Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 17 of 17
Full-Text Articles in Physical Sciences and Mathematics
Tio2 Coated Three-Dimensional Hierarchically Ordered Porous Sulfur Electrode For The Lithium/Sulfur Rechargeable Batteries, Hongqiang Wang, Sha Li, Dan Li, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
Tio2 Coated Three-Dimensional Hierarchically Ordered Porous Sulfur Electrode For The Lithium/Sulfur Rechargeable Batteries, Hongqiang Wang, Sha Li, Dan Li, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
Australian Institute for Innovative Materials - Papers
A three-dimensional (3D) hierarchically ordered mesoporous carbon-sulfur composite slice coated with a thin TiO2 layer has been synthesized by a low-cost process and investigated as a cathode for the lithium-sulfur batteries. The TiO2 coated carbon sulfur composite thin slice works as a binder-free cathode without any current collectors for lithium-sulfur batteries. The hierarchical architecture provides a 3D conductive network for electron transfer, open channels for ion diffusion and strong confinement of soluble polysulfides. Meanwhile, TiO2 (titanium dioxide) coating layer could further effectively prevent the dissolution of polysulfides and also improve the strength of the entire electrode, thereby enhancing the electrochemical …
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Australian Institute for Innovative Materials - Papers
Mesoporous Co3O4 nanoplates were successfully prepared by the conversion of hexagonal beta-Co(OH)(2) nanoplates. TEM, HRTEM and N-2 sorption analysis confirmed the facet crystal structure and inner mesoporous architecture. When applied as anode materials for lithium storage in lithium ion batteries, mesoporous Co3O4 nanocrystals delivered a high specific capacity. At 10 degrees C current rate, as-prepared mesoporous Co3O4 nanoplates delivered a specific capacity of 1203 mAh/g at first cycle and after 200 cycles it can still maintain a satisfied value (330 mAh/g). Fromex-situ TEM, SAED and FESEM observation, it was found that mesoporous Co3O4 nanoplates were reduced to Li2O and Co …
Sulfur-Graphene Nanostructured Cathodes Via Ball-Milling For High-Performance Lithium-Sulfur Batteries, Jiantie Xu, Jianglan Shui, Jianli Wang, Min Wang, Hua-Kun Liu, S X. Dou, In-Yup Jeon, Jeong-Min Seo, Jong-Beom Baek, Liming Dai
Sulfur-Graphene Nanostructured Cathodes Via Ball-Milling For High-Performance Lithium-Sulfur Batteries, Jiantie Xu, Jianglan Shui, Jianli Wang, Min Wang, Hua-Kun Liu, S X. Dou, In-Yup Jeon, Jeong-Min Seo, Jong-Beom Baek, Liming Dai
Australian Institute for Innovative Materials - Papers
Although much progress has been made to develop high-performance lithium-sulfur batteries (LSBs), the reported physical or chemical routes to sulfur cathode materials are often multistep/complex and even involve environmentally hazardous reagents, and hence are infeasible for mass production. Here, we report a simple ball-milling technique to combine both the physical and chemical routes into a one-step process for low-cost, scalable, and eco-friendly production of graphene nanoplatelets (GnPs) edge-functionalized with sulfur (S-GnPs) as highly efficient LSB cathode materials of practical significance. LSBs based on the S-GnP cathode materials, produced by ball-milling 70 wt % sulfur and 30 wt % graphite, delivered …
Study On Vanadium Substitution To Iron In Li2fep 2o7 As Cathode Material For Lithium-Ion Batteries, Jiantie Xu, Shulei Chou, Qinfen Gu, M F. Md Din, Hua-Kun Liu, S X. Dou
Study On Vanadium Substitution To Iron In Li2fep 2o7 As Cathode Material For Lithium-Ion Batteries, Jiantie Xu, Shulei Chou, Qinfen Gu, M F. Md Din, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A series of Li2Fe1-3x/2VxP 2O7 (x = 0, 0.025, 0.05, 0.075, and 0.1) cathode materials for LIBs were prepared by the sol-gel method. Structural characterization of Li2Fe1-3x/2VxP2O7 (x = 0, 0.025, 0.05, 0.075, and 0.1) samples was conducted by synchrotron X-ray diffraction. The morphology and oxidation states of Fe2+ and V 3+ in the Li2Fe1-3x/2VxP 2O7 samples were confirmed by scanning electron microscopy and magnetic susceptibility measurements, respectively. The electrochemical measurements indicated that Li2Fe1-3x/2VxP 2O7 (x = 0.025) delivered the higher reversible capacity of 79.9 mAh g-1 at 1 C in the voltage range of 2.0 - 4.5 V with …
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Nano-Germanium/polypyrrole composite has been synthesized by chemical reduction method in aqueous solution. The Ge nanoparticles were directly coated on the surface of the polypyrrole. The morphology and structural properties of samples were determined by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Thermogravimetric analysis was carried out to determine the polypyrrole content. The electrochemical properties of the samples have been investigated and their suitability as anode materials for the lithium-ion battery was examined. The discharge capacity of the Ge nanoparticles calculated in the Ge-polypyrrole composite is 1014 mAh g-1 after 50 cycles at 0.2 C rate, which is …
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Australian Institute for Innovative Materials - Papers
Li1.16Mn1.84O4 nanoparticles (50-90 nm) with cubic spinel structure are synthesized by combining a microemulsion process to produce ultrafine Mn(OH)2 nanocrystals (3-8 nm) with a solid-state lithiation step. The nanostructured lithium-rich Li1.16Mn1.84O4 shows stable cycling performance and superior rate capabilities as compared with the corresponding bulk material, for example, the nano-sized Li1.16Mn1.84O4 electrode shows stable reversible capacities of 74 mAhg-1 during the 1000th cycle at a high rate of 40 C between 3.0 and 4.5 V. In addition, Li1.16Mn1.84O4 nanoparticles also show high Li storage properties over an enlarged voltage window of 2.0-4.5 V with high capacities and stable cyclability, for …
Electrode Nanostructures In Lithium-Based Batteries, Nasir Mahmood, Yanglong Hou
Electrode Nanostructures In Lithium-Based Batteries, Nasir Mahmood, Yanglong Hou
Australian Institute for Innovative Materials - Papers
Lithium-based batteries possessing energy densities much higher than those of the conventional batteries belong to the most promising class of future energy devices. However, there are some fundamental issues related to their electrodes which are big roadblocks in their applications to electric vehicles (EVs). Nanochemistry has advantageous roles to overcome these problems by defi ning new nanostructures of electrode materials. This review article will highlight the challenges associated with these chemistries both to bring high performance and longevity upon considering the working principles of the various types of lithium-based (Li-ion, Li-air and Li-S) batteries. Further, the review discusses the advantages …
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A high performance Li3V2(PO4)3 cathode material for lithium ion batteries was synthesized by the microwave-assisted hydrothermal method followed by a post annealing process. The synchrotron X-ray diffraction analysis results confirmed that single-phase Li3V2(PO4)3 with monoclinic structure was obtained. Scanning electron microscope and transmission electron microscope images revealed that the as-prepared Li3V 2(PO4)3 was composed of nanowires and microsized particles. Electrochemical results demonstrated that the Li 3V2(PO4)3 electrode measured at 10 C after 500 cycles can deliver discharge capacities of 85.4 mAh g-1 and 103.4 mAh g-1, with a capacity retention of 99.3% and 95.9%, in the voltage ranges of 3.0-4.3 …
