Industrial Engineering Commons^™

Participatory Evaluation And Improvement Of Cassava Processing Machines For The Eastern Zone Of Tanzania, V Silayo

Tanzania Journal of Engineering and Technology (TJET)

Cassava processing machines previously introduced in Tanzania were chippers and graters of the International Institute Of Tropical Agriculture (IITA) design. Popularization of such machmes in Tanzania required thorough participatory testing with stakeholders. When tested with farmers in Muheza and Kibaha districts average throughputs were 11-18 kg/h, 752 kg/h and 270 kg/hfor the manual chipper, engine-powered chipper and the engine-powered grater, respectively. Despite their low throughputs the manual chipper and the grater were Veo difficult to operate, and therefore demanded improvement. Improvement on these machines included modifications on the design for increased throughput, ease of operation and safety. The improved machines …

Aeration Efficiency Of A Three-Phase Fluidized Bed Bioreactor During Food Industry Wastewater Treatment, S Manyele

Tanzania Journal of Engineering and Technology (TJET)

The implementation Of a three-phase fluidized bed bioreaclor (TPFBB) in food- processing wastewater (FPW'W) treatment is reported. This study includes the modification Of the air distributor (plate design and gas-liquid mixing) for the bioreactor and resting of its aeration efficiency under different liquids. The aeration efficiency for wastewater samples collected from a soft drink processing industry and tannin processing industry (TANWA T) and tap water were compared. The aeration efficiency parameters studied include bed expansion, air holdup. volumetric oxygen mass transfer coefficient, and alpha factors. The variation of these parameters With air flow rates were studied at different liquid heights, …

Usefulness Of Technology Life Cycle In Tanzania: The Case Of The Ipl Developed Technologies, Abdallah Chungu

Tanzania Journal of Engineering and Technology (TJET)

This study sought to identify the adoption rate of technologv innovations developed by the Institute Of Production Innovation (IPI) at the University Of Dar-es-Salaam since 1984 to 1997 using a sigmoid shaped curve (S-shaped curves) to predict the life cycles of the respective technologies. Depending on the stimuli imparted to the specific technology, some of such technologies for instance, cinva ram and block making machines with hollow/spacer/louver exhibited longer life period as indicated by a series Of infer-connected S-curves. Other technologies including but nor limited to sunflower oil processing kit-winnowers, scorcher with one stove, seed roller, standard wheelbarrow, and manual …

Comparative Study Of The Dynamics Of Circulating Fluidized Bed Riser And Downer Of Equal Diameters, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The microscopic flow dynamics of the 100-mm internal diameter riser/downer circulating fluidized bed (CFB) unit were monitored using a solids concentration fiber optic probe. The comparison was conducted by comparing radial profiles Of the dynamic parameters derived from time-series analysis techniques (statistical and chaos analyses). The solids concentration signals used were recorded under similar operating conditions (gas velocity of 8.0 m/s and solids flux of 100 kg/m2s). Similar axial elevations were compared (entrance and fully developed sections of die reactors). A1 each loca!ion, the signals were sampled a! afrequency of 970 Hz for duration of 30 seconds. It was observed …

Intelligent Simulation-Based Lot Scheduling Of Photolithography Toolsets In A Wafer Fabrication Facility, Amr Arisha, Paul Young

Conference papers

Scheduling of a semiconductor manufacturing facility is one of the most complex tasks encountered. Confronted with a high technology product market, semiconductor manufacturing is increasingly more dynamic and competitive in the introduction of new products in shorter time intervals. Photolithography, being one of the processes repeated often, is a fabrication bottleneck. Lot scheduling within photolithography is a challenging activity where substantial improvements in factory performance can be made. The proposed scheduling methodology integrates two common approaches, simulation and artificial intelligence. Using detailed simulation modeling within a structured modeling method, a comprehensive model to characterize the photolithography process was developed. An …

Comparison Of Sampling Methods For Flatness Evaluation Using Cmm, Ashish Singhal

All-Inclusive List of Electronic Theses and Dissertations

Efficient part feature verification using Coordinate Measuring Machine (CMM) requires efficient sample point selection as well as accurate zone fitting. This work deals with flatness tolerance evaluation and the Least- Square (LS) technique is used to compute tolerance zone. In regard to the sampling strategy there are several methods commonly employed in Coordinate Measuring Machine inspection literature. The appropriate method is selected according to the accuracy requirement, the geometry features of the work piece, and the condition of the machine producing the work piece. This research focuses on the five sampling methods: Hammersley sequence sampling, Halton-Zaremba sequence sampling, Random sampling, …

Using Simulation Techniques To Evaluate Group Technology Heuristics: A Recommended Methodology For Comparison And Optimization, Ashley Nolen Akerman

Masters Theses

Machine cell formation is an important issue in industrial and manufacturing engineering. Properly assigned machine cells can improve manufacturing system efficiencies and decrease unnecessary material movement. To address the need for proper cell formation techniques a myriad of heuristics have been created that attempt to optimize the grouping of machines. Further, much industrial engineering research has been conducted on the application of simulation technology to manufacturing system evaluation.

The purpose of this thesis is to investigate the combination of traditional machine grouping heuristics with simulation technology and to create a generalized meta-model based upon this evaluation. This investigation analyzes the …

Integration Of Lean Manufacturing And Value Engineering Techniques To Improve The Internal Distribution System In A Manufacturing Company, Sripadjaraj Prahladaraj

Masters Theses and Doctoral Dissertations

The XYZ Corporation is located in Lafayette, Georgia. The company produces cooking ranges for the North American market. It has 1500 employees with a daily production capacity of 1000 to 1500 cooking ranges. The company is implementing lean manufacturing techniques to improve their performance. One of their projects is to develop a distribution system, which will help in streamlining the internal distribution of Very High Pressure (VHP) adhesive tapes. The aim of this research is to develop a lean distribution system by applying techniques of lean manufacturing systems. To understand the existing process of distribution, a flow diagram was created. …

Lead-Free Solder Joint Reliability – State Of The Art And Perspectives, Jianbiao Pan, Jyhwen Wang, David M. Shaddock

Industrial and Manufacturing Engineering

There is an increasing demand in replacing tin-lead (Sn/Pb) solders with lead-free solders in the electronics industry due to health and environmental concern. The European Union recently passed a law to ban the use of lead in electronic products. The ban will go into effect in July of 2006. The Japanese electronics industry has worked to eliminate lead from consumer electronic products for several years. Although currently there are no specific regulations banning lead in electronics devices in the United States, many companies and consortiums are working on lead-free solder initiatives including Intel, Motorola, Agilent Technologies, General Electric, Boeing, NEMI …

Evaluation Of Bus And Truck Automation Operations Concepts, H.-S. Jacob Tsao, Lan Zhang, Lin Lin, Deepa Batni

Faculty Publications

Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has funded with approximately $125K a research project entitled “Evaluation of Bus and Truck Automation Scenarios” jointly proposed by Jan Botha (Principal Investigator) of Department of Civil and Environmental Engineering and Jacob Tsao (Co-PI) of Department of Industrial and Systems Engineering at San Jose State University. This report summarizes the major findings of the research conducted by Professor Tsao and his assistants with approximately $44K out of …

A Case Study Of Teaching A Quantitative Course Using Archived Streaming Video, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

This case study highlights some of the issues and difficulties experienced in teaching a quantitative course using three methods of delivery: in-class to an audience of students, television broadcast over a satellite system to distance students, and archived streaming video accessible by students. The discussion is applicable to administrators and faculty exploring the option of teaching a course using multiple delivery approaches.

Lean Energy Analysis: Identifying, Discovering And Tracking Energy Savings Potential, J. Kelly Kissock, John Seryak

Mechanical and Aerospace Engineering Faculty Publications

Energy in manufacturing facilities is used for direct production of goods, space conditioning, and general facility support such as lighting. This paper presents a methodology, called lean energy analysis, LEA, for graphically and statistically analyzing plant energy use in terms of these major end uses.

The LEA methodology uses as few as 60 easily obtainable data points. Multivariable change-point models of electricity and natural gas use as functions of outdoor air temperature and production data are developed. The statistical models are used to subdivide plant energy use into facility, space-conditioning and production-related components.

These breakdowns suggest the savings potential from …

Work Flow Policy And Within-Worker And Between-Workers Variability In Performance, Kenneth Howard Doerr, Tali Freed, Terence R. Mitchell, Chester A. Schriesheim, Xiaohua Zhou

Industrial and Manufacturing Engineering

Work flow policies are shown to induce a change in average between-workers variability (worker heterogeneity) and within-worker variability in performance times. In a laboratory experiment, the authors measured the levels of worker heterogeneity and within-worker variability under an individual performance condition, a work sharing condition, and a fixed assignment condition. The work sharing policy increased the levels of worker heterogeneity and worker variability, whereas the fixed assignment policy decreased them. These effects, along with work flow policy main effects on mean performance times and variability are examined. This article represents an initial step in understanding effects that may be important …

