Materials Chemistry Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Percolation-Induced Thermo-Rheological Transitions In Biobased Graphene Nanoplatelet Nanofluids, Abiodun A. Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Biobased lubricants with thermally responsive rheology are increasingly needed for high-efficiency mechanical systems. Graphene nanoplatelet (GnP) nanofluids in vegetable oils are promising candidates, yet their percolation-driven thermo-rheological transitions remain insufficiently understood. In particular, the coupled concentration–temperature landscape controlling network-mediated flow transitions has not previously been established. Here, surfactant-free GnP nanofluids were prepared in high-oleic soybean oil (HOSO) at concentrations of 0.025–2.15% v/v (ϕ), and their rheological response was mapped between 25°C and 80 °C under steady-shear and oscillatory conditions. Below the percolation threshold (ɸ ≤ 0.1% v/v), the nanofluids exhibit near-Newtonian behavior, moderate reversible viscosity enhancement, and classical Arrhenius-type temperature …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Assessing Passenger Electric Vehicle Growth Strategies And Their Impacts On Electricity Demand Load And Co2 Emissions In Aceh Province To Achieve Net Zero Emission Target By 2060, Taufik Hidayat, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

The electrification of the transport sector is a crucial pathway for achieving Indonesia’s Net Zero Emissions (NZE) target by 2060. This study assesses the potential impact of passenger electric vehicle (EV) penetration on electricity demand and CO2 emissions in Aceh Province through a scenario-based modelling approach. Two policy-aligned scenarios are assessed: a low-penetration (LP) scenario and a high-penetration (HP) scenario. Using the Gompertz model and the ASIF framework, total CO2 emissions were projected from 2020 to 2060. Results show that although higher EV penetration reduces direct emissions from internal combustion engine (ICE) vehicles, total CO2 emissions increase more significantly under …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Correlation Between Microstructure And Hardfacing Properties With Welding Current Intensity In Reconditioned Low-Alloy Steel Material Using Submerged Arc Welding (Saw) : A Comprehensive Review, Iman Nugraha Asmara, Winarto Winarto

Journal of Materials Exploration and Findings

This review studying the correlation between microstructural transformations and mechanical properties in reconditioned low-allow steel material, focusing on the impact of Submerged Arc Welding (SAW) parameters, especially current, on microstructure . The study highlights how variation on welding parameters, especially current intensity variation, affecting microstructural transformations, hardness, and wear resistance of hardfaced layers. Key aspects such as dilution effect, phases distribution, and carbide formation are reviewed to understanding their impact on mechanical properties. By reviewing insights from existing literature and experimental findings, this review underscores the role of Submerged Arc Welding in enhancing mechanical properties and microstructural of low-alloy steel …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Wear Of High Entropy Alloys: Understanding Effects Of Cryogenic Temperatures And Surface Nitriding On Wear Behavior, Aubrey Yu Tang

Dartmouth College Ph.D Dissertations

Cryogenic tribological applications have become increasingly important with the development and innovation of advanced equipment in aerospace, polar regions, superconductivity, and more. Traditional lubrication methods are not viable under these harsh environments, so metallic materials must be able to maintain excellent mechanical properties and withstand the constant impact and wear alone. High entropy alloys (HEAs) have emerged as potential candidates for these applications because of their wide variety of excellent room temperature properties and apparent improvement of mechanical properties of some HEAs at extremely low temperatures. Despite their promising nature, very limited work has been done on understanding the wear …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Additive Manufacturing Of Thermoplastic Composites, Matik Heskin, K. Chandrashekhara, Richard Billo, Ming-Chuan Leu, Thomas P. Schuman

Miners Solving for Tomorrow Research Conference

No abstract provided.

Mechanical And Thermal Characterization Of Additively Manufactured Carbon/Nylon 12 And Carbon/Peek Composites, Matik Heskin, Bradley Deuser, Thomas P. Schuman, K. Chandrashekhara, John Bayldon, Jeff Degrange, Steven Patterson, Neiko Levenhagen

Chemistry Faculty Research & Creative Works

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Thermo-Rheological And Tribological Properties Of Low- And High-Oleic Vegetable Oils As Sustainable Bio-Based Lubricants, Abiodun Saka, Tobechukwu K. Abor, Anthony C. Okafor, Monday U. Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Vegetable oil-based lubricants have attracted increased research attention in recent decades as sustainable alternatives to conventional petroleum-based lubricants in metal machining. However, more studies are required to fully elucidate the thermo-rheological and tribological properties. This study presents an investigation of the thermo-rheological and tribological properties of different vegetable oils, including low- and high-oleic soybean oil, high-oleic sunflower, safflower, and canola oils. The lubricity, and evolution of viscosity and thermodynamic properties as a function of temperature were investigated to obtain important parameters including the viscosity index, flow behavior index, flow activation energy, specific heat capacity, thermal conductivity, coefficient of friction, contact …