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Multi-layer graphene sheets have been synthesized by a time-efficient microwave autoclave method and used to form composites in situ with single-walled carbon nanotubes. The application of these composites as flexible free-standing film electrodes was then investigated. According to the transmission electron microscopy and X-ray diffraction characterizations, the average d-spacing of the graphene-single-walled carbon nanotube composites was 0.41 nm, which was obviously larger than that of the as-prepared pure graphene (0.36 nm). The reversible Li-cycling properties of the free-standing films have been evaluated by galvanostatic discharge-charge cycling and electrochemical impedance spectroscopy. Results showed that the free-standing composite film with 70 wt% …
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Paper-like free-standing germanium (Ge) and single-walled carbon nanotube (SWCNT) composite anodes were synthesized by the vacuum filtration of Ge/SWCNT composites, which were prepared by a facile aqueous-based method. The samples were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Electrochemical measurements demonstrate that the Ge/SWCNT composite paper anode with the weight percentage of 32% Ge delivered a specific discharge capacity of 417 mA h g−1 after 40 cycles at a current density of 25 mA g−1, 117% higher than the pure SWCNT paper anode. The SWCNTs not only function as a flexible mechanical support for …
A Solvothermal Strategy: One-Step In Situ Synthesis Of Self-Assembled 3d Graphene-Based Composites With Enhanced Lithium Storage Capacity, Jingjing Ma, Jiulin Wang, Yu-Shi He, Xiao Zhen Liao, Jun Chen, Jiazhao Wang, Tao Yuan, Zi-Feng Ma
A Solvothermal Strategy: One-Step In Situ Synthesis Of Self-Assembled 3d Graphene-Based Composites With Enhanced Lithium Storage Capacity, Jingjing Ma, Jiulin Wang, Yu-Shi He, Xiao Zhen Liao, Jun Chen, Jiazhao Wang, Tao Yuan, Zi-Feng Ma
Australian Institute for Innovative Materials - Papers
A facile and controllable approach has been developed to synthesize three-dimensional (3D) graphene-based monoliths. Here, as a proof-of-concept experiment, self-assembled 3D CoO/graphene sheets (CoO/GS) composites with porous structures have been successfully fabricated in an ethanol medium by a one-step, in situ growth, solvothermal method. During the process, the in situ nucleation and growth of CoO particles on GS were tuned by the formation of a 3D GS network. In the as-prepared composites, the self-assembled 3D GS network around the CoO particles can not only provide a 3D conductive matrix, but also buffer the volume changes of CoO and restrain the …
High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang
High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Honeycomb-like pure sulfur architectures were synthesized by a cooperative self-assembly strategy, in which a soft template is used to form the porous structure. Their electrochemical performance is significantly improved comparing with the commercial sulfur powder and the as-prepared sulfur without honeycomb morphology. There has been no report on using a soft template to prepare honeycomb-like sulfur particles.
Porous Ni0.5zn0.5fe2o4 Nanospheres: Synthesis, Characterization, And Application For Lithium Storage, Min Zhang, Xuanwen Gao, Zhenfa Zi, Jianming Dai, Jiazhao Wang, Shulei Chou, Changhao Liang, Xuebin Zhu, Yuping Sun, Hua-Kun Liu
Porous Ni0.5zn0.5fe2o4 Nanospheres: Synthesis, Characterization, And Application For Lithium Storage, Min Zhang, Xuanwen Gao, Zhenfa Zi, Jianming Dai, Jiazhao Wang, Shulei Chou, Changhao Liang, Xuebin Zhu, Yuping Sun, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Monodisperse porous Ni0.5Zn0.5Fe2O4 nanospheres have been successfully synthesized by the solvothermal method. The diameter of the nanospheres can be tuned by controlling the reactant concentration. Lower reactant concentration is favoured for the synthesis of mesoporous Ni0.5Zn0.5Fe2O4 nanospheres with higher surface area. The electrochemical results show that mesoporous Ni0.5Zn0.5Fe2O4 nanospheres exhibit high reversible specific capacity (1110 mAh g-1) for Li storage and high capacity retention, with 700 mAh g-1 retained up to 50 cycles. The excellent electrochemical properties could be attributed to the large surface area and mesoporous structure. The results suggest that Ni0.5Zn0.5Fe2O4 could be a promising high capacity anode …
