Other Operations Research, Systems Engineering and Industrial Engineering Commons^™

Modeling The Influence Of Internal Factors On Vehicular Mobility Performance, Aziz Mdimi

Tanzania Journal of Engineering and Technology (TJET)

Traffic mobility is significantly influenced by road conditions and the internal factors governing vehicular performance. Internal factors play a crucial role in vehicular mobility, influencing vehicles operate and performance. While existing vehicular mobility models primarily address external factors, external factors such as governor, engine, gear train and differential unit remain underexplored. This study formulates a comprehensive model to address this gap, focusing on the internal components that affect vehicular mobility. The proposed model employs both analytical and numerical methods to derive transfer functions for these subsystems using Matrix Laboratory (MATLAB), aiming to capture the dynamic behavior of vehicles under various …

Necessity Of Education For Efficient And Sustainable Production And Consumption Of Energy In Tanzania, George Kahangwa

Tanzania Journal of Engineering and Technology (TJET)

This paper reports the findings of a study that was conducted in Tanzania to grasp how the policies, plans and curricula at different levels of education accommodate knowledge gathered on energy to support the fostering of energy education. The study interrogated what necessitates the inclusion of energy education into the curricula in Tanzania. Subscribing to a qualitative approach, the study employed a desk research method to review curricula and other documents guiding secondary and university level education in the country. The study found out that heightening people’s consumption of energy for domestic and industrial purposes constituted the main issue that …

Assessing The Importance Of Air-Decking Blasting In Controlling Bigv At An Open Pit Gold Mine In Tanzania Using Ann Model, Karim R. Baruti

Tanzania Journal of Engineering and Technology (TJET)

Air-decking blasting technique is used to control blast induced ground vibration (BIGV) in several mines including open-pit gold mines located in Tanzania. While the importance of air-deck to control BIGV is practically evident, theoretical models such as BIGV prediction models cannot be used to assess the importance of air-decking. The main objective of this study was to assess the importance of the air-decking blasting technique to control BIGV using the artificial neural network (ANN)Model. To achieve this objective, ANNs were modeled and trained to learn the pattern of data using Multilayer Perception with Back Propagation to predict BIGV. The main …

How Ai And Digitalization Can Help To Improve Managing Projects In Lean Manufacturing & Supply Chain Environment, Abhijeet Hange

Harrisburg University Dissertations and Theses

This research examines how digitalization and machine learning (ML) revolutionize project management in supply chain and lean manufacturing settings. To improve the efficiency and caliber of their operational procedures, Acuity Brands, Amazon, Walmart, Apple, and other medium-sized businesses—which are at the center of today's competitive markets—are resorting to automation and digitalization. With an emphasis on the fusion of digital and artificial intelligence (AI), the paper explores how successful transformation initiatives are essential to the automation and digitization of manufacturing and distribution hubs. The study uses quantitative methods approach to evaluate the benefits and drawbacks of these technology integrations by integrating …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

Comparison Of Meteorological Drought Indices In Tanzania Using The Meteorological Drought Monitoring Software Package, Paul Ts Limbu

Tanzania Journal of Engineering and Technology (TJET)

Low precipitation, substantial evaporation, and an unequal distribution of precipitation throughout the area are the characteristics of drought, a climatic abnormality. This study used the Meteorological Drought Monitoring (MDM) software and monthly rainfall data from the Tanzania Meteorological Authority (TMA) to examine and compare the Deciles Index (DI), Standardised Precipitation Index (SPI), Percent of Normal Index (PNI), Rainfall Anomaly Index (RAI), Z-Score Index (ZSI), China-Z Index (CZI), and Modified China-Z Index (MCZI) for drought monitoring in Tanzania from 1988 to 2017. It was found that ZSI represented the dry years better than other indices, followed by DI, RAI, PNI, SPI, …

Accelerating Manufacturing Decisions Using Bayesian Optimization: An Optimization And Prediction Perspective, Taofeeq Olajire

Graduate Theses, Dissertations, and Problem Reports (ETD)

Manufacturing is a promising technique for producing complex and custom-made parts with a high degree of precision. It can also provide us with desired materials and products with specified properties. To achieve that, it is crucial to find out the optimum point of process parameters that have a significant impact on the properties and quality of the final product. Unfortunately, optimizing these parameters can be challenging due to the complex and nonlinear nature of the underlying process, which becomes more complicated when there are conflicting objectives, sometimes with multiple goals. Furthermore, experiments are usually costly, time-consuming, and require expensive materials, …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim

Electronic Theses, Projects, and Dissertations

Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Inventory Locating With Quuppa: The Design And Development Of A Real-Time Process Monitoring Web Application Solution, Dylan C. Moreland, Trevor J. Howell, John W. Takiff, Patrick S. Dillon, Theo E. Fritz, William K. Mcintyre

Industrial and Manufacturing Engineering

Viasat, Inc. requires precise inventory tracking at their production facility in San Diego, CA. Viasat has installed the Quuppa indoor real-time locating system (RTLS), which it uses to track the real-time position of high-value work-in-process items. In its current state, the system only displays in-the-moment location information, with no available functionality for storing historical data for review, analysis, or visualization. In addition, the data displayed is noisy and prone to significant random error. This paper provides an overview of RTLS methods and technologies, assesses alternative solutions to Viasat’s issue, demonstrates our RTLS integrated web app solution, analyzes its impact, and …

Solar Photovoltaic Performance Monitoring: A Bibliometric Review, Research Gaps And Opportunities, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Electrical power generation has been revolutionized by growing demand and use of Renewable Energy (RE) sources such as Solar Photovoltaic (SPV) as the main electricity source in modern times. The main objective of this bibliometric analysis is to understand the scope of the literature available for SPV performance characterization. This detailed reviewed was performed on the documents related to SPV research considering all the subject categories from Scopus and Web of Science (WoS) databases. The patterns for the particular set of keywords were broke down with the recuperated outcomes from Scopus database in the language, publication type, year of publication, …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Material Interactions And Self-Assembly In Inkjet Printing, Karam Nashwan Al-Milaji

Theses and Dissertations

Inkjet printing has attracted much attention in recent years as a versatile manufacturing tool, suitable for printing functional materials. This facile, low-cost printing technique with high throughput and accuracy is considered promising for a wide range of applications including but not limited to optical and electronic devices, sensors, solar cells, biochips, and displays. The performance of such functional devices is significantly influenced by the deposit morphology and printing resolution. Therefore, fabrication functional devices with precise footprints by inkjet printing requires deep understanding of ink properties, material interactions, and material self-assembly.

In conventional inkjet printing process, where sessile droplets are directly …

Modular Crates – A Holistic Design Approach For Optimizing Cube Size In Industrial Packaging, Marshal Louie, Kumar B

Journal of Applied Packaging Research

Global market is a field where all industries strive to provide personalized product for every customer demand in order to compete with their competitors in the business battlefield. Product personalization varies with customer to customer which increases the product variety. When the product size variability is vast, producing packages for every individual product is not only difficult but also increases the design time, production time, total manufacturing cost and inventory cost. For the present scenario, Industrial packages does not opt customizability for variable product sizes. Customized package for personalized product is achievable only by redesigning the existing distribution package with …

Answering Food Insecurity: Serving The Community With Food And Knowledge Using Technology, Courtney Simpson

Purdue Journal of Service-Learning and International Engagement

The courses of Tech120, CGT110, and ENGT 180/181 and Red Gold at Purdue collaborated to design a robot that would plant and water a garden for a local community charter school. The students centered the project on the users’ needs for fresh food, nutrition education, and early exposure to STEM for children. The school, Anderson Preparatory Academy (APA), is comprised of many children who come from low-income families and are in the free or reduced lunch program. Inspired from “Farm Bot,” a similar system that allows for almost hands-free gardening, the “Boiler Bot” is designed to be scalable so children …

Chocolate Bar Wrapping Machine, Austin M. Hoff, Daniel R. Trepke, Caleb B. Krichbuam

Williams Honors College, Honors Research Projects

Gilbert Chocolates has proposed to manufacture a machine to wrap chocolate bars. This machine is intended to replace two people wrapping the chocolate bars by hand, which is a time consuming method. This is especially apparent between October and January when the workers are working long hours in preparation for the Christmas rush of customers. Currently wrapping a bar takes about a minute and Gilbert Chocolates wants this time reduced down to 20-30 seconds. The budget for this project is set at $1000, and is being funded by the company. This machine needs to fit in a cubic foot of …

