Other Engineering Commons^™

Fire Protection And Life Safety Evaluation- Hinesville Cboc Va Clinic, Jeff Dew

Fire Protection Engineering: Culminating Experience Project Reports

The Hinesville MOB will be analyzed throughout the course of this report to determine if it meets the prescriptive-based requirements set forth by local and national regulating bodies. Further, a performance-based approach will be taken to assess the buildings ability to sustain life while a safe and timely evacuation occurs. It will be determined that the Hinesville MOB does comply with all regulations set forth for fire and life safety. In some cases its construction and systems may exceed the required minimum standards. It will contain 100% coverage with an automatic sprinkler system, be equipped with adequate emergency notification system, …

Fire And Life Safety Analysis- Cal Poly Recreation Center, Connor Mcgill

Fire Protection Engineering: Culminating Experience Project Reports

The purpose of this fire and life safety analysis is to determine whether Cal Poly’s Recreation Center meets fire safety goals. The primary fire safety goal is to provide building occupants with an environment that is tenable and allows for safe egress in the event of a fire, and reduce the likelihood of any catastrophic fire event. This goal can be achieved by protecting the occupants not intimate with the initial fire development and improving survivability of those occupants intimate with the initial fire development, NFPA 101, 2012. A prescriptive-based design approach and a performance-based design approach are used to …

Horned Lark Management For The Protection Of Lettuce Sprouts, Taylor Wetzel, Eduardo Morales, Kyle Suguitan

Mechanical Engineering

The following document is the Final Project Report. Following the Critical Design Report, the top idea was taken and modified once again to suit the needs of the sponsor. Details regarding the changes are outlined throughout Chapter 3.

The provided background section explains why there is a need for a new device at Tanimura and Antle that will suit the customer's needs better than current methods and existing products. The top ideas picked for the Conceptual Design Review are the presented to reiterate the problems that were depicted in them and why they were not selected as part of the …

Design Analysis Of An Air Force Fuel Cell Maintenance Hangar, Andrew Carmean

Fire Protection Engineering: Culminating Experience Project Reports

A Fuel Cell Maintenance Hangar (FCMH) was constructed in 2013 based on a 2012 design; Figure 1.1.1 is a rendering shown below. This report evaluates the design for life safety, and property protection systems. The facility was designed based on Air Force standard prescriptive methods; the resultant design is compared to minimum prescriptive methods and to as-built drawings. In addition, the property protection design criteria were evaluated by simulating the maximum expected design fire in a hangar bay 1 using Fire Dynamics Simulator (FDS). Section 1 consists of a general overview of the FCMH including descriptions of the facility and …

Fire Protection And Life Safety Analysis- Dell Medical School Academic Building, David Gramlich

Fire Protection Engineering: Culminating Experience Project Reports

This report is on the Dell Medical School Academic Building located in Austin, Texas. The life safety and prescriptive based code requirements are summarized within this report. It also includes conceptual fire protection and fire alarm system design. This report mentions University of Texas System Owner’s Design Guidelines that exceed the required code requirements. This report was developed when the building was in the Design Development stage. Since, code deficiencies have been addressed, and changes have been made to the building during the remainder of the design process, this report does not reflect the actual construction or protection strategies used …

Construction Warehouse, Ben Johnson

Fire Protection Engineering: Culminating Experience Project Reports

The purpose of this report is to provide a comprehensive evaluation of the fire protection and life safety design of a warehouse building that serves a large construction project. The results and conclusions from this evaluation are documented herein and supported by analysis when necessary. The gross floor area per story of the construction warehouse is 39,000 ft2. This building is used as a warehousing facility in support of a large construction project. Rack storage of Group A plastics is permitted in this facility to a height of 20 ft. beneath a 24 ft. ceiling on the main floor. Shelf …

Fire And Life Safety Analysis- Af Child Development Center, Judy Biddle

Fire Protection Engineering: Culminating Experience Project Reports

The purpose of this fire and life safety report is to determine whether The Air Force (AF) Child Development Center (CDC) Standard Design meets fire safety goals based on an increased child-to staff ratio and provide a prescriptive based analysis of the of the existing codes that the building was constructed under. The primary fire safety goal is to provide building occupants with an environment that is reasonably safe from fire. A prescriptive-based design approach and a performance-based design approach are used to evaluate building safety in regards to occupant protection, structural integrity, and systems effectiveness. The prescriptive-based approach is …

