Operations Research, Systems Engineering and Industrial Engineering Commons^™

On The Issue Of Developing Diagnostic Systems In Case Of Incompleteness Of Data, Amanulla Azizovich Kadirov, Shohijahon Ulugbek Ugli Akhmetov

Technical science and innovation

This paper addresses the problem of developing diagnostic systems for industrial equipment when initial failure data is incomplete or unavailable. An approach is proposed for generating synthetic data based on a pseudo-failure generator that implements stochastic modeling of degradation processes. A formalized algorithm for generating time-to-failure samples has been developed, including stages of failure physics analysis, statistical model selection, distribution parameterization, and simulation of operating conditions. The Weibull distribution is used as the base model, allowing for the consideration of various stages of the equipment’s life cycle. Additionally, factors that bring the synthetic data closer to real operating conditions are …

Mathematical Modelling Of Nitrification And Denitrification Processes Based On Neuro-Fuzzy Bioreactor Models, Mirkhalil Agzamovich Ismailov, Boburbek Zokirjon Ugli Mannobjonov

Technical science and innovation

This paper presents the development and investigation of hybrid neural network and fuzzy models for the mathematical modelling of nitrification and denitrification processes in a biological wastewater treatment bioreactor. A comprehensive approach is proposed, integrating a mechanistic model of the ASM1/ASM2d type with neural networks (LSTM and Gaussian Process Regression), as well as a fuzzy control system based on an extended set of expert rules. A digital twin of the bioreactor was developed to allow for the prediction of the dynamic behavior of key parameters such as NH₄⁺, NO₃⁻, dissolved oxygen, etc. within a prediction range of 1 to 12 …

Integrating Gis With Interim Payment Valuation In Road Construction Projects: A Conceptual Framework, Abdulrahman I. Iro, Juma M. Matindana, Julian Ijumulana

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Interim Payment Valuation is a critical process in road construction contract administration, yet conventional valuation practices remain heavily dependent on manual measurements, fragmented documentation, spreadsheets, and professional judgement. These limitations can affect measurement accuracy, transparency, traceability, and the timeliness of payment certification. Although Geographic Information Systems have increasingly been applied to construction planning, quantity measurement, progress monitoring, infrastructure management, and decision support, their integration with contractual and financial processes for interim payment valuation remains insufficiently explored. This study therefore develops a conceptual framework for integrating GIS with Interim Payment Valuation in road construction projects. A PRISMA-guided structured literature review …

Voltage-Related Power Quality Issues And Impacts On Distribution Networks With Sensitive Loads - A Review, Godwin Elinazi Mnkeni, Jackson Justo, Aviti Thadei Mushi, Bakari M. M. Mwinyiwiwa

Tanzania Journal of Engineering and Technology (TJET)

Voltage disturbances are the most important power quality (PQ) complications that customers and power utilities face in this smart era. The growing adoption of sophisticated electronic equipment and integration of renewable energy sources (RES) into power grids has increased the susceptibility of power distribution networks (PDNs) to voltage sags, swells, interruptions, flicker, and voltage imbalance. These disturbances, mainly caused by upstream faults, switching operations, and RES integration, compromise voltage PQ and system reliability. Consequently, they accelerate equipment degradation, increase electronic waste (e-waste), raise reactive power demand and maintenance costs, increase power losses, and impose substantial economic losses on customers and …

Retraction Notice To "Hydrogen Recovery, Cleaning, Compression, Storage, Dispensing, Distribution System And End-Uses On The University Campus From Combined Heat, Hydrogen And Power System" [International Journal Of Hydrogen Energy 39 (2014) 647-653], Tarek A. Hamad, Abdulhakim A. Agll, Yousif M. Hamad, Sushrut Bapat, Mathew Thomas, Kevin B. Martin, John W. Sheffield

Engineering Management and Systems Engineering Faculty Research & Creative Works

This article has been retracted: please see Elsevier policy on Article Correction, Retraction and Removal (https://www.elsevier.com/about/policies-and-standards/article-withdrawal). This article has been retracted at the request of the Editor.

