Industrial Engineering Commons^™

Direct Ink Writing Of Shear Exfoliated Two-Dimensional Nanomaterial- Elastomeric Multifunctional Nanocomposite, Md Abdur Rahman Bin Abdus Salam, Asif Hasan Ridoy, A K M Abirul Haque, Muhammad Shahbaz Rafique, Md Arafat Hossain, Md Shahriar Forhad, Matthew G. Boebinger, Farid Ahmed, Karen Lozano, Ali Ashraf

Manufacturing & Industrial Engineering Faculty Publications

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman …

Nanostructured Cathode Catalysts For Aem Electrolysis: From Catalyst Design To Degradation And Hydrogen Dynamics, Yamini Kumaran

Electronic Theses & Dissertations (2024 - present)

Anion exchange membrane water electrolysis (AEMWE) presents a promising pathway toward cost-effective and sustainable hydrogen production by integrating the chemical robustness of alkaline systems with the compact, zero-gap design of proton exchange membrane electrolyzers. However, the widespread implementation of AEMWE is limited by the availability of highly active and durable platinum-group-metal (PGM)-free catalysts and by an incomplete understanding of their degradation behavior under realistic operating conditions.

This dissertation focuses on the development, characterization, and mechanistic investigation of nanostructured MoNi₄–MoO₂-based electrodes for efficient and stable hydrogen generation under alkaline and membrane-integrated environments. MoNi₄–MoO₂ nanorods …

Mitigating Out-Of-Plane Fiber Waviness In Afp Laminates With Tow-Gaps Via Selective Placement Of Thermoplastic Veils, Ahmadreza Ravangard, Kuthan Celebi, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Fiber tow-gaps and overlaps formed during the Automated Fiber Placement (AFP) process pose a significant challenge by introducing non-uniform composite morphologies, often characterized by resin-rich regions and fiber waviness. These defects occur as deposited fibers sink into the gap regions during consolidation, with gap geometry determined during path planning. Such morphological inconsistencies can compromise structural reliability by initiating premature failure, particularly through localized out-of-plane waviness and resin accumulation. This study investigates the integration of high melting temperature thermoplastic veils, specifically polyetherimide (PEI), into fiber tow-gaps as a method to prevent ply sinking and reduce fiber waviness on both internal and …

Pla Polymer Binder In Core Production - Influence On Final Casting Dimensions, Artur Soroczyński, Krzysztof Rechowicz

Virginia Digital Maritime Center (VDMC) Faculty Publications

The foundry industry is seeking an ecological alternative to synthetic molding resins. This study evaluates the technological properties of core sands bonded with biodegradable polylactide (PLA). Cores prepared on a 2% quartz sand matrix were subjected to casting processes using two alloys with extremely different pouring temperatures: gray cast iron (approx. 1200 °C) and AK11 silumin (approx. 710 °C). The research methodology included macroscopic assessment, dimensional analysis using 3D scanning (GOM Inspect), and qualitative knock-out assessment supported by numerical temperature field simulation. The results showed that the high crystallization temperature of cast iron leads to complete thermal degradation of the …

Inspection Planning Of Subsea Pipeline Using Risk-Based Inspection, Ni Luh Triska Adelia, Badrul Munir, Johny Wahyuadi Soedarsono

Journal of Materials Exploration and Findings

Pipelines are an important tool in oil and gas exploration. Pipeline is a transmission and liquid collection lines, including their accessories, which transport fluids from one plant to another. In transmission and collection process, there is a possibility of failure which can have minor to major impact on personnel injury, the environment and interrupt the business process. To maintain safety and to prevent accidents, the source and cause of failure needs to be calculated. Risk-based inspection (RBI) is a method that can be used to calculate the risk and determine the inspection planning both schedule and method, by combining the …

Optimizing The Expression Of Polyethylene Terephtalate Hydrolase-Encoding Synthetic Gene In Escherichia Coli Arctic Express (De3), Jocelyn Nataniel, Maria Ulfah, Dini Achnafani, Niknik Nurhayati, Gabriela Christy Sabbathini, Sri Rezeki Wulandari, Abinawanto Abinawanto, Is Helianti

Makara Journal of Science

The waste of polyethylene terephthalate (PET) plastic waste in Indonesia is a pressing concern due to its slow degradation and potential environmental damage. One promising solution is to utilize polyethylene terephthalate hydrolase from Ideonella sakaiensis (IsPETase), an enzyme that specifically degrades PET. However, inducing the expression of IsPETase synthetic gene in Escherichia coli BL21 (DE3) has been challenging because much of it remains insoluble. This study aimed to express IsPETase in E. coli Arctic Express (DE3) and optimize the conditions to enhance its production. First, pET22b(+)pelB-IsPETase was inserted into E. coli Arctic Express (DE3). The …

Study On Human Integrity Management System Maturity Level For Supporting Asset Integrity And Process Safety Implementation, Anggiat M. Sihotang, Dedi Priadi, D. Rizal Asral