Fully Accessible Raised Garden Beds, Ethan Lockwood

Liberal Arts and Engineering Studies

The Ranch, a local nonprofit that is a community gathering location for recreation and education, providing outdoor employment opportunities for area residents with developmental disabilities and a unique experience for volunteers and visitors., was lacking a farming and gardening environment that was fully accessible for all people including those in wheelchairs. This project provided substantial background research for the mission of The Ranch, demonstrated sustainable design, secured material donations, CAD modeled raised beds, and provided meaningful employment during the construction of the raised beds. The project resulted in three different raised bed designs that are all in use by The …

State Of The Art Of Using Virtual Reality Technologies In Built Environment Education., Garrett Keenaghan, Imre Horváth

Conference papers

the application of virtual reality technologies in built environment education (BEE). In addition to an analysis of the current trends and developments in current virtual reality technologies and systems, it also evaluates their educational usability and effectiveness in the mirror of the literature. First, a reasoning model is introduced, which is used as a structuring skeleton of the paper. The context of the analysis is learning experience of BEE students who tend to form individual perspective and expectations. When the experience and perspective of the virtual reality developer differs from that of the user the virtual environment-based learning may result …

Fabrication And Characterization Of Edge-Emitting Semiconductor Lasers, Junyeob Song

Graduate Theses - Physics and Optical Engineering

The semiconductor laser was invented in 1962, and has recently become ubiquitous in modern life. This thesis focuses on the development of a semiconductor laser fabricating process which utilizes semiconductor manufacturing technology in a cleanroom environment including photolithography, etching, deposition, and bonding processes. A photomask for patterning is designed, recipes of photolithography process and etching process are developed with experiments. This work gives how to develop the process of fabrication and determine the parameters for each processes. A series of semiconductor laser devices are then fabricated using the developed process and characterization is performed to assess device performance with industrial …

Calculation And Experimental Verification Of Longitudinal Spatial Hole Burning In High-Power Semiconductor Lasers, Ting Hao

Graduate Theses - Physics and Optical Engineering

Longitudinal spatial hole burning (LSHB) is believed to be one of the limiting factors in scaling the output power of high-power semiconductor lasers. In this work, a self-consistent simulation of LSHB was performed to investigate the non-uniform longitudinal photon density distribution, carrier density distribution, and gain distribution in a high-power semiconductor laser. The calculation is based on a modification to the semiconductor laser rate equations and solved using a finite difference approach, with Newton’s method employed to numerically solve the differential equations. The impact of LSHB on output power was analyzed with different parameters, including injection current, cavity length, and …

Nuts & Bolts, Volume 2, Issue 2, Lance Todd, Julie Thomson, Louis Leviticus

Friends of the Larsen Tractor Museum

Museum Open House is a Success

The Passing of Museum Volunteer Larry Ehlers

Larsen Museum to Auction Twelve Tractors

Details an Estate Planning and Memorial Designation

Computational-Communicative Actions Of Informational Processing, Florentin Smarandache, Stefan Vladutescu

Branch Mathematics and Statistics Faculty and Staff Publications

This study is circumscribed to the Information Science. The zetetic aim of research is double: a) to define the concept of action of informational processing and b) to design a taxonomy of actions of informational processing. First, the investigation trays to demonstrate that the computational actions of informational processing or the informational actions are computational-investigative configurations for structuring information: clusters of highly-aggregated operations which are carried out in a unitary manner operate convergently and behave like a unique computational device. From a methodological point of view, they are comprised within the category of analytical instruments for the informational processing of …

Modeling Preventive Maintenance In Complex Systems, Jessica Rivas

Open Access Theses

This thesis presents an explicit consideration of the impacts of modeling decisions on the resulting maintenance planning. Incomplete data is common in maintenance planning, but is rarely considered explicitly. Robust optimization aims to minimize the impact of uncertainty--here, in contrast, I show how its impact can be explicitly quantified. Doing so allows decision makers to determine whether it is worthwhile to invest in reducing uncertainty about the system or the effect of maintenance. The thesis consists of two parts. Part I uses a case study to show how incomplete data arises and how the data can be used to derive …

