sensor consists of monolayer graphene on a silicon wafer, functionalized noncovalently with Copper(II) 2,9,16,23-tetra-tert-butyl-29H,31H-phthalocyanine (CuTTPc) via the solution soaking method. A custom sensing chamber was constructed to enable Raman spectra to be collected during NO₂ exposure. The response of the sensor was found to be linear between 10 and 100 ppm NO₂, indicating that it could be used for both detection and quantification. Furthermore, the sensor was shown to be reusable after …

Theoretical Investigation On Optical Properties Of 2d Materials And Mechanical Properties Of Polymer Composites At Molecular Level, Geeta Sachdeva

Dissertations, Master's Theses and Master's Reports

The field of two-dimensional (2D) layered materials provides a new platform for studying diverse physical phenomena that are scientifically interesting and relevant for technological applications. Theoretical predictions from atomically resolved computational simulations of 2D materials play a pivotal role in designing and advancing these developments. The focus of this thesis is 2D materials especially graphene and BN studied using density functional theory (DFT) and molecular dynamics (MD) simulations. In the first half of the thesis, the electronic structure and optical properties are discussed for graphene, antimonene, and borophene. It is found that the absorbance in (atomically flat) multilayer antimonene (group …

Ordered Mesoporous Carbon/Graphene/Nickel Foam For Flexible Dopamine Detection With Ultrahigh Sensitivity And Selectivity, Lai-Yu Wang, Xin Xi, Dong-Qing Wu, Xiong-Yu Liu, Wei Ji, Rui-Li Liu

Journal of Electrochemistry

Electro-catalytic reduction is an efficient way to achieve resourcable transformation of CO₂, which is one of the important techniques to solve the global environmental problems originated from excessive CO₂ emission. In this study, a membrane electrode assembly(MEA) type CO₂ electro-reduction electrolytic cell was constucted, which enables CO₂ feeding and real-time KHCO₃ aqueous updating on both sides of the cathode gas diffusion electrode (GDE). By means of the electrolytic cell, effects of KHCO₃ concentration and updating inside the liquid electrolytic chamber on CO₂ electro-reduction activity, production distribution and stability were investigated. The experimental …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Synthesis Of Graphene Using Plasma Etching And Atmospheric Pressure Annealing: Process And Sensor Development, Andrew Robert Graves

Graduate Theses, Dissertations, and Problem Reports (ETD)

Having been theorized in 1947, it was not until 2004 that graphene was first isolated. In the years since its isolation, graphene has been the subject of intense, world-wide study due to its incredibly diverse array of useful properties. Even though many billions of dollars have been spent on its development, graphene has yet to break out of the laboratory and penetrate mainstream industrial applications markets. This is because graphene faces a ‘grand challenge.’ Simply put, there is currently no method of manufacturing high-quality graphene on the industrial scale. This grand challenge looms particularly large for electronic applications where the …

Electrochemical Properties Of Sulfur In Different Carbon Support Materials, Bo Zhang, Jia Liu, Xiao-Chen Liu, De-Jun Li

Journal of Electrochemistry

In order to investigate the effect of carbon structure on electrochemical performance of sulfur/carbon composite in lithium-sulfur battery, in this paper, sublimation sulfur was incorporated into three types of carbon materials, namely, graphene, carbon black and porous carbon. The three sulfur/carbon composites were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), and X-ray diffraction (XRD) techniques, and their electrochemical performances were also studied. The results showed that the sulfur/porous carbon composite offered an initial discharge capacity of 1623.2 mA·h·g^-1 and remained 845 mA·h·g^-1 after 100 cycles. Compared with graphene and carbon black, the mesopores and micropores in porous …

Electropolymerization And Characterization Of Thin Film Dielectrics, Christopher White Ii

Department of Chemistry: Dissertations, Theses, and Student Research

Graphene is a two-dimensional allotrope of carbon, with several superlative properties, including high electron and hole conductivities, high tensile strength, and chemical robustness. Its chemical and physical properties make it attractive for in use in a myriad of applications, including transistors. However, graphene’s chemical inertness and its physical and electrical properties’ dependency on its conjugated structure make building composite materials with graphene difficult. In 2015, Lipatov, et. al. demonstrated that a film derived from electropolymerized phenol could be used as a dielectric layer on transistor devices fabricated from exfoliated graphene. This thesis extends that research, detailing experiments of phenol and …

