Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 16 of 16
Full-Text Articles in Physical Sciences and Mathematics
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Australian Institute for Innovative Materials - Papers
Mesoporous Co3O4 nanoplates were successfully prepared by the conversion of hexagonal beta-Co(OH)(2) nanoplates. TEM, HRTEM and N-2 sorption analysis confirmed the facet crystal structure and inner mesoporous architecture. When applied as anode materials for lithium storage in lithium ion batteries, mesoporous Co3O4 nanocrystals delivered a high specific capacity. At 10 degrees C current rate, as-prepared mesoporous Co3O4 nanoplates delivered a specific capacity of 1203 mAh/g at first cycle and after 200 cycles it can still maintain a satisfied value (330 mAh/g). Fromex-situ TEM, SAED and FESEM observation, it was found that mesoporous Co3O4 nanoplates were reduced to Li2O and Co …
Sulfur-Graphene Nanostructured Cathodes Via Ball-Milling For High-Performance Lithium-Sulfur Batteries, Jiantie Xu, Jianglan Shui, Jianli Wang, Min Wang, Hua-Kun Liu, S X. Dou, In-Yup Jeon, Jeong-Min Seo, Jong-Beom Baek, Liming Dai
Sulfur-Graphene Nanostructured Cathodes Via Ball-Milling For High-Performance Lithium-Sulfur Batteries, Jiantie Xu, Jianglan Shui, Jianli Wang, Min Wang, Hua-Kun Liu, S X. Dou, In-Yup Jeon, Jeong-Min Seo, Jong-Beom Baek, Liming Dai
Australian Institute for Innovative Materials - Papers
Although much progress has been made to develop high-performance lithium-sulfur batteries (LSBs), the reported physical or chemical routes to sulfur cathode materials are often multistep/complex and even involve environmentally hazardous reagents, and hence are infeasible for mass production. Here, we report a simple ball-milling technique to combine both the physical and chemical routes into a one-step process for low-cost, scalable, and eco-friendly production of graphene nanoplatelets (GnPs) edge-functionalized with sulfur (S-GnPs) as highly efficient LSB cathode materials of practical significance. LSBs based on the S-GnP cathode materials, produced by ball-milling 70 wt % sulfur and 30 wt % graphite, delivered …
Na3v2(Po4)3 Particles Partly Embedded In Carbon Nanofibers With Superb Kinetics For Ultra-High Power Sodium Ion Batteries, Junghoon Yang, Dongwook Han, Mi Ru Jo, Kyeongse Song, Yongil Kim, Shulei Chou, Hua-Kun Liu, Yong-Mook Kang
Na3v2(Po4)3 Particles Partly Embedded In Carbon Nanofibers With Superb Kinetics For Ultra-High Power Sodium Ion Batteries, Junghoon Yang, Dongwook Han, Mi Ru Jo, Kyeongse Song, Yongil Kim, Shulei Chou, Hua-Kun Liu, Yong-Mook Kang
Australian Institute for Innovative Materials - Papers
We here describe the extraordinary performance of NASICON Na3V2(PO4)3-carbon nanofiber (NVP-CNF) composites with ultra-high power and excellent cycling performance. NVP-CNFs are composed of CNFs at the center part and partly embedded NVP nanoparticles in the shell. We first report this unique morphology of NVP-CNFs for the electrode material of secondary batteries as well as for general energy conversion materials. Our NVP-CNFs show not only a high discharge capacity of approx. 88.9 mA h g-1 even at a high current density of 50 C but also approx. 93% cyclic retention property after …
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Nano-Germanium/polypyrrole composite has been synthesized by chemical reduction method in aqueous solution. The Ge nanoparticles were directly coated on the surface of the polypyrrole. The morphology and structural properties of samples were determined by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Thermogravimetric analysis was carried out to determine the polypyrrole content. The electrochemical properties of the samples have been investigated and their suitability as anode materials for the lithium-ion battery was examined. The discharge capacity of the Ge nanoparticles calculated in the Ge-polypyrrole composite is 1014 mAh g-1 after 50 cycles at 0.2 C rate, which is …
