Industrial Engineering Commons^™

Handling Of Syringe Sharps In A Non-Incineration Health Care Waste Disposal, Tito Mwinuka

Tanzania Journal of Engineering and Technology (TJET)

An attempt has been made by the R&D team of the University of Dar es Salaam to design and manufacture two needle cutter prototypes, a manually operated and an automatic needle cutter to be used in rural and urban areas, respectively. This is part of the UNDP and WHO efforts aimed at promoting the non-burn medical waste disposal technologies in developing countries such as Argentina, India, Latvia, Lebanon, Philippines, Senegal, Tanzania and Vietnam. The project also involves designing and manufacturing of the autoclaves for sterilizing of needle cutters and other infectious medical waste. The use of needle cutters in hospitals …

Design And Manufacture Of A Waste Compactor Prototype: A Step Towards Implementing A Non-Burn Health Care Waste Disposal In Developing Countries, Tito Mwinuka

Tanzania Journal of Engineering and Technology (TJET)

Non-burn technology is the only safe way of handling and disposing infectious healthcare waste. It involves steam treatment of infectious waste at temperatures higher than 121 o C for a minimum of 30 minutes before disposing them just like other municipal waste. Infectious healthcare waste is normally only about 10 25% of all healthcare waste. In this paper, design, manufacturing and testing of a waste compactor for reducing waste volume to facilitate its handling is discussed. Preliminary tests show that the waste volume can be reduced to less than 10% of its original volume using the developed compactor. Waste compactors …

Fatigue Analysis Of The Welded Region In The Automotive Torsion Beam Rear Suspension System, Nan Zhan, Xiaochuan Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Spare Parts On Demand Using Additive Manufacturing : A Simulation Model For Cost Evaluation., Stefan Jedeck

Electronic Theses and Dissertations

Little is known about the impact of additive manufacturing in the spare part supply chain. A few studies are available, but they focus on specific parts and their applications only. A general model, which can be adapted to different applications, is nonexistent. This dissertation proposes a decision making framework that enables an interested practitioner/manager to decide whether using additive manufacturing to make spare parts on demand is economical when compared to conventional warehousing strategy. The framework consists of two major components: a general discrete event simulation model and a process of designing a wide range of simulation scenarios. The goal …

Modeling Reliability Growth In Accelerated Stress Testing, Jason K. Freels

Theses and Dissertations

Qualitative accelerated test methods improve system reliability by identifying and removing initial design flaws. However, schedule and cost constraints often preclude sufficient testing to generate a meaningful reliability estimate from the data obtained in these tests. In this dissertation a modified accelerated life test is proposed to assess the likelihood of attaining a reliability requirement based on tests of early system prototypes. Assuming each prototype contains an unknown number of independent competing failure modes whose respective times to occurrence are governed by a distinct Weibull law, the observed failure data from this qualitative test are shown to follow a poly-Weibull …

Development And Validation Of A Model For Granular Material Volume Measurements, Pourya Fasounaki

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Keeping inventory record of packed grains in silos poses challenges since the bulk material’s different segments do not discharge uniformly, leading to formation of random peaks and valleys on the surface. To facilitate obtaining accurate volume measurement of the grains by taking into account this non-linear behavior on the surface, laser or plumb-bob level-sensing devices are employed at different part of the surface to probe the level of material under those regions.

The main goals of this research is to study the behavior of granular material in silo while discharging downward and by doing so, differentiate certain flow patterns formed …

Case Studies: In-Situ Rebuilding Of Damaged Rope Drum Shafts Of Ssg Crane And The Repair Of Circumferential Crack Of Cement Kiln By Welding, Joseph Runyoro

Tanzania Journal of Engineering and Technology (TJET)

Material failures in engineering are characterized by unwanted downtime of equipment and require the application of sound engineering principles to rectify the problem so that it does not reoccur. The most widely method for repairing damaged steel structures such as rope drum shaft or cracked cement kiln is by Manual metal arc welding. The equipment mentioned have their main importance that, when they are broken down, they cost a lot of money in lost revenue and affects a lot of people in terms of business and livelihood. The nominal diameter (DN) 240 rope drum shaft was damaged when the roller …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Design Approach For Small Scale Continuous, Steady State Plants, O Kaunde

Tanzania Journal of Engineering and Technology (TJET)

One of the major steps in the design of a process plant is development of an appiopriate flowsheet. At this step, the technical solutions may be con- sidered in relation to the social and economic factors. In this paper, guide- lines for developing a flowsheet for continuous, steady State process in a developing country environment have been proposed. To illustrate the pro- posed guidelines, a case study involving design of an ethanol distillation plant has been used.

Improved Heat Transfer By Means Of Steam Injection In A Shell & Tube Heat Exchanger, O Kaunde

Tanzania Journal of Engineering and Technology (TJET)

When designing a heat exchanger; one aims at attaining high heat transfer rates SO as to minimise heat transfer area and therefore the overall cost. This paper presents a method of improving the overall heat travsfer coef- ficient of a conventional shell and tube heal exchanger. The method in- volves injecting steam into the process fluid as it enters the heat exchanger thus effecting mixing of fluid as it travels along the exchanger Tests car- • ried out using this technique showed a significant increase in the overall heat transfer coefficient values.

Measurement Of Dust Resistivity And The Effect Of Filter Operating Parameters On Its Value, S Issangya

Tanzania Journal of Engineering and Technology (TJET)

Methods of measuring electrical sensitivity of a dust layer have been outlined and the porous electrodes cell was used to measure the electrical resistivity of a dust layer and to determine the influence of various parameters. Dust layer thickness and applied voltage had no influence. Resistivity depended on particle size, packing density, temperature, and air relative humidity. Glass beads and limestone powders of different mean particle sizes were used. Temperature was varied from 20–100 °C and air moisture ranged from dry to near saturation. The results may help in understanding the performance of electrically enhanced fabric filters, which are influenced …

Quality Problems Facing Tanzanian Industrial Firms, M Msafiri

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on the results of a study of quality problems facing Tanzanian industrial firms. The results show that Tanzanian firms do not set goals with respect to quality and quality management, thus their qual- ity performance is generally poor. A Ithough there are a number of opera- tional problems constraining the companies, the main problems lie with the internal management of the quality function. Extensive ideas and sug- gestions for improving the performance of the quality function are given.

Optimum Design For Spring With Orthogonal Design Method, Han Fu - Jie

Tanzania Journal of Engineering and Technology (TJET)

Orthogonal design method is a sort of direct optimum method, by which the op- timal result may be obtained through simple computation and analysis. This method has gained increasingly extensive interest in scientific research, engineering design, end production management as well. The orthogonal table is the basic instrument for carrying out optimum design with orthogonal design method. It is a mathernatical table established On the basis Of the idea of isostatic distribution. As various levels may appear in any column, it makes a partial experiment contain levels of all factors furthermore. RII combina- tions of any two columns may appear …

Production Of Blanking Circles And Dies - An Appropriate Method, V Bhandari

Tanzania Journal of Engineering and Technology (TJET)

A large important blanking die for production of multiwick stoves oil tanks was damaged beyond repair during normal maintenance. A replacement die could not be made available immediately. Initially an alternative blank production system based upon the adaptation of the inhouse and locally available tools was set up. Subsequently a temporary low cost and a permanent replacement blanking die was designed, developed and manufactured out of pad welding of mild steel plate. Recommendations have been drawn in light of the experiences gained in the deployment of these appropriate methods.

Distributive Mixing Performance Of Rubber Internal Mixers, B Mutagahywa

Tanzania Journal of Engineering and Technology (TJET)

Results of experiments to study the distributive mixing performance of Internal mixers are reported in this paper. Distributive mixing was assessed by monitoring the uniformity of sulphur distribution throughout rubber mixes subjected to a range of rotor revolutions. The results indicate that distributive mixing in a well controlled Internal mixer is rapid and unlikely to be a source of mix variability.

Its Shearing Time, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

SHEARING will soon be taking place on your property. For a smooth annual wool harvest, remember:—

Test Of High-Speed Engine, William Frazier Owen

Student and Lippitt Prize Essays

Discusses the best ways in which a steam engine can function by using measurements from an actual steam engine. The essay ultimately determines that a steam engine is at its highest efficiency when carrying the largest load possible.