Polymer Nanocomposites Containing High Aspect Ratio Particulates: Innovation In Co-Extruded Multilayer Barrier Films, Kevin Meyers

Dissertations

Delaminated montmorillonite (MMT) clay/ maleic anhydride grafted LLDPE nanocomposite multilayer films with alternating layers of LDPE were produced through multilayer co-extrusion. The MMT concentration within the nanocomposite layers was increased through annealing the films in the melt due to a mismatch in interdiffusion rates of the polymer layers. Analysis of the nanocomposite layers upon annealing revealed that the platelets impinged upon one another resulting in significant improvement in oxygen barrier in the multilayer system, exceeding the results of bulk nanocomposites.

Model analysis demonstrated that increasing the nanoplatelet aspect ratio or initial concentration in the filled layers would lead to even …

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …

Metal-Organic Frameworks And Graphene-Based Support Materials For Heterogeneous Catalysis, Andrew Lin

Theses and Dissertations

Nanoparticles are involved in a broad range of applications, including heterogeneous catalysis. Nanoparticles tend to quickly lose their well-defined shapes and facets due to aggregation under duress such as heat.

A series of highly studied materials are explored as support materials for nanoparticle supports. These supports include metal-organic frameworks (MOF), graphene oxide (GO), and a MOF-PRGO (partially reduced graphene oxide) hybrid. The inclusion of a support with the palladium increased lifespan of the catalyst by separation of nanoparticles. The choice of support material not only allowed for supporting of palladium nanoparticles, but allowed for rational catalyst synthesis in order to …

Photoluminescence Mechanism And Applications Of Graphene Quantum Dots, Yiyang Liu

Theses and Dissertations--Chemistry

Graphene quantum dots (GQDs) are small pieces of graphene oxide whose physical dimensions are so confined (a few to a few tens nm) that they have a finite bandgap due to a quantum confinement effect. The finite bandgap of GQDs grants them pronounced absorption bands and a substantial photoluminescence. These optical properties are rarely observed in traditional carbon materials, since most of carbon materials are metallic with a near-zero bandgap and thus have broad absorption spectra with no photoluminescence. The unique optical properties of GQDs, along with GQDs’ inherited advantages from carbon material family (cheap, abundant, non-toxic), make GQDs an …

Visible-Light-Responsible Co-Catalysts Enhanced By Graphene For Solar Energy Harvesting, Chen Ying

Masters Theses & Specialist Projects

This study focuses on the visible light response of hetero-structures of TiO2-graphene- MoS2 for solar energy harvestings. The commercial P25 TiO2 nano-particles, and selfprepared layered reduced graphene oxides (RG) and MoS2 were assembled for the targeted hetero-structure materials as visible-light responsible solar harvesting cocatalysts. The hydrothermal method was applied for nano-material synthesis, the reduction of graphene oxides, and bonding formation. Multiple characterization methods (SEM-TEM, XRD, XPS, UV-VIS, PL, FT-IR, TGA) have been applied to understand the electron-hole pair separation and recombination, and performance tuning in their visible-light photo-catalysis rhodamine B (Rh.B) degradations process

Compared to TiO2, an obvious red shift …

Toward High Performance Nanocarbon Fibers, Michaela R. Pfau

Master's Theses

High performance carbon fibers (CFs) have been a commercially available since their commercial boom in the 1970s, and are generally produced via carbonization of poly (acrylonitrile) (PAN). More recently, carbon nanomaterials like graphene and carbon nanotubes (CNTs) have been discovered and have shown excellent mechanical, thermal, and electrical properties due to their sp² carbon repeating structure. Graphene and CNTs can both be organized into macroscopic fibers using a number of different techniques, resulting in fibers with promising mechanical performance that can be readily multifunctionalized. In some cases, the two materials have been combined, and the resulting hybrid fibers have …