Effect Of Alkyd And Polyester Resin Compositions On Corrosion Resistance, Blistering, And Adhesion In Utilization Of Oily Sludge As Anti-Rust Coating Material, Gerets Land Kakalang, Yohanes David Kristianto, Johny Wahyuadi Mudaryoto

Journal of Materials Exploration and Findings

Oil sludge is a waste derived from upstream and downstream activities of the oil and gas industry which is estimated at 10,000 tonnes generated from all PERTAMINA downstream activities spread across various fields, processing units and depots throughout Indonesia. Oil sludge has the same characteristics as asphalt, where asphalt in previous studies can be used as an anti-rust coating, so that the handling of oily sludge can be topped up by reusing and having its own added value. The purpose of this research is to utilise waste oily sludge as an alternative anti-rust coating material and compare alkyd resin and …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Research On Development Status And Strategy Of Advanced Materials In Guangdong-Hong Kong-Macao Greater Bay Area, Ziwei Zhao, Can Wang, Weihua Wang, Qingli Huang

Bulletin of Chinese Academy of Sciences (Chinese Version)

Advanced materials are an important source of new quality productivity. Guangdong-Hong Kong-Macao Greater Bay Area is now facing the internal and external pressure of manufacturing upgrading, and there is an urgent need to play the leading and supporting role of advanced materials in the construction of modernized industrial system. This study combs through the basic situation of the development of materials science and industry in Guangdong-Hong Kong-Macao Greater Bay Area, analyzes its advantages, characteristics and problems in depth, and puts forward a number of suggestions around how to develop materials science, technology, and industry in the Greater Bay Area.

Studies Of Exotic Electronic, Optical, And Electrochemical Properties In Nanoparticle Assembly And Graphene, Jay Min Lim

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

It is well known that exotic properties and phenomena emerge as structural dimensions shrink to nanoscales. We self-assembled one-dimensional chains of gold nanoparticles in solution and quantified the growth process by monitoring the redshift of localized surface plasmon resonance (LSPR). Curiously, the redshift stopped while the chains continued to rearrange as manifested by gradual reduction in the LSPR peak. Using electromagnetic simulations, we quantitatively explained the phenomena as a rapid “addition-polymerization” followed by a sharp transition to “condensation-process.” Next, recognizing the significant electric field enhancement in the interparticle gap, a photoluminescent-active Eu³⁺ ion was used to probe Surface-Enhanced Photoluminescence …

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Zno Varistors—Preparation Of Nano And Micro Sized Powders By Mechanical Methods For Low And High Voltage Varistors, Maura Kelleher

Books/Book Chapters

ZnO-Bi2O3-Sb2O3 varistors are as essential today as they have been since their discovery five decades ago. Their role is to protect other electronic components against oncoming surges of electrons and survive. The demands on varistors are increasing. Electronic components are becoming smaller and more sensitive, and the metal oxides from which varistors are made are precious. Every aspect of their structure (macro, micro, nano and atomic) determines how they perform and survive. Each stage and variable within the powder metallurgy process is important. The mechanical methods in preparing nano and micro sized metal oxide powders are outlined in this chapter.

Investigation Of Space Charge Effects On Co2 Electrocatalytic Reduction On Gd-Doped Ceria Via Scanning Kelvin Probe And Model-Based Bayesian Analysis, Alejandro Mejia

Graduate Theses, Dissertations, and Problem Reports (ETD)

In studying novel energy conversion and storage systems, such as high-temperature electrolysis, numerous underlying fundamental physical processes remain unclear or inadequately understood. Among these, the modeling and comprehension of surface reaction mechanisms, coupled with the intricate effects of space‑charge interfaces, remains an unclear and challenging area of research.

The work of this dissertation involves the development of a 2D finite element analysis model, leveraging the robust MOOSE framework from INL. This model, featuring inhomogeneous defect thermodynamics for near-surface chemistry, formulated through Poisson‑Cahn variational theory, has been exploited for studying the electrocatalytic reduction of CO₂ on gadolinia doped ceria. The …