A Template-Based Conceptual Modeling Infrastructure For Simulation Of Physical Security Systems, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Although simulation is one of the most innovative and cost-effective tools for modeling and analyzing a system, simulation studies often fail to provide any useful results. One reason is attributed to the fact that model formulation depends on the skills of the analyst. This paper describes a research to develop a conceptual modeling infrastructure to assist a simulation analyst in specifying components for studying physical security systems. The modeling framework has been programmed as an internet-based web application. Using the application, the successful development and implementation of a physical security simulation model will be aided by a defined scientific methodology …

Investigating Graphical User Interface Usability On Task Sequence And Display Structure Dependencies, Tirthankar Sengupta

Dissertations

Designing Graphical User Interfaces (GUI) requires the consideration of task sequence requirements (sequence of operations arising from task structures and application constraints) and display structure (layout of the elements of the interface) relationships. The basic purpose was to understand the usability differences of the interfaces through efficiency, motor performance, and search performance.

Thirty-two subjects performed experiments in four groups. The experiments differed in display structure and compatibility of task sequences. Subject mouse actions, mouse coordinates and eye positions were recorded. The derived measures, click efficiency, mouse traversal and eye visits to different areas of interest (namely the tool, object, and …

Wire Bonding Challenges In Optoelectronics Packaging, Jianbiao Pan, Patrice Fraud

Industrial and Manufacturing Engineering

Wire bonding has been used in integrated circuit (IC) packaging for many years. However, there are many challenges in wire bonding for optoelectronics packaging. These challenges include bonding on sensitive devices, bonding over cavity, bonding over cantilevel leads and bonding temperature limitations. The optoelectronics package design brings another challenge, which requires wire bonding to have deep access capability. In this paper, the wire bonding technologies are reviewed and ball bonding and wedge bonding are compared. The variables that affect the wire bonding process are then discussed. Finally, the challenges of wire bonding in optoelectronics packaging are presented in detail.

Effect Of Chromium-Gold And Titanium-Titanium Nitride-Platinum-Gold Metallization On Wire/Ribbon Bondability, Jianbiao Pan, Robert M. Pafchek, Frank F. Judd, Jason Baxter

Industrial and Manufacturing Engineering

Gold metallization on wafer substrates for wire/ribbon bond applications require good bond strength to the substrate without weakening the wire/ribbon. This paper compares the ribbon bondability of Cr/Au and Ti/TiN/Pt/Au metallization systems. Both chromium and titanium are used to promote adhesion between substrates and sputtered gold films. Both can diffuse the gold surface after annealing and degrade the wire/ribbon bondability. Restoring bondability by ceric ammonium nitrate (CAN) etch was investigated. Experiments were conducted to investigate the effect of Cr/Au and Ti/TiN/Pt/Au, annealing, and CAN etch processes on 25.4 times; 254 μm (1 × 10 mil) ribbon bonding. All bonds were …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Importance Of Structural Fire Protection In Reinforced Concrete Buildings: A Case Study Of Ex-Nasaco Building In Dar Es Salaam, I Rubaratuka

Tanzania Journal of Engineering and Technology (TJET)

Reinforced concrete is concrete that is internally reinforced with steel bars or mesh. This gives rhe malerial the compressive strength of concrete along wilh the tensile strength Of steel. Reinforced concrete does not perform well under fire conditions as it spalls and loses strength. Heating Causes a failure Of the bond between concrele and sleels bars and this results in reduction of strength of concrele. Strength of concrete decreases With increase in temperature and increase With time. In order to provide fire resistance to structural components/elements in buildings, it is important Io consider the type of aggregates to be used. …

Introduction Of Seismic Resistance Features In The Construction Of Buildings In Tanzania, I Rubaratuka

Tanzania Journal of Engineering and Technology (TJET)

Available dara indicates that a greater part of Tanzania lies within a seismic region. to date most Of the buildings in the country have been designed and constructed without considering seismic loads. In addition no design codes have been developed to guide the seismic design for buildings and other related structures in Tanzania. This paper outlines the basic design concepts, which are useful during the design of seismic resistant buildings before the seismic design code is developed and adopted in Tanzania.

Derivation And Analysis Of Maximum And Conditional Work Of An Electromagnet In Relays With Small Gaps And Constant Armature Load, Dominic Chambega

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

How To Increase The Ability Of A Student To Learn, Srinivas R. Chakravarthy

Industrial & Manufacturing Engineering Presentations And Conference Materials

An instructor is always challenged when covering the materials in a course (according to the syllabus) and at the same time making sure that all students have the opportunity to learn and understand the materials presented in the classroom. In this paper we will present some ideas and tools that enable one to try to achieve a balance. These are based on the author’s experience and perspective in teaching deterministic and stochastic operations research courses.

Case Studies In Disassembly Process Planning, Riteshkumar Dhimmar

Theses

The rapid advancement in technology started in last century and still continuing resulted in decreased life cycle of electronic products. It also resulted in increased product disposal rate and filling land fill space faster causing shortage of such space and consequently creates major environmental problems. So, since couple of decade environmental concern has focused on production process and environmental regulations imposed by government has watched industrial pollution. With government regulations to control environmental problems; consumers are also aware of adverse effects of product disposal forcing manufacturer to become more responsible for safe product disposal and recycling of used product.

A …

Supply Chain Risk Analysis, Venkata R. Kallepalli

Theses

A new decision support system is proposed and developed that will help sustaining business in a high-risk business environment. The system is developed as a web application to better integrate the supply chain entities and to provide a common platform for performing risk analysis in a supply chain. The system performs a risk analysis and calculates risk factor with each activity in the supply considering its interrelationship with other activities. Bayesian networks along with fault tree structures are embedded in the system and logical rules are used to perform a qualitative fault tree analysis, as the data required to calculate …

Supply Chain Risk Mitigation, Roshan R. Pai

Theses

In recent years, especially post 9/11, there has been an increasing awareness for securing business supply chains against probable disruptions. With globalization and lean inventories, the efficiency of supply chain has greatly enhanced over the years, but at the expense of new vulnerabilities. Supply chain vulnerabilities have resulted in disruptions to the economic stability and security. As a result, risk analysis and mitigation has now grown to become one of the key links to business stabilization. To ensure business continuity, it is necessary to identify key assets (physical and operational) within the supply chain and secure them against probable threats. …

Simulation Analysis Of Anti-Rollover Mechanism For Vehicles, Mohib L. Raid

Theses

Rollover accidents are considered the most significant safety problems for all classes of light vehicles, especially pickups, Sport Utility Vehicles (SUV), Light Truck Vehicle (LTV) and vans. The main objective of the research is the design of a new mechanism able to keep the vehicle stable under various road conditions and high speeds, to prevent the vehicle from rolling over and to maintain the stability for the vehicle by creating an anti-rolling torque on the vehicle body capable of turning the vehicle smoothly to stable position.

Human Factors Approach Towards Improving Readability Of Bus Schedules, Anand Tharanathan

Theses

Due to an increasing concern over the readability of existing bus schedules of a public transportation agency the schedule format was redesigned. Two prototype schedules were designed based on the gathered information from the literature survey, focus group meetings and data from other public transportation agencies' schedules. One of the prototypes was designed by giving primary importance to the direction of travel and was named the directional prototype schedule. The other prototype was designed by giving primary importance to the day of the week, and was named weekday / weekend prototype schedule. A time based laboratory experiment and a subjective …

Combining Systematic Layout Planning And Computer Simulation In The Design Of Manufacturing Facilities, Akintoye M. Akinyoade

All-Inclusive List of Electronic Theses and Dissertations

In this study, the systematic layout planning (SLP) and computer simulation were combined to improve the layout design of a manufacturing facility using a case study.

Modeling And Validation Of A Brake Hose, Jai Thomas

Masters Theses

Various computer aided design (CAD) softwares have the capability to depict rigid bodies in space accurately. However, the same is not true for the flexible components. This is because flexible components in an automobile are subject to large elastic deformations during the movement of the rigid components to which they are attached.

This research details the application of the principles of computation of the orientation of entities in a simplified coordinate system, vector mathematics, the file I/O features and structured C++ programming to view the rubber hose in CAD after modeling the hose using simulation software. Further validation of the …

The Relationship Of Project Team Attributes To Project Interim Performance, Vickie S. Parsons

Engineering Management & Systems Engineering Theses & Dissertations

The factors associated with project success, or failure, have not been conclusively resolved in the project management literature. The purpose of this research was to investigate the relationship of project team attributes and interim project performance using a statistical research design. An abundance of research has focused solely on the importance of technical project components as they relate to cost, schedule, or technical performance. However, research into internal team attributes has been sporadic and, generally, associated with subjective measures of project performance or less than optimal statistical techniques. Prior assessment of project performance has also been concentrated at project completion. …