Electrochemical H2O2 Sensor Based On The Co-Immobilization Of Phosphmolybdic Acid And Graphene On Pedot Film Electrode With Nafion, Hao-Xian Zhou, Jun-Ming Zhang, Zhi-Yu Qu, Pan-Yu Zhang, You-Jun Fan

Journal of Electrochemistry

With a glassy carbon electrode (GCE) as the substrate, the poly(3,4-ethylenedioxythiophene) (PEDOT) film electrode was prepared through the electrochemical polymerization method, then a novel non-enzymatic electrochemical H₂O₂ sensor was fabricated by co-immobilizing phosphomolybdic acid and graphene with Nafion on the PEDOT/GCE electrode. The modified electrodes were characterized by scanning electron microscopy (SEM), while the responsive properties of the sensor to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results demonstrated that, under the optimized conditions, the sensor exhibited good electrocatalytic performance for H₂O₂ reduction. The current response of the sensor …

Electrochemical Syntheses Of Graphene And Its Composites, Bo Zhao, Li Jiang, Ming-Hui Yuen, Xian-Zhu Fu, Rong Sun, Ching-Ping Wong

Journal of Electrochemistry

Graphene is a kind of ideal two-dimensional flat carbon nanomaterials which have unique chemical and physical properties. The attractive potential applications must be based on the high quality mass production of graphene. However, it remains a huge challenge. An electrochemical approach is a fast, environmental friendly and easy-operating method. single- or multi-layered graphene flakes can easily be produced in short periods of time. In this review, the structure, properties and preparation methods of graphene are first introduced. Accordingly, the electrochemical approaches used for the productions of graphene flakes, graphene/inorganic nanocomposites, graphene/polymer composites and graphene analogues are highlighted. Finally, challenges and …

Synthesis And Electrochemical Performance Of Mn3O4/Graphene Composites, Shan-Shan Yang, Qian Zhang, Xiong-Gui Lin, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The Mn₃O₄/Graphene composites were synthesized by hydrothermal method with the in-situ redox reaction of graphene oxide (GO) and manganese acetate (Mn(Ac)₂). The phase structures and morphologies of the materials were characterized by XRD, SEM and TEM. The XPS and IR techniques were used for studying the residual function groups of reduced graphene oxide (RGO). The electrochemical performances of the hybrids were tested in a coin cell. Results showed that the composites prepared with the addition of ammonia water (RM-A) have better performance. The graphenes in RM-A were better-reduced and the Mn₃O_{4 …}

Synthesis Of Graphene Wrapped Li-Rich Layered Metal Oxide And Its Electrochemical Performance, Meng-Yan Hou, Ke Wang, Xiao-Li Dong, Yong-Yao Xia

Journal of Electrochemistry

In present work, lithium-rich layered transition metal oxide (LLO) was synthesized by a co-precipitation method in combination with a solid-state reaction. The graphene wrapped Li-rich layered oxide composite (LLO/Gra) was obtained by sintering the LLO/GO composite at 300 ^oC for 30 min in an air. The morphologies and the electrochemical performances were characterized by means of SEM, TEM, XRD, XPS, EIS and charge/discharge tests. The results indicated that the LLOe particles were uniformly wrapped with graphene. The resulting material exhibited better rate capability than that of pristine LLO since the wrapped graphene demonstrated the enhanced electronic conductivity. Accordingly, the …

Kinetic Study Of The Oxygen Reduction Reaction On Α-Ni(Oh)2 And Α-Ni(Oh)2 Supported On Graphene Oxide, Elaheh Farjami, L. Jay Deiner

Publications and Research

The kinetics of the oxygen reduction reaction on α-Ni(OH)2 and α-Ni(OH)2 supported on graphene oxide (α-Ni(OH)2/GO) were investigated using rotating disk linear sweep voltammetry in alkaline solutions of varying oxygen and hydroxyl concentrations. Over the full hydroxyl concentration range (0.05 M to 0.5M), α-Ni(OH)2/GO displayed higher activity than unsupported α-Ni(OH)2. The electron transfer numbers were 2.9 ± 0.2 for α-Ni(OH)2, 3.4 ± 0.1 for α-Ni(OH)2/GO at low [OH−], and 3.8–3.9 for α-Ni(OH)2/GO at high [OH−]. Compared to α-Ni(OH)2, α-Ni(OH)2/GO displayed higher chemical reaction rate constants and higher electron transfer rate constants. These differences suggest that the synergy between the α-Ni(OH)2 …