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Three-dimensional (3D) TiO2 nanotube arrays grown on Ti mesh were prepared via the anodization process. The diameters of the Ti and TiO 2/Ti wires and the length of the TiO2 nanotubes have linear relationships with the anodization processing time. When the anodization processing time is 600 min, the TiO2/Ti mesh anode materials showed good capacity retention and high specific area capacity, without the need for a current collector or binder, due to their high surface area, high substrate utilization, and large active material loading rate per unit area. At the current density of 50 μA cm-2, TiO2/Ti mesh with 600 …
Synthesis And Electrochemical Properties Of Wo3/C For Lithium Ion Batteries, Hong Gao, Shuijin S. Yang, Chuanqi Feng, Jiazhao Wang, Zaiping Guo
Synthesis And Electrochemical Properties Of Wo3/C For Lithium Ion Batteries, Hong Gao, Shuijin S. Yang, Chuanqi Feng, Jiazhao Wang, Zaiping Guo
Australian Institute for Innovative Materials - Papers
WO3/C nanorods were prepared by a combination of hydrothermal synthesis method and the solid phase reaction method, using (NH4)10H2(W2O7)6, H2C2O4·2H2O and glucose(carbon source) as raw materials. The effects of different proportions of glucose on the morphologies and electrochemical properties of the final products were systematically investigated. The results showed that the WO3/C nanorods prepared with the 10 wt.% glucose as carbon source exhibited the highest reversible specific capacity (807 mAh g-1) at current density …
Pristine Organo-Imido Polyoxometalates As An Anode For Lithium Ion Batteries, Rao Naumaan Nasim Khan, Nasir Mahmood, Chunlin Lv, Guohui Sima, Jin Zhang, Jian Hao, Yanglong Hou, Yongge Wei
Pristine Organo-Imido Polyoxometalates As An Anode For Lithium Ion Batteries, Rao Naumaan Nasim Khan, Nasir Mahmood, Chunlin Lv, Guohui Sima, Jin Zhang, Jian Hao, Yanglong Hou, Yongge Wei
Australian Institute for Innovative Materials - Papers
Here we have designed a strategy to improve the electronic conductivities of polyoxometalates (POMs) via property-oriented organic grafting for use in lithium-ion batteries (LIBs). POMs usually exhibit limited electronic conductivity that hinders their use in electronic applications. Organic grafting of POMs defines a valuable path for improving electronic conductivities of POMs, due to the enhanced metal to ligand charge transfer (MLCT) via d-π electronic interactions, and results in their feasible application in LIBs. Comparative practical and theoretical study of the effect of functional groups revealed that grafting of the remote electron withdrawing group (-SCN) on POMs via organo-imidoylization along with …
Graphene-Based Nanocomposites For Energy Storage And Conversion In Lithium Batteries, Supercapacitors And Fuel Cells, Nasir Mahmood, Chenzhen Zhang, Han Yin, Yanglong Hou
Graphene-Based Nanocomposites For Energy Storage And Conversion In Lithium Batteries, Supercapacitors And Fuel Cells, Nasir Mahmood, Chenzhen Zhang, Han Yin, Yanglong Hou
Australian Institute for Innovative Materials - Papers
Due to their unique properties, together with their ease of synthesis and functionalization, graphene-based materials have been showing great potential in energy storage and conversion. These hybrid structures display excellent material characteristics, including high carrier mobility, faster recombination rate and long-time stability. In this review, after a short introduction to graphene and its derivatives, we summarize the recent advances in the synthesis and applications of graphene and its derivatives in the fields of energy storage (lithium ion, lithium-air, lithium-sulphur batteries and supercapacitors) and conversion (oxygen reduction reaction for fuel cells). This article further highlights the working principles and problems hindering …