Large Scale Production Of Novel G-C3n4 Micro Strings With High Surface Area And Versatile Photodegradation Ability, Muhammad Nawaz Tahir, Chuanbao Cao, Faheem K. Butt, Sajid Butt, Faryal Idrees, Zulfiqar Ali, Imran Aslam, M Tanveer, Asif Mahmood, Nasir Mahmood
Large Scale Production Of Novel G-C3n4 Micro Strings With High Surface Area And Versatile Photodegradation Ability, Muhammad Nawaz Tahir, Chuanbao Cao, Faheem K. Butt, Sajid Butt, Faryal Idrees, Zulfiqar Ali, Imran Aslam, M Tanveer, Asif Mahmood, Nasir Mahmood
Australian Institute for Innovative Materials - Papers
An easy, scalable and environmentally benign chemical method has been developed to synthesize micro strings of graphitic-C3N4 (msg-C3N4) through pre-treatment of melamine with HNO 3 in alkaline solvent at low temperature. This methodology results in a unique string type morphology of msg-C3N4 with higher surface area. These msg-C3N4 micro strings were used as a photocatalyst under visible light for photodegradation of rhodamine B, methyl blue and methyl orange. The msg-C3N4 shows enhanced photodegradation efficiency due to its high surface area and favourable bandgap. The first order rate constant for msg-C3N4 was measured which confirms the higher performance of msg-C3N4 in …
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Australian Institute for Innovative Materials - Papers
Li1.16Mn1.84O4 nanoparticles (50-90 nm) with cubic spinel structure are synthesized by combining a microemulsion process to produce ultrafine Mn(OH)2 nanocrystals (3-8 nm) with a solid-state lithiation step. The nanostructured lithium-rich Li1.16Mn1.84O4 shows stable cycling performance and superior rate capabilities as compared with the corresponding bulk material, for example, the nano-sized Li1.16Mn1.84O4 electrode shows stable reversible capacities of 74 mAhg-1 during the 1000th cycle at a high rate of 40 C between 3.0 and 4.5 V. In addition, Li1.16Mn1.84O4 nanoparticles also show high Li storage properties over an enlarged voltage window of 2.0-4.5 V with high capacities and stable cyclability, for …
Achieving Single Domain Relaxor-Pt Crystals By High Temperature Poling, Fei Li, Linghang Wang, Li Jin, Zhuo Xu, Shujun Zhang
Achieving Single Domain Relaxor-Pt Crystals By High Temperature Poling, Fei Li, Linghang Wang, Li Jin, Zhuo Xu, Shujun Zhang
Australian Institute for Innovative Materials - Papers
Single domain relaxor-PT crystals are important from both fundamental and application viewpoints. Compared to domain engineered relaxor-PT crystals, however, single domain crystals are prone to cracking during poling. In this paper, based on the analysis of the cracking phenomenon in [001] poled tetragonal 0.25Pb(In0.5Nb0.5)O3-0.37Pb(Mg 1/3Nb2/3)O3-0.38PbTiO3 (PIN-PMN-PT) crystals, the non-180°ferroelastic domain switching was thought to be the dominant factor for cracking during the poling process. A high temperature poling technique, by which the domain switching can be greatly avoided, was proposed to achieve the single domain relaxor-PT crystals. By this poling approach, a quasi-single domain crystal was obtained without cracks. In …
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A high performance Li3V2(PO4)3 cathode material for lithium ion batteries was synthesized by the microwave-assisted hydrothermal method followed by a post annealing process. The synchrotron X-ray diffraction analysis results confirmed that single-phase Li3V2(PO4)3 with monoclinic structure was obtained. Scanning electron microscope and transmission electron microscope images revealed that the as-prepared Li3V 2(PO4)3 was composed of nanowires and microsized particles. Electrochemical results demonstrated that the Li 3V2(PO4)3 electrode measured at 10 C after 500 cycles can deliver discharge capacities of 85.4 mAh g-1 and 103.4 mAh g-1, with a capacity retention of 99.3% and 95.9%, in the voltage ranges of 3.0-4.3 …
Ultra-High Performance, High-Temperature Superconducting Wires Via Cost-Effective, Scalable, Co-Evaporation Process, Ho-Sup Kim, Sang-Soo Oh, Hong-Soo Ha, Dojun Youm, Seung-Hyun Moon, Jung Ho Kim, S X. Dou, Yoon-Uk Heo, Sung-Hun Wee, Amit Goyal
Ultra-High Performance, High-Temperature Superconducting Wires Via Cost-Effective, Scalable, Co-Evaporation Process, Ho-Sup Kim, Sang-Soo Oh, Hong-Soo Ha, Dojun Youm, Seung-Hyun Moon, Jung Ho Kim, S X. Dou, Yoon-Uk Heo, Sung-Hun Wee, Amit Goyal
Australian Institute for Innovative Materials - Papers
Long-length, high-temperature superconducting (HTS) wires capable of carrying high critical current, Ic, are required for a wide range of applications. Here, we report extremely high performance HTS wires based on 5 μm thick SmBa2Cu3O7 − δ (SmBCO) single layer films on textured metallic templates. SmBCO layer wires over 20 meters long were deposited by a cost-effective, scalable co-evaporation process using a batch-type drum in a dual chamber. All deposition parameters influencing the composition, phase, and texture of the films were optimized via a unique combinatorial method that is broadly applicable for co-evaporation of other promising complex materials containing several cations. …
Strain-Responsive Polyurethane/Pedot:Pss Elastomeric Composite Fibers With High Electrical Conductivity, Mohammad Ziabari Seyedin, Joselito M. Razal, Peter C. Innis, Gordon G. Wallace
Strain-Responsive Polyurethane/Pedot:Pss Elastomeric Composite Fibers With High Electrical Conductivity, Mohammad Ziabari Seyedin, Joselito M. Razal, Peter C. Innis, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
It is a challenge to retain the high stretchability of an elastomer when used in polymer composites. Likewise, the high conductivity of organic conductors is typically compromised when used as filler in composite systems. Here, it is possible to achieve elastomeric fiber composites with high electrical conductivity at relatively low loading of the conductor and, more importantly, to attain mechanical properties that are useful in strain-sensing applications. The preparation of homogenous composite formulations from polyurethane (PU) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) that are also processable by fiber wet-spinning techniques are systematically evaluated. With increasing PEDOT:PSS loading in the fiber composites, the Young's …
High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou
High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
Sodium-ion energy storage, including sodium-ion batteries (NIBs) and electrochemical capacitive storage (NICs), is considered as a promising alternative to lithium-ion energy storage. It is an intriguing prospect, especially for large-scale applications, owing to its low cost and abundance. MoS2 sodiation/desodiation with Na ions is based on the conversion reaction, which is not only able to deliver higher capacity than the intercalation reaction, but can also be applied in capacitive storage owing to its typically sloping charge/discharge curves. Here, NIBs and NICs based on a graphene composite (MoS2/G) were constructed. The enlarged d-spacing, a contribution of the graphene matrix, and the …
High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang
High Performance Pure Sulfur Honeycomb-Like Architectures Synthesized By A Cooperative Self-Assembly Strategy For Lithium Sulfur Batteries, Xin Liang, Mohammad Kaiser, Konstantin Konstantinov, Richard Tandiono, Zhaoxiang Prof Zhaoxiang Wang, Hua-Kun Liu, S X. Dou, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Honeycomb-like pure sulfur architectures were synthesized by a cooperative self-assembly strategy, in which a soft template is used to form the porous structure. Their electrochemical performance is significantly improved comparing with the commercial sulfur powder and the as-prepared sulfur without honeycomb morphology. There has been no report on using a soft template to prepare honeycomb-like sulfur particles.
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Three-dimensional (3D) TiO2 nanotube arrays grown on Ti mesh were prepared via the anodization process. The diameters of the Ti and TiO 2/Ti wires and the length of the TiO2 nanotubes have linear relationships with the anodization processing time. When the anodization processing time is 600 min, the TiO2/Ti mesh anode materials showed good capacity retention and high specific area capacity, without the need for a current collector or binder, due to their high surface area, high substrate utilization, and large active material loading rate per unit area. At the current density of 50 μA cm-2, TiO2/Ti mesh with 600 …
Mechanically Strong High Performance Layered Polypyrrole Nano Fibre/Graphene Film For Flexible Solid State Supercapacitor, Sha Li, Chen Zhao, Kewei Shu, Caiyun Wang, Zaiping Guo, Gordon G. Wallace, Hua-Kun Liu
Mechanically Strong High Performance Layered Polypyrrole Nano Fibre/Graphene Film For Flexible Solid State Supercapacitor, Sha Li, Chen Zhao, Kewei Shu, Caiyun Wang, Zaiping Guo, Gordon G. Wallace, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Paper like flexible electrode becomes one of the most important research objects recently in request of the fast expanding market of portable electronics. Flexible solid state supercapacitors are shortlisted as one of the most promising energy devices to power electronics with medium to high power density requirements. In this work, we developed a simple but effective way to produce a mechanically strong and electrochemically active RGO/polypyrrole (PPy) fibre paper. A well-bedded microstructure was created with interlaced polypyrrole fibres evenly distributed between the graphene layers. Such microstructure can create enormous amount of pores and therefore provides larger interfaces for charge carrier …
Enhancing The High Rate Capability And Cycling Stability Of Limn2o4 By Coating Of Solid-State Electrolyte Linbo3, Zhijia Zhang, Shulei Chou, Qinfen Gu, Hua-Kun Liu, Huijun Li, Kiyoshi Ozawa, Jiazhao Wang
Enhancing The High Rate Capability And Cycling Stability Of Limn2o4 By Coating Of Solid-State Electrolyte Linbo3, Zhijia Zhang, Shulei Chou, Qinfen Gu, Hua-Kun Liu, Huijun Li, Kiyoshi Ozawa, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
To study the influence of solid state electrolyte coating layers on the performance of cathode materials for lithium-ion batteries in combination with organic liquid electrolyte, LiNbO3 coated Li1.08Mn1.92O4 cathode materials were synthesized by using a facile solid-state reaction method. The 0.06LiNbO3-0.97Li1.08Mn1.92O4 cathode exhibited an initial discharge capacity of 125 mAh g-1, retaining a capacity of 119 mAh g-1, at 25 oC, while at 55 oC, it exhibited an initial discharge capacity of 130 mAh g-1, retaining a capacity of 111 mAh g-1, both at a current density of 0.5 C (where 1 C is 148 mAh g-1). Very good rate …
Fabrication Of Graphene Foam Supported Carbon Nanotube/Polyaniline Hybrids For High-Performance Supercapacitor Applications, Hongxia Yang, Nan Wang, Qun Xu, Zhimin Chen, Yumei Ren, Joselito M. Razal, Jun Chen
Fabrication Of Graphene Foam Supported Carbon Nanotube/Polyaniline Hybrids For High-Performance Supercapacitor Applications, Hongxia Yang, Nan Wang, Qun Xu, Zhimin Chen, Yumei Ren, Joselito M. Razal, Jun Chen
Australian Institute for Innovative Materials - Papers
A large-scale, high-powered energy storage system is crucial for addressing the energy problem. The development of high-performance materials is a key issue in realizing the grid-scale applications of energy-storage devices. In this work, we describe a simple and scalable method for fabricating hybrids (graphenepyrrole/ carbon nanotube-polyaniline (GPCP)) using graphene foam as the supporting template. Graphene-pyrrole (G-Py) aerogels are prepared via a green hydrothermal route from two-dimensional materials such as graphene sheets, while a carbon nanotube/polyaniline (CNT/PANI) composite dispersion is obtained via the in situ polymerization method. The functional nanohybrid materials of GPCP can be assembled by simply dipping the prepared …