Mri Upgrades At Radiology Associates, Patrick Cheung, Charlene Donlon

Industrial and Manufacturing Engineering

Problem Statement: The MRI machines at Radiology Associates are limiting the company’s ability to expand and compete within the local market. After discussing with technicians and managers at Radiology Associates, we decided to focus on hardware and software upgrades for the MRI machines. With 2 of the 3 locations purchasing new machines in the near future, our focus was on upgrades at the Santa Maria facility. The two machines at this location needed hardware and/or software upgrades to remain on par competitively both within the company and with local scanning options. Flexible coils are beneficial in terms of size, weight, …

Process Improvement By Lean Thinking In Trucking Industry, Abhiram Reddy Ramasahayam

All Graduate Theses, Dissertations, and Other Capstone Projects

Manufacturing industries with complex production systems are struggling with designing optimal process to increase throughput. Companies will require high amount of labor and process improvement resources to sustain growth and delivery quality products to its customers. A chain of value added activities when designed and deployed with help of lean based methodologies can create high efficiency process. In this paper we have studies and implemented value added process based on the lean manufacturing methodologies which was adapted on the shop floor.

In many traditional truck body production industries have facing many problems like low production rate, big lead times, material …

Underwater Rope Fatigue Testing Machine, Napoleon Nino, Andrew Pimentel

Mechanical Engineering

The design and fabrication of an underwater rope fatigue testing machine meant to simulate the effects of an oceanic environment and the effects on rope.

Design And Research Of Vlcc Vessel Virtual Marine Engine Room, Chuang Zhao

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Testing The Fuel Efficiency Of Tractors With Continuously Variable And Standard Geared Transmissions, Christopher N. Howard, Michael F. Kocher, Roger M. Hoy, Erin E. Blankenship

Department of Agricultural and Biological Systems Engineering: Faculty Publications

A John Deere 8295R IVT tractor with a continuously variable transmission (CVT) and a John Deere 8295R PowerShift (PST) tractor with a standard geared transmission (GT) were tested for fuel consumption at three different travel speeds with six different load levels applied per speed. The JD 8295R PST tractor was tested both at full throttle (FT) and shifted up two gears and throttled back (SUTB) to achieve the same travel speed as at full throttle. For each travel speed with each transmission mode, fuel consumption was determined to be linearly related to drawbar power. Linear regression analyses were performed, and …

Development And Validation Of A Model For Granular Material Volume Measurements, Pourya Fasounaki

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Keeping inventory record of packed grains in silos poses challenges since the bulk material’s different segments do not discharge uniformly, leading to formation of random peaks and valleys on the surface. To facilitate obtaining accurate volume measurement of the grains by taking into account this non-linear behavior on the surface, laser or plumb-bob level-sensing devices are employed at different part of the surface to probe the level of material under those regions.

The main goals of this research is to study the behavior of granular material in silo while discharging downward and by doing so, differentiate certain flow patterns formed …

Laser Clean Room Re-Design: A Manufacturing Facility Re-Layout, Jennifer J. Siu

Industrial and Manufacturing Engineering

Alcon’s Laser Clean Room fosters inefficient production practices, is outdated for its current process, and lacking in clear process/product flow. A facility re-design is applied to bring order, efficiency, and optimize flow in the laser production lines.

Deliverables include a new layout that decreases product travel distances and increases productivity as well as an implementation plan and cost/savings analysis. Major design decisions include downsizing the clean room, sorting to find waste and establishing clear process/product flows. The design was implemented within three weeks and results yield 29% reduction of product travel distance, 10.4 hrs/day saved from eliminated gowning time and …

Design For Manufacturing Of Sports Equipment, Cedrick Bit, Christopher L. Head

Industrial and Manufacturing Engineering

The purpose of this project was to validate industrial designs for a product in its conceptual stage and suggest/implement design changes that suit the contracting company’s needs while assuring the product maintains its basic functional requirements. Techniques and methods used to validate the design include 3‐D solid modeling, physical product application using rapid prototyping to produce the product. Methods of design for manufacturing were analyzed in the design. Processes used in the validation and verification of the design include solid modeling design, methods of measurements, fixture design and manufacturing processes. Full design specifications and solid model files were finalized and …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …