Operations Research, Systems Engineering and Industrial Engineering Commons^™

A Simulation Approach To Granite Sentry System Analysis, Marilyn J. Bauer

Theses and Dissertations

This study demonstrated the use of simulation modelling to analyze Granite Sentry system performance. The availability simulation model constructed provides a number of system performance measures as a function of component MTBFs and MTTRs. Analysis of failure data prior to model construction supported the generally accepted use of exponentially distributed failure rates and lognormally distributed repair times.

Proactive Monitoring Of Performance In Stochastic Communication Networks, John C. C. Van Hove

Theses and Dissertations

This research proposes several models for placing bounds on the expected values of some dynamic performance measures for computer communication networks with failing components. These models provide an understanding of expected network performance that is useful in the process of proactive performance monitoring and also in defining level of service agreements with network users. There were three objectives for this research. The first objective was to extend some existing models of steady-state stochastic network performance to a dynamic network flow representation in order to capture the dynamic nature of proactive monitoring. The second objective was to convert the extended absolute …

An Investigation Of Simulated Annealing Applied To Structural Optimization Problems, Richard C. Mceachin

Theses and Dissertations

This thesis investigates the feasibility of using Simulated Annealing SA in structural optimization problems. The investigation involves solving benchmark structural optimization problems with an SA algorithm, and comparing its solutions to those found by four other optimizers. Overall, the analysis shows that SA has limited applicability in structural optimization. Two primary factors were found to adversely impact the performance of the SA algorithm in these problems. These factors are high dimensionality, and high levels of constraint. The difficulty involved in solving these problems with a random search increases exponentially with the number of dimensions. The number, and non-linearity, of the …

Application Of Sequential Quadratic Programming To Large-Scale Structural Design Problems, Mark A. Abramson

Theses and Dissertations

Large-scale structural optimization problems are often difficult to solve with reasonable efficiency and accuracy. Such problems are often characterized by constraint functions which are not explicitly defined. Constraint and gradient functions are usually expensive to evaluate. An optimization approach which uses the NLPQL sequential quadratic programming algorithm of Schittkowski, integrated with the Automated Structural Optimization System ASTROS is tested. The traditional solution approach involves the formulation and solution of an explicitly defined approximate problem during each iteration. This approach is replaced by a simpler approach in which the approximate problem is eliminated. In the simpler approach, each finite element analysis …

The Effective Use Of Animation In Simulation Model Validation, Christopher L. Swider

Theses and Dissertations

This study examined two animation displays moving icons, bar graphs at two presentation speeds to determine how each of these factors affected the animations ability to communicate violations of model assumptions. Subjects viewed animation displays individually and in combination at each presentation speed. Eight problem scenarios were presented to evaluate each animations ability to communicate violations of different assumptions. Each animations communication ability was measured subjectively and objectively. Subjective measures in the form of pairwise comparisons were used to calculate normalized preference ratings for each animation. objective measures included problem identification accuracy and problem time. Subjective results indicated that moving …

An Air Mission Planning Algorithm For A Theater Level Combat Model, Brian J. Griggs

Theses and Dissertations

This thesis describes the development of an air mission planning algorithm for the Joint Staffs Future Theater Level Model FTLM. The overall problem scope was to develop an algorithm to handle major factors bearing on the combat mission planning problem while providing hook-ups for the FTLM architecture. Other aspects of the problem included finding the appropriate level of detail, developing a fast solving technique, and attempting to use existing data. The problem was handled by using some ideas from existing aircraft allocation algorithms and by adding some new techniques. The proposed air mission planning algorithm supplies the optimum degree of …

Assessing The Vulnerability Of Multi-Commodity Networks With Failing Components, Alan R. Robinson

Theses and Dissertations

This research proposes an analytical approach for assessing flow disturbance, or compromise, based on limited sampling of arc flow information in multi-commodity, or multiple origin-destination O-D, networks with failing arcs. There were three objectives established for this research. The first objective was to bound the expected flow, given the arcs fail with certain probabilities, which was accomplished by reviewing current approaches for single-commodity networks and extending the results to the multi-commodity case. The second objective was to determine the best placement of flow monitors to obtain the most accurate estimates of O-D pair volumes. This was accomplished using a multi-criteria …

A Fortran Based Learning System Using Multilayer Back-Propagation Neural Network Techniques, Gregory L. Reinhart

Theses and Dissertations

An interactive computer system which allows the researcher to build an optimal neural network structure quickly, is developed and validated. This system assumes a single hidden layer perceptron structure and uses the back- propagation training technique. The software enables the researcher to quickly define a neural network structure, train the neural network, interrupt training at any point to analyze the status of the current network, re-start training at the interrupted point if desired, and analyze the final network using two- dimensional graphs, three-dimensional graphs, confusion matrices and saliency metrics. A technique for training, testing, and validating various network structures and …

Materials Recovery Facilities In The United States Virgin Islands: A Regional Facilities Location Model Study, Lloyd O. Prince Jr.

Engineering Management & Systems Engineering Theses & Dissertations

Continental municipalities have derived many benefits from the economies of scale associated with a regional approach to facilities location and management planning. Centralized solid waste processing facilities is an example. Island communities, however, surrounded by miles of ocean, are constrained to a fragmented approach to the facilities location solution. This research was conducted to determine if the regional paradigm suggested in the literature is applicable to a set of island communities connected by an ocean transportation infrastructure. A linear programming (LP) model, constraints and data requirements were developed and applied to a network of islands. A series of hypothetical material …

A Check Parameter Method For Use In Designing Relays, H Kadete

Tanzania Journal of Engineering and Technology (TJET)

Low quality magnetic steel available locally has been successfully used as core material for a relay. New design principles as well as construction procedure used in development of a prototype are presented. Then the new approach is assessed and found to deliver acceptable accuracy.

Synthetic Battlebridge: Information Visualization And User Interface Design Applications In A Large Virtual Reality Environment, Kirk G. Wilson

Theses and Dissertations

With shrinking budgets and fewer personnel, future military training will rely heavily on simulated environments. The goal for this training is to reduce cost while maintaining readiness and unparalleled capability for all levels of military command. This thesis effort, the Synthetic Battle Bridge SBB , provides a real-time simulated environment for military commanders to observe on-going computer simulations of varying participation levels and helps them wring the most from a simulation. The SBB, designed for higher ranking personnel with little time to spend learning how to run the system, must exhibit three capabilities ease-of-use, long-term retention, and adaptability. Based on …

Integration And Enhancement Of The Saber Wargame, Karl S. Mathias

Theses and Dissertations

The Saber wargame is a theater-level air/land battle wargame written in Ada that is being developed for the Air Force Wargaming Center at Maxwell AFB, AL. This thesis documents how the user interface and simulation engine were integrated. Integration was accomplished by developing a portable object-oriented database system (OODBMS) interface. The interface was implemented in Ada and tied to an OODBMS also written in Ada. Using the interface, both subsystems were able to work from a consistent database and exchange information. The user interface was enhanced by converting it from the Software Technology for Adaptable Reliable Systems Ada/X Window System …

A Parametric Regression Of The Cost Of Base Realignment Action (Cobra) Model, Douglas D. Hardman, Michael S. Nelson

Theses and Dissertations

This study develops a parametric model that is capable of generating accurate estimates of the costs to close Air Force installations. The new model is based upon, but much simpler to use than, the Cost of Base Realignment Action (COBRA) model. COBRA is an economic cost analysis model that requires a minimum of 250 inputs and as many as 700 inputs. The new parametric model requires just 10 input variables and was developed using least squares multiple regression. Comparison of the new parametric model to COBRA indicates that it captures 91 percent of the variance in cost estimates generated by …

Optimum Design For Spring With Orthogonal Design Method, Han Fu - Jie

Tanzania Journal of Engineering and Technology (TJET)

Orthogonal design method is a sort of direct optimum method, by which the op- timal result may be obtained through simple computation and analysis. This method has gained increasingly extensive interest in scientific research, engineering design, end production management as well. The orthogonal table is the basic instrument for carrying out optimum design with orthogonal design method. It is a mathernatical table established On the basis Of the idea of isostatic distribution. As various levels may appear in any column, it makes a partial experiment contain levels of all factors furthermore. RII combina- tions of any two columns may appear …

Optimal Silo Attack Plan For The Red Integrated Strategic Offensive Plan (Risop), Richard C. Pace

Theses and Dissertations

The Joint Staff Directorate for Force Structure, Resources, and Assessment (J-8) sought a procedure which could be used to generate an optimal missile allocation for the silo attack portion of the Red Integrated Strategic Offensive Plan (RISOP). Their current solution procedure is a manual heuristic which is time-consuming and is not guaranteed to lead to an optimal solution. J- 8 defines an optimal solution as a feasible solution which minimizes both the flight time of the missile that impacts first and the duration of the attack. J- 8 defined several input rules which limit how missiles may be allocated. A …

An Analysis Of The Generalized Lambda Distribution, Robert J. Bergevin

Theses and Dissertations

The Generalized Lambda Distribution (GLD) is a four parameter function that is capable of mimicking the behavior of a wide range of probability density functions (pdfs). Unfortunately, the GLD presently cannot model every possible type of pdf. Since the reasons for this limitation are unknown, this thesis examines several potential problems in an attempt to expand the range of distributions the GLD can mimic. We first present a discussion of the behavior of the algorithm that is used to search for the appropriate GLD parameter values. In particular, we examine the effect of using an unconstrained search to find the …

Modified Anderson-Darling And Cramer-Von Mises Goodness-Of-Fit Tests For The Normal Distribution, David A. Gwinn Sr.

Theses and Dissertations

New techniques for calculating goodness-of-fit statistics for normal distributions with parameters estimated from the sample are investigated. Samples are generated for a Normal(0,1) distribution. Critical values are calculated for five modifications to the Anderson-Darling statistic and five modifications to the Cramer-Von Mises statistic. An extensive power study is done to test the power of the new statistics versus the power of the unmodified statistics. Powers of six of the new statistics show minimal to no improvement, two of the new statistics show a marked decrease in power, and two of the new statistics show an overall increase in power over …

Including Maximum Sustained Wind Speed In A Time Series Model To Forecast Hurricane Movement, Timothy B. Mott

Theses and Dissertations

Techniques for applying time series fundamentals to forecasting hurricane movement are thoroughly examined in this research. The objectives are: (1) to modify Dr. Thomas Curry's threshold autoregressive time series model to improve its ability to forecast hurricane movement, (2) to forecast the maximum sustained wind speed for a hurricane, and (3) to identify if wind speed should be included as an explanatory variable to aid in forecasting hurricane movement. Eleven different models to predict the latitude, longitude and maximum sustained wind speed are compared and contrasted with Curry's bivariate time series model. The results showed the modifications allow significant forecasting …

A Comparison Of Variable Selection Criteria For Multiple Linear Regression: A Second Simulation Study, David P. Woollard

Theses and Dissertations

This thesis implements a variable selection method proposed by Alan J. Miller, and makes an extension of Ross J. Hansen's 1988 thesis research by comparing the methods he examined: Minimum MSE, Minimum Sp, and Minimum Cp with Miller's method. Response Surface methodology is employed with two performance measures: the percentage of correct variables in a model and the Theoretical Mean Squared Error of Prediction (TMSEP). Each technique is applied on generated data with known multicollinearities, variances, random predictors, and sample sizes. Both performance measures are computed for models selected under each technique. A full factorial design using each performance measure …

A Fuzzy Logic Optimal Control Law Solution To The Cmmca Tracking Problem, Randy E. Nelson

Theses and Dissertations

The Air Force uses the C-18 Cruise Missile Mission Control Aircraft (CMMCA) to radar track cruise missiles (CM) during test flights. Because of the complexity of the CM flight profiles, maintaining radar coverage at all times is very difficult. This thesis attempted to apply optimal control theory to construct a simulation providing 100% radar coverage. The simulation was divided into ten second intervals, and fuzzy logic was used at the start of each interval to determine the set point, i.e., that point in space where the CMMCA should be in ten seconds. The set point calculation's fuzzy logic balanced CMMCA …

A Modified Anderson Darling Goodness-Of-Fit Test For The Gamma Distribution With Unknown Scale And Location Parameters, Tamer Ozmen

Theses and Dissertations

A new modified Anderson-Darling goodness-of-fit test is introduced for the three-parameter Gamma distribution when the location parameter is found by minimum distance estimation and scale parameter by maximum likelihood estimation. Monte Carlo simulation studies were performed to calculate the critical values for A-D test when A-D statistic is minimized. These critical values are then used for testing whether a set of observations follows a Gamma distribution when the scale and location parameters axe unspecified and are estimated from the sample. Functional relationship between the critical values of A-D is also examined for each shape parameter by the variables, sample size …

A Modified Chi-Squared Goodness-Of-Fit Test For The Three-Parameter Gamma Distribution With Unknown Parameters, Thomas J. Sterle

Theses and Dissertations

A modified chi-squared goodness-of-fit test was created for the gamma distribution in the case where all three parameters must be estimated from the sample. Critical values are generated using a Monte Carlo simulation procedure with 5000 repetitions each. Random samples of 8 different sizes were drawn from gamma distributions with shape parameters 1, 1.5, 2., and 2.5. The shape, scale, and location parameters were then estimated from each sample, using an iterative technique combining the maximum likelihood and minimum distance methods, enabling, computation of the chi-squared statistics and critical values. The same process is used to generate random samples, parameter …

A New Goodness-Of-Fit Test For The Weibull Distribution Based On Spacings, Mark C. Coppa

Theses and Dissertations

The critical values for a new goodness-of-fit test based on spacings are generated for the Weibull distribution when the shape parameter is known. The critical values are used for testing whether a set of observations follow a Weibull distribution when the scale and location parameters are unknown. A Monte Carlo simulation with 10,000 iterations is used to generate the critical values for sample sizes 5(5)35 at shape parameters k equal to 0.5(0.5)1.5 and for sample sizes 5(5)20 at shape parameters k = 2.0(1.0)4.0. A Monte Carlo power study of the Z* test statistic using 5000 iterations is accomplished using nine …

The Use Of A Factory Simulation To Evaluate A Flexible Control Structure For Integrated Manufacturing, Ling Ling Pan

Engineering Management & Systems Engineering Theses & Dissertations

Once a control structure for an integrated manufacturing system is decided upon, manufacturing activities are limited by that structure. A flexible control structure is presented as an approach for accommodating a variety of manufacturing activities, without being limited to a single control structure. A flexible control structure is one that allows multiple types of control structure in the manufacturing process. For example, both hierarchical and non-hierarchical structures may be used in a flexible structure. The properties of a flexible control structure are discussed from the point of view of graph theory.

Control structures for automated manufacturing are difficult to evaluate …

Reliability Trend Analyses With Statistical Confidence Limits Using The Luke Reliability Trend Chart, Stephen R. Luke

Engineering Management & Systems Engineering Theses & Dissertations

In electronic systems, it is interesting to understand exactly how the reliability is changing with time. Dynamic performance changes when a system passes from infant mortality stage into useful life phase and when the system passes from useful life phase into wearout phase. Dynamic performance also changes when the system is redesigned or when the system is acted on by a number of other outside forces such as a change in maintenance policy, escalation of alignment problems, or a change in training program. It is important to know when a system is changing dynamically in order to assess design, policy …

Multidimensional Approach To Implementation Of Continuous Process Improvement Utilizing Small Run Analysis In A Shipyard Environment, Paul Ray Hollandsworth

Engineering Management & Systems Engineering Theses & Dissertations

Nationally, both public and private shipyards are experiencing a high rework rate (over 40%) in the fabrication of plug connectors used for electronic systems onboard Navy vessels. The shipyard's survival depends on acquiring the elements necessary to maintain a major industry in a position of continuous improvement that produces a better product than their competitors, at less cost, in a safe manner, and on schedule.

This research addresses the complex problem of how to introduce quality control methodologies within a job shop environment that assists in identifying variables that influence the rework rate of plug fabrication process over a four …

An Assessment Of Software Safety As Applied To The Department Of Defense Software Development Process, Peter W. Colan, Robert W. Prouhet

Theses and Dissertations

This research analyzed the relationships between the DOD software development process, system safety requirements, and current structured software safety analysis techniques. The current state of software safety was assessed within the aerospace industry and DOD, and a training program for DOD System Safety Managers was developed. A telephone survey was conducted to gather information on current software safety analysis techniques and methodologies. Personal interviews were conducted with Aeronautical System Center System Safety Managers to gather data on job perception and perceived training needs. The results of the study indicate that the DOD guidance and policy documents needed to implement and …

An Integrated Simulation Model Development Environment For Slam Ii Using Object-Oriented Paradigm, Rizvan Erol

Masters Theses

An integrated simulation model development environment was implemented to assist the modeler by automating certain activities of simulation modeling. The system included interactive model definition, experimental design, automatic simulation program generation in SLAM II. Object-oriented paradigm at software development stage was extensively used to conceptualize the structure, and rules of the SLAM II language in order to generate efficient, and modular program code. The present system targeted modeling of various probabilistic inventory control system problems. The remarkable advantages of the system were rapid model development time, and achieving reliable program code without requiring any knowledge in SLAM II. Object-oriented programming …

Comparison Of Artificial Neural Networks With A Conventional Heuristic Technique For Optimization Problems, Jeffrey S. Gruner

Theses and Dissertations

This research investigates the utility of the Hopfield and Kohonen artificial neural networks to the traveling salesman optimization problem. A third, non-neural-network technique (the Christofides Algorithm - a competitive, bounded-solution operations research technique) is also investigated for comparison to the artificial neural network solutions. An eight and forty-two city distribution are chosen for comparison of the solutions.

Software Support Measurement And Estimating For Oracle Database Applications Using Mark Ii Function Points, Steven D. Radnov

Theses and Dissertations

This study investigated the results of measuring software support of Oracle database applications and estimating the effort and schedule required to provide support. Software measurement was accomplished with a variant of the function points metric, called Mark II function points, which is comprised of three weighted parameters, inputs, entities, and outputs. A technique for mapping Mark II function points to Oracle DBMS components was developed, and the size of the software support for each project, per team, was measured by tabulating and weighting the number of inputs, entities, and outputs that are added, changed, and/or deleted. Software support effort was …