A Change Management Approach To Enhance Facility Maintenance Programs, Stanton P. Brown

Theses and Dissertations

A recent study assigned a grade of D+ on the nation's public infrastructure. Because of this poor asset condition, many organizations tend to respond to maintenance in a reactive mode; however, relying on corrective maintenance leads to increased maintenance costs due to unplanned downtime, increased labor costs, and inefficient use of personnel. To address this situation, asset management (AM) principles should be employed to transition organizations towards a proactive maintenance program. Unfortunately, it has been shown that two-thirds of the organizations failed to implement general change efforts. Therefore, an organizational change management framework should be followed to implement a change …

Assessing The Effectiveness Of A Problem-Based Computer Modelling Module From The Student's Perspective, Garrett Keane, Brian Bowe

Conference papers

The Computer Modelling module delivered to the third year Level 8 Mechanical Engineering students in the Technological University Dublin is marked completely by continual assessment. It was developed using a problem based approach in that the theory of Computer Modelling methods is first explained but is then illustrated by demonstrating its application to the solution of real life problems. It is delivered in a traditional manner for the first six weeks in that the underlying principles and techniques of the finite difference method are covered in lectures and practical assignments are completed in the weekly computer laboratory classes. A problem …

Orangeburg Assembly Hall Of Jehovah's Witnesses- Fire Protection And Life Safety Design Analysis, Justin B. Biller

Fire Protection Engineering: Culminating Experience Project Reports

In partial fulfillment of the requirements for the Degree of Masters of Science in Fire Protection Engineering, a prescriptive and performance-based engineering analysis was performed on the Orangeburg Assembly Hall of Jehovah’s Witnesses. The building was recently constructed and completed in 2013 in Orangeburg, South Carolina to serve as a center for education of Jehovah’s Witnesses on Biblical principles for daily life. More than 300 congregations throughout Georgia and the Carolinas will use the Assembly Hall for their semi-annual assemblies and conventions, with an estimated annual attendance of 190,000 per year. Prescriptive analyses were conducted based primarily upon the provisions …

Fuzz Pedal Design Project, Kyle Schaefer

Biomedical Engineering

The purpose of this project was to design and build a high quality, yet affordable, analog “fuzz” guitar pedal kit to be sold to other members of Cal Poly’s Audio Engineering Society. The Audio Engineering Society (AES) has hosted pedal-building projects in the past, but my project partner Michael Twardochleb first had the idea to build an original kit to be officially affiliated with the club. Michael had built other pedals of his own in the past, making him an excellent partner to have for this project. Our design was based on the classic Vox Tonebender’s circuit, which was in …

Fire Protection Life Safety Analysis- Bachelor Enlisted Quarters, Kyle C. Leadon

Fire Protection Engineering: Culminating Experience Project Reports

This Bachelor Enlisted Quarters (BEQ) shall be constructed, arranged, equipped, maintained, and operated in accordance with this report and applicable criteria to ensure a minimum level of life safety and property protection is provided from actual and potential fire hazards. The goal is to ensure the occupants are provided with an environment that is reasonably safe from fire. We accomplish this goal by protecting occupants not intimate with the initial fire development, and by improving the survivability of occupants intimate with the initial fire development. The protection described in this report takes on many forms, from active protection, such as …

Ireland's Residential Rental Market Needs A Massive Shake-Up, Lorcan Sirr, Tom Dunne

Media

No abstract provided.

We Need A Coherent Policy To Guide Housing In Ireland, Lorcan Sirr

Media

No abstract provided.

Private Rented Sector In Urgent Need Of Reform, Lorcan Sirr

Media

No abstract provided.

Sac Drone History, John Dale

ERAU Prescott Aviation History Program

Learn about the previously classified Strategic Air Command drone reconnaissance program covering targets in China, N. Korea, & N. Vietnam, from the pilot who was in charge. Specially modified C-130s launched the drones that were then recovered in mid-air by helicopters. They went where manned aircraft could not and some wouldn’t make it back! This program contributed to the amazing UAVs of today.