Journal of Materials Exploration and Findings

The human factors (HF) are recognized as one of critical process safety barriers involved in normal and abnormal conditions in the oil and gas industry. In order to strengthen the HF roles as barriers we need to ensure that the actions generated are based on a valid risk assessment of the operation to be addressed by a relevant human factor analysis. Organizations within the oil and gas process have made much progress in understanding and implementing HF improvement programs. However, organizations are not always clear about what are their current situations in managing HF, their priorities for HF to be …

Assessing Adoption Barriers Of Sustainable Packaging In Egypt, Carol Ramses Morgan

Theses and Dissertations

Sustainable packaging has become an essential part of business decisions and corporate directions. With the rise of environmental damages due to improper waste management and unsustainable practices, businesses have a major responsibility to analyze their products’ life cycles and redesign them with sustainability in mind. Applying sustainable packaging could save companies large amounts of resources, therefore cutting costs, while also achieving the legal and social duty as a corporation towards society and the environment. Many developing countries, with specific focus on Egypt, have recently focused on legislative and corporate decisions in order to encourage more sustainable practices. Egypt’s new Waste …

Laser Deposition Additive Manufacturing Of Multi-Material And Metal-Ceramic Composite Structures, Manikanta Grandhi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing performance requirements of modern industrial systems, coupled with the imperative for decarbonization, necessitate a fundamental rethinking of metallic component design and manufacturing. Traditional materials, with their inherent limitations in property optimization, susceptibility to degradation, and weight constraints, are proving insufficient. Multi-material joining offers a potential solution, enabling designers to strategically integrate diverse materials with specific, tailored properties into single component. Functionally graded materials (FGMs) and oxide dispersion strengthened (ODS) materials are prime examples of this approach, delivering substantial improvements in wear resistance, thermal regulation, high-temperature resilience, and overall weight efficiency. However, conventional manufacturing approaches further exacerbate the limitations …

Higher-Order Effects In Biaxial Flexure Of Gfrp I-Section Beams, Zia Razzaq, Faridoon Z. Razzaq

Civil & Environmental Engineering Faculty Publications

A theoretical study of Glass Fiber Reinforced Polymer (GFRP) beams subjected to biaxial bending moments is presented with a focus on the influence of higher-order effects on maximum normal stresses. It is shown that the biaxial bending type of loading causes a dramatic increase in the maximum normal stress for a GFRP beam when induced torsional effects are included. The study demonstrates that the traditional first-order theory can grossly underestimate the maximum normal stress in a GFRP beam. Based on the numerical results presented using a higher-order theory which also accounts for induced warping normal stresses, the maximum normal stress …

Functionally Magnetic Gradient Copper-Nickel Material Fabricated Via Directed Energy Deposition, Vy Tran Phuong Nguyen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Functionally gradient materials (FGMs) of CuSn10 and Inconel 718 were fabricated via a hybrid directed energy deposition (DED) system. The objective of the present thesis is to determine the feasibility of manufacturing CuSn10 and Inconel 718 FGMs via DED and investigate the physical and mechanical properties and the microstructures of the resulting FGMs. The physical tests comprised of conductivity and Seebeck coefficient measurements. The microstructure analysis and mechanical testing include microscopic imaging, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and hardness test. In addition, compressive strength test was performed to analyze the interface bonding behaviors.

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Minimizing Leakage In Thin Walled Structures Printed Through Selective Laser Melting, Andrew Spencer Yap

Master's Theses

In this project, the scan strategy of selective laser melting (SLM) for thin walled structures was investigated by changing laser parameters and tool path. Producing thin walled structures is difficult due to defects such as warpage and porosity. A layer on the SLM 125 consists of hatch volume, fill contours, and borders, however, for thin walls, hatch volume can become unavailable, resulting in a solely border/fill contour laser tool path.

Three central composite designs (CCD) were created to optimize the laser parameters of borders to minimize leakage rate and porosity. The two factors changed were border laser power and scanning …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Assessment Of Heavy Metal Concentration In Soils Around Geita The Gold Mine, Tanzania, Mariam G. Mgendi, Mkabwa L. K Manoko, W.J.S. Mwegoha, C. Southway C. Southway

Journal of Humanities and Social Sciences

Health issues related to gold mining cannot be underestimated. Gold mining produce acid mine drainage (AMD), which in turn releases heavy metals into the nearby environment, hence causing environmental pollution. Heavy metals are naturally very toxic, thus pose a great health concern especially when their concentration exceeds the recommended permissible limits. In this study, concentrations of five heavy metals—including Pb, Ni, Cr, Cu and Zn—were assessed in the soil around Geita Gold Mine (GGM). A total of 17 sampling sites were established from which the soil samples were collected at 0-15cm and 15-30cm soil depth. The concentration of both total …

The Development Of A Holistic Quality Score Using In-Situ Monitoring Of Laser Powder Bed Fusion, Ryan Daigneault

College of Graduate Studies: Theses & Dissertations

Additive manufacturing processes allow for a great degree of flexibility in terms of part production. The process is autonomous once the part has started printing in that the operator generally does not need to intervene until the part is finished. One issue that this introduces, however, is an inability to determine part quality during the printing process. Once a part has started printing, the operator must either wait until the part is finished or regularly check on the part during the print to determine the part quality. Using data gathered from multiple sensors, a quality score can be used to …

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Product Realization Capstone: Element Proof Safety Steps For Willie Price Lab School, Catherine Thomas, Allan Heuerman, Jared Mumme

Honors Theses

The purpose of this document is to describe the process we took to complete our capstone which paired the Center for Manufacturing Excellence with the Willie Price Lab School. The goal of the capstone was to remake step stools for the students of Willie Price, as the last stools failed to withstand weather damage. However, with the COVID-19 pandemic, plans were hindered, shifting the goal from actually producing the steps to creating instructions so that a younger Center for Manufacturing class could complete the production at a later date. Standardized Work Instructions, a detailed production plan, and engineering drawings were …

Investigation Of Chip-Form And Tool-Wear In Turning Of Hardened Af9628 Alloy Under Various Cooling And Lubrication Conditions, Jason Wolf

Theses and Dissertations--Manufacturing Systems Engineering

Next generation defense and commercial applications for structural steels require new alloys that eliminate or reduce critical elements from their composition to lower cost and improve manufacturability, while maintaining or exceeding high strength and toughness requirements. A new alloy, denoted as AF9628, has recently been developed for this purpose and its manufacturing characteristics and the material response in component manufacturing must be fully understood.

In the present study, hardened AF9628 alloy was turned with a coated carbide cutting tool under fixed cutting speed, feed rate, and depth of cut parameters. This work focuses on chip-form and tool-wear analysis to understand, …

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

Communication And Biodegradable Packaging Relationship: A Paradigm For Final Disposal, Breno Luiz Ottoni, Rafael Mattos Deus, José Alcides Gobbo Junior, Ângela Maria Grossi De Carvalho, Rosane Aparecida Gomes Battistelle

Journal of Applied Packaging Research

Solid waste generation is estimated to increase from 1.3 billion to 2.2 billion tons by 2025, causing environmental, social, and consequently public health problems. The biggest problem in this regard involves the inadequate disposal of waste, and in emerging countries like Brazil, it is sorted less waste for recycling or composting. In this context, plastic packaging is more complex due to the high polymer composition, as well as low recycling rates. Bioplastics appear as alternatives because they are mostly biodegradable. Given the various functions of packaging and a systematic review of the literature, the aim of this study was to …

Life Cycle Sustainability Analysis (Lcsa) Of Polymer-Based Piping For Plumbing Applications, Andy J. Rivas Bolivar

Senior Honors Projects, 2010-2019

Water conveyance systems play a critical role in modern developed areas. Polymer pipes have been used for about a century, and their convenient physical properties have positioned polymers as the leading material in the piping industry. Having such influence in the market means that changes in current material selection and manufacturing could lead to significant reductions in the footprint associated with their products. Currently, there are no comparative lifecycle assessments that evaluate the different polymer selections commercially available, which makes it hard to determine what products have the least impact on the environment. Understanding how such impacts are relative to …

The Effect Of Process Parameters And Surface Condition On Bond Strength Between Additively Manufactured Components And Polymer Substrates, Bharat Bhushan Chivukula

Graduate Theses and Dissertations

Additive patching is a process in which printers with multiple axes deposit molten material onto a pre-defined surface to form a bond. Studying the effect of surface roughness and process parameters selected for printing auxiliary part on the bond helps in improving the strength of the final component. Particularly, the influence of surface roughness, as established by adhesion theory, has not been evaluated in the framework of additive manufacturing (AM). A full factorial design of experiments with five replications was conducted on two levels and three factors, viz., layer thickness, surface roughness, and raster angle to examine the underlying effects …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Spare Parts On Demand Using Additive Manufacturing : A Simulation Model For Cost Evaluation., Stefan Jedeck

Electronic Theses and Dissertations

Little is known about the impact of additive manufacturing in the spare part supply chain. A few studies are available, but they focus on specific parts and their applications only. A general model, which can be adapted to different applications, is nonexistent. This dissertation proposes a decision making framework that enables an interested practitioner/manager to decide whether using additive manufacturing to make spare parts on demand is economical when compared to conventional warehousing strategy. The framework consists of two major components: a general discrete event simulation model and a process of designing a wide range of simulation scenarios. The goal …

Comparison Of Low-Temperature Co-Fired Ceramic And Direct Bonded Copper For Single Ended Primary Inductance Topology, Kristopher Cody Johnson

Electrical Engineering Undergraduate Honors Theses

This work examines the thermal dissipation characteristics of Low-Temperature Co-fired Ceramic (LTCC) and Direct Bonded Copper (DBC) with the implementation of a Single Ended Primary Inductance Converter (SEPIC) topology. The advantages and disadvantages of the two substrates will be explored in addition to a description of the design and control of the SEPIC. It will be shown that the DBC implementation is superior with regards to thermal dissipation, but that LTCC has advantages in high- density packaging, RF applications, and embedded components. These substrates and converters provide many advantages in industrial applications that include automotive and grid level implementations. Additional …

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …