Orthodontics and Orthodontology Commons^™

Camouflage Orthodontic Treatment For Adultpatient With Skeletal Class Iii Malocclusion And Bilateral Posterior Cross-Bite, Rouh-Hwai Wang, Hsin-Lan Shen

Taiwanese Journal of Orthodontics

This 23-year-old female presents with skeletal Class III malocclusion, complicated by prominent chin projection, bilateral posterior lingual cross-bite, missing of bilateral maxillary first molars, and severely lingualtilted lower second molars. The treatment modality was conventional edgewise appliance with bilateral lower first premolar extraction. A favorable result of ideal overbite and overjet and correction of bilateral posterior cross-bite were achieved. The patient was satisfied the improvement of function and esthetics after treatment.

Maxillofacial Distraction Osteogenesis, Hong-Po Chang, Tsau-Mau Chou, Yu-Chuan Tseng, Jen-Hao Chen, Han-Jen Hsu, Pao-Hsin Liu

Taiwanese Journal of Orthodontics

Distraction osteogenesis in the maxillofacial skeleton is an increasingly popular alternative to many conventional orthognathic surgical procedures. This review summarizes recent data regarding the biological and biomechanical basis of distraction osteogenesis, its advantages and disadvantages, and special considerations in maxillofacial distraction. Intraoral mandibular distraction osteogenesis, maxillary and midfacial distraction, and alveolar distraction osteogenesis are discussed. This review also discusses sutural expansion/maxillary protraction osteogenesis and orthodontically induced periodontal osteogenesis, which are similar to physeal osteogenesis. In the near future, improved understanding of biomolecular mechanisms that mediate distraction osteogenesis may guide the development of targeted strategies that use molecular mediators, growth factors, …

Solving The Complications Of Treating A Unilateral Submerged And Ankylosed Maxillary Permanent First Molar – A Case Report, Han-Wen Yang, Hsin-Yi Lo, Kwong-Wa Li, Liang-Ru Chen

Taiwanese Journal of Orthodontics

The study reported an adult orthodontic case with a unilateral ankylosed upper permanent first molar. A number of complications occurred, including occlusal plane canting, dental midline deviation and asymmetric molar relationship. The case demonstrated the mechanics used to solve all the complications we met. The case also showed the phenomenon that after extraction of the ankylosed tooth, the bone remodeling mechanism of the bone in situ seemed abnormal and resulted in difficulty of protracting the tooth into the extracted site. All the above reasons, therefore, resulted in prolonged treatment time. In addition, the case also demonstrated the method we used …

Using The Forsus Appliance To Correct Class Ii Mandibular Asymmetry In A Growing Patient: A Case Report, Yun-Fang Chen, Yu-Fang Liao

Taiwanese Journal of Orthodontics

The case report described the orthodontic treatment of a 13-year-old male patient diagnosed as Angle Class II Division 1 subdivision left malocclusion with deep bite and spacing. The chief complaint was protrusive upper front teeth prone to injury. Non-extraction treatment with Forsus appliance and Class II elastics was used to correct the Class II relationship on the left side, and to improve the deviated mandibular dental midline, protrusive front teeth and lips, and lip incompetence. Although there were residual mandibular dental deviation of 0.5 mm and lip incompetence, the patient and his parents were satisfied with the treatment results revealing …

An Investigation Of Surface Characteristics Of Enamel Treated With Infiltrative Resin: A Scanning Electron Microscopy Study, Danielle E. Easterly

Theses and Dissertations

AN INVESTIGATION OF SURFACE CHARACTERISTICS OF ENAMEL TREATED WITH INFILTRATIVE RESIN: A SCANNING ELECTRON MICROSCOPY STUDY

Danielle E. Easterly, Doctorate of Dental Surgery.

A thesis submitted in partial fulfillment of the requirements for the degree of Master of Science in Dentistry at Virginia Commonwealth University.

Virginia Commonwealth University. 2017.

Director: Dr. Eser Tüfekçi

D.D.S., M.S., Ph.D., M.S.H.A.

Objective: To evaluate the microstructural changes of a resin infiltrant (ICON®, DMG America LLC, Englewood, NJ) after six months of simulated toothbrushing.

Materials and Methods: Ten extracted third molars (n=10) were collected. Artificial white spot lesions were created and resin applied. Environmental SEM …

Work-Related Musculoskeletal Disorders Among Dentists And Orthodontists, Natalie R. La Rochelle

Theses and Dissertations

WORK-RELATED MUSCULOSKELETAL DISORDERS AMONG DENTISTS AND ORTHODONTISTS

A thesis submitted in partial fulfillment of the requirements for the degree of

Master of Science in Dentistry at Virginia Commonwealth University.

by

Natalie R. La Rochelle

Thesis Director: Dr. Eser Tüfekçi, D.D.S., M.S., Ph.D., M.S.H.A.

Professor, Department of Orthodontics

Virginia Commonwealth University

Richmond, Virginia

May 2017

The practice of dentistry is physically demanding due to static and dynamic postures sustained daily throughout careers. Previous literature suggests that work-related musculoskeletal disorders (WMSD) are not solely the result of work habits, but also due to the individual, his or her physical makeup, genetics, and …

Comparison Of Intraoral And Extraoral Scanners On The Accuracy Of Digital Model Articulation, Jason L. Porter

Theses and Dissertations

Introduction: Orthodontists increasingly rely on digital models in clinical practice. The ability of modern scanners to articulate digital models must be scientifically evaluated. Methods:Twenty five digital articulated models were produced from four digital scanners in five experimental groups. The resulting inter-arch measurements were compared to the gold standard. An acceptable range of 0.5mm more or less than the gold standard was used for evaluation. Results: iTero® and iTero® Element yielded all acceptable inter-arch measurements. The 3M™ True Definition and Ortho Insight 3D® with Regisil® bite registration produced four of six acceptable inter-arch measurements. The Ortho Insight 3D® with Coprwax ™ …