Method And System For Optimal Coordination Control And Soft Repair Of Multiple Rooftop Heating And Cooling Units, Haorong Li

Durham School of Architectural Engineering and Construction: Faculty Publications

Techniques are described that may be implemented in an adaptive control device to regulate multiple zone environmental units based upon multiple temperature values and multiple airflow values, where each temperature value and each airflow value is related to the temperature and the airflow in a specific zone. In an implementation, the input interface of the adaptive control device is configured to receive multiple temperature values and multiple air flow values from multiple zone sensors. The adaptive control device may calculate multiple operational values based on the multiple temperature values and the multiple air flow values. An operational value indicates a …

An Assessment Of The College Of Technology, Architecture And Applied Engineering’S Master Of Technology Management Degree Program, Quality Systems Specialization, At Bowling Green State University, Alan Powers

Master of Technology Management Plan II Graduate Projects

The purpose of this project is to give a background and assessment of the quality specialization of the Master’s degree presently being awarded at Bowling Green State University’s College of Technology, Architecture, and Applied Engineering compared to other degrees of a similar type. The program now awarding the degree is described. The literature review discusses topics and ideas pertinent to the project and is necessary to better understand the research and assessment of the degree. The methodology and procedure section identifies the course of investigation and defines what form the gathered data will take. The Results chapter presents the findings …

Perceptions Of Manufacturing Management Knowledge And The Four Pillars Topical Track: Manufacturing, Mark Doggett, Muhammad Jahan

SEAS Faculty Publications

In June 2011, a group of manufacturing educators in cooperation with the Society of Manufacturing Engineers (SME) developed Curriculum 2015, a four-year strategic plan to reverse negative trends in manufacturing education and improve manufacturing competitiveness. Within this effort, the Four Pillars of Manufacturing Engineering were formally introduced and supported by the Society of Manufacturing Engineers (SME), the Association of Technology, Management, and Applied Engineering, (ATMAE), and the Accreditation Board for Engineering and Technology (ABET). The Four Pillars consist of foundational areas that represent the SME Certified Manufacturing Engineer Body of Knowledge. It embodies the fundamental knowledge practiced by manufacturing professionals …

A Review Of Process And Product Systems In Construction, Charles Anthony Mitchell

Reports

This paper was produced as part of the coursework associated with a Masters in Quantity Surveying (Mechanical and Electrical) undertaken by the Author. The aim of the research was to study and review 1) processes and sub-processes in the pre-construction phase, 2) risk analysis in the project and 3) the use of off-site construction in relation to an iconic structure of the author’s choice. In the absence of information the author was permitted to make assumptions about the processes involved as long as these were qualified within the text.

The author chose the Aviva stadium, Dublin 4 as the iconic …

How Robotics Programs Influence Young Women’S Career Choices: A Grounded Theory Model, Cecilia D. Craig

2010-2016 Archived Posters

Women in college, alumnae of a well-known high school robotics program, shared how it influenced their career choices and who they have become in this qualitative study. A general system theory model was developed using grounded theory practices, after conducting online focus groups and interviews.

Stock Aggregation Model And Virtual Archetype For Large Scale Retrofit Modelling Of Local Authority Housing In Ireland, James Pittam, Paul D. O’Sullivan, Garrett O’Sullivan

Conference Papers

Developing representative archetypes using a bottom up approach for stock modelling is an excellent tool for evaluating the overall performance of the building stock; however it requires detailed analysis of the various building types. Currently there is no detailed housing data base for Local Authority housing in Cork City, Ireland that catalogues the housing stocks geometric properties and thermal characteristics for each typology. This study details a methodology to catalogue the LAH stock and build a detailed housing data base. The GIS web based mapping application Google Street View is used to identify 20 house typologies across 36 LAH developments; …

What Role Does Mathematical Preparedness Play For Engineering Students Who Transfer From And Ordinary Degree Into An Honours Degree?, Michael Carr, Marisa Llorens, Susan O'Shaughnessy, Anne Marie Mccarrick, Domhnall Sheridan

Conference papers

Students who have not achieved a high level of mathematics at secondary school but have a pass in ordinary level mathematics have the option of entering onto a 3-year Ordinary degree (Level 7). Upon successful completion of this award students may apply to progress to the third year of the Honours degree. Up until relatively recently an upper merit (60%) was the minimum required to make this transition. In recent years this requirement has been reduced with many students with lower marks being offered the possibility of transferring.

Relatively little work has been done on the transition from an Ordinary …