Fabrication And Characterization Of A Vertically-Oriented Graphene Supercapacitor, Patrick R. Rice, Jiaxin Cui, Ahmad Badr, Michael M. Oye, Jessica E. Koehne, Meyya Meyyappan

STAR Program Research Presentations

Supercapacitors, otherwise known as electrical double layer capacitors, are a new type of electrochemical capacitor whose storage capacity is governed by two principals: the electrostatic storage achieved by a separation of charge at the interface of an electrode with an electrolytic solution, and pseudocapacitance, whose electrical energy is achieved by faradaic redox reactions. This project reports the synthesis and characterization of vertically-oriented graphene grown on copper substrates as electrodes in electric double-layer capacitor. Graphene is a two-dimensional pure carbon material with a high potential for energy storage. With vertically-grown graphene, an exponentially-larger surface area is made available, allowing an increase …

Comparison In Factors Affecting Electrochemical Properties Of Thermal-Reduced Graphene Oxide For Supercapacitors, Peng Xiao, Da-Hui Wang, Jun-Wei Lang

Journal of Electrochemistry

In this paper, thermal-reduced graphene oxide (T-RGO) materials are synthesized by modified Hummer’s method, followed by thermal reduction under argon atmosphere at different temperatures. Electrochemical investigations show that, for T-RGO electrodes, good electrical conductivity is necessary and the surface functional groups play more significant role than the specific surface area in determining the electrochemical capacitance. The T-RGO obtained at 900 °C (T-RGO900) with a relatively high Brunauer-Emmett-Teller (BET) surface area (314 m²·g^-1) and a high electrical conductivity (2421 S·m^-1) shows a low specific capacitance of 56 F·g^-1. In comparison, the T-RGO obtained …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

Preparation And Electrochemical Behavior Of Pbo/Gn/Ac, Yun-Fang Gao, Yan-Ping Wang, Qiu-Shi Yao, Fu-Hua Wang, Dong-Lei Ren, Xin Xu

Journal of Electrochemistry

The lead oxide/graphene/activated carbon (PbO/GN/AC) composite materials were prepared by impregnating commercial activated carbon and graphene in saturated lead nitrate solution followed by calcination. The structures and morphologies of the composite were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results show that PbO crystals (about 200 nm) were dispersed uniformly on the surface of activated carbon and graphene. Electrochemical data indicate that the composite exhibited good electrochemical performances. The PbO/GN/AC composite possessed the higher over-potential of hydrogen evolution and the high specific capacitance of 312.6 F·g^-1, while the internal resistance …

Preparation Of Pt-Tio2/Graphene Composites With High Catalytic Activity Towards Methanol Oxidation And Oxygen Reduction Reaction, Li Qi, Ying Yin, Wen-Guang Tu, Bing-Bing Wu, Zhao-Sheng Wang, Jian-Guo Liu, Jun Gu, Zhi-Gang Zou

Journal of Electrochemistry

A series of graphene-supported TiO₂ nanoparticles (TiO₂/G) with different TiO₂ contents were prepared by a facile hydrothermal method, and then the Pt-TiO₂/G catalysts were successfully prepared by reducing Pt-precursor with microwave technique. Compared with Pt-G catalysts, the catalytic performance toward oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) of Pt-TiO₂/G catalysts was improved due to the addition of TiO₂. However, the excessive TiO₂ would lead to a poor catalytic performance of Pt-TiO₂/G catalysts because of the low electrical conductivity of TiO₂.

Polyaniline In Situ Grafted To Graphene Sheets, Erwin P. Enriquez, Elliard Roswell S. Yanza, Geoffrey Matthew C. Tan, Christine Joy Querebilo, Armando Somintac, Arnel Salvador

Chemistry Faculty Publications

Graphene is one of the most promising allotropes of carbon with wide applications in nanotechnology. Modification of graphene by chemical means can further expand its uses. Here, liquid-exfoliated graphene is functionalized with p-aminophenyl moiety using p-nitrophenyl diazonium salts which were diazotized in situ then reduced by tin(II) chloride. The aminophenyl-graphene thus produced is further modified to form polyaniline-graphene (PANI-GNH) by in situ oxidative graft polymerization of aniline using ammonium peroxydisulfate as oxidizing agent. The properties of the PANI-GNH were compared with polyaniline/graphene blends by Raman, infrared and UV-Visible spectroscopy, and cyclic voltammetry. Indeed, PANI-GNH registered different spectrochemical and electrochemical properties …

Fe, Co And Ni Adatoms Adsorbed On Silicene: A Dft Study, Kent Gang '14, Siva Gangavarapu '14, Matthew Deng '14, Glenn W. "Max" Mcgee, Ron Hurlbut, Michael Lee Dao Kang, Sean Ng Peng Nam, Harman Johll, Tok Eng Soon

Student Publications & Research

Two-dimensional materials have attracted much research attention given their intriguing properties. The latest member of this class of materials is silicene. In this work, we investigate the adsorption of Fe, Co and Ni adatoms on silicene using plane-wave density functional theory calculations within the Perdew-Burke-Ernzerhof parameterization of the generalized gradient approximation for the exchange-correlation potential. In particular, we calculate the binding energy, magnetization, and projected electronic configurations of these adatoms adsorbed at different sites on the silicene. Our calculations show that the hole site (i.e. in the centre of a hexagonal-like arrangement of Si atoms) is the most stable configuration …

Preparation, Characterization And Applications Of Functionalized Carbon Nano-Onions, Mahendra K. Sreeramoju

Theses and Dissertations--Chemistry

Carbon nano-onions (CNOs) discovered by Ugarte in 1992 are multi-layered fullerenes that are spherical analogs of multi-walled carbon nanotubes with diameters varying from 6 nm to 30 nm. Among the various methods of synthesis, CNOs prepared by graphitization of nanodiamonds (N-CNOs) and underwater electric arc of graphite rods (A-CNOs) are the subject of our research. N-CNOs are considered as more reactive than A-CNOs due to their smaller size, high curvature and surface defects.

This dissertation focuses on structural analysis and surface functionalization of N- CNOs with diameters ranging from 6—10 nm. Synthetic approaches such as oleum- assisted oxidation, Freidel-Crafts acylation …

The Electrochemical Properties Of 1-Pyrenebutyric Acid/Graphene Composites And Their Application In Glucose Biosensors, Min Wang, Jiong Wang, Fengbin Wang, Xinghua Xia

Journal of Electrochemistry

The electrochemical properties of 1-pyrenebutyric acid/graphene composites (PBA/G) obtained by one-step synthesis via π-π stacking was investigated. The electrochemical impedance titration curve shows the surface charge changes as function of solution pH by using ferricyanide/ferrocyanide redox couple as the probe. An apparent pK_a value is estimated as 6.2 according to the impedance titration curve. In addition, a glucose biosensor was constructed by immobilizing glucose oxidase (GOD) on the surface of PBA/G via covalent interaction. This biosensor shows a linear response to glucose within the concentration up to 5 mmol L^-1 with a detection limit of 0.085 mmol L …

Synthesis And Characterization Of Graphene Oxide, Jeremy A. Waddell, Arthur Cheng, Bin Chen

STAR Program Research Presentations

Graphene, a single atomic layer of sp² carbon atoms, has gotten a lot of attention from the scientific community because of its excellent mechanical and electronic properties. The mechanical exfoliation methods used to obtain graphene nanosheets are not effective for large scale manufacturing, so scalable synthesis approaches from structurally similar compounds are of great scientific interest. Graphene oxide is one such compound which is synthesized through the oxidation of graphite powder. The oxidation was performed using a modification of the previous experimental procedure. After synthesis, the powder was fabricated into graphene oxide films through vacuum filtration and transfer to …