Thermal Monitoring Of Solidification In Molded Casting Of Drone Landing Leg, Sadettin Cem Altıparmak, Maher Zayed, Samuel Hawk, Mohamed Baddi, Jesus Degollado, Ahmed Bendaouia, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

This paper presents the design, fabrication, and thermal characterization of an acrylonitrile butadiene styrene (ABS) mold produced by fused deposition modeling (FDM) extrusion-based additive manufacturing used for the wax casting of a drone landing leg. A thermal monitoring framework, consisting of four K-type thermocouples logged at 1 s intervals, was deployed across six casting trials to capture the complete solidification cycle, yielding 84,717 time-stamped measurements. The study focuses on thermal data analysis and materials science interpretation through descriptive statistics, normality diagnostics, inter-trial Kruskal–Wallis tests, phase-duration analysis, rolling-variance monitoring, and inter-channel Pearson correlation. Key findings include a persistent spatial temperature hierarchy …

Determination Of The Content Of Water-Soluble Vitamins In The Composition Of Beet Beetroot Composition, Jasur Esirgapovich Safarov, Shakhnoza Abduvaxitovna Sultanova, Muhammad Rasul Oglu Najafli, Doston Ishmuhammat Ugli Samandarov

Chemical Technology, Control and Management

The aim of this study was to determine the content of water-soluble vitamins in various parts of beetroot (pulp, leaves and stems) that had been subjected to various drying methods in a bid to explore the effect of physical processes, i.e., the application of ultrasound, on micronutrient preservation. The experiments were performed at the Department of Service Technologies of Tashkent State Technical University, and chromatographic analysis was performed in the Institute of Bioorganic Chemistry of the Academy of Sciences of the Republic of Uzbekistan. Chromatography was performed on Agilent-1200 chromatograph with Exlipse XDB C18 column and diode array detector using …

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Optimization Of Gas Consumption, Cost And Production Rate For Computerized Numerical Control Oxy-Acetylene Flame Cutters, Eustace K. William, Simon I. Marandu, Enock W. Nshama

Tanzania Journal of Science

This study examined the impact of flame cutting parameters (i.e., cutting speed, plate thickness and nozzle diameter) on oxy-acetylene gas consumption, cost and production rate. A full factorial design of experiments was used to generate 27 experiments, which were conducted using a CNC flame cutter. The analysis of variance (ANOVA) method was used to determine significant process parameters, followed by regression analysis using the MINITAB ® software. The technique for order preference by similarity to ideal solutions (TOPSIS) was used to determine the optimal cutting parameters for minimizing the consumption and cost estimation of oxy- acetylene gas and maximizing the …

Selfish Herd: Emergence Of Distributed Sensing, Timothy Mascal

Discovery Day - Daytona Beach

The problem of multi-agent swarm formation control seeks decision frameworks that exhibit desirable emergent behavior, including distributed sensing and communication, while remaining resilient to environmental noise. Previous work has demonstrated that the Selfish Herd Model is not only resilient to simulated sensor noise but performs better in its presence. This work further investigates the emergent behaviors of the Selfish Herd Model, particularly distributed sensing, by investigating whether the swarm achieves global stability equivalent to that observed in previous work utilizing global knowledge. A parameter variation study was performed across varying agent visual range and maximum neighbor count inputs to simulate …

Innovative Controls For Combustible Particulate Dust In Industrial Refineries, Sadie Dickman

Discovery Day - Daytona Beach

This project entails an extensive analysis of the occupational combustible dust hazard that exists in industrial refineries, including food processing, manufacturing, and metalworking facilities. Based on prior accidents like the 2008 Imperial Sugar and 2017 Didion Milling explosions, combustible dust causes fire and explosion risks that can result in damages, injuries, and fatalities. Through comparison of OSHA regulations, NFPA standards, and accident data, a lack of effective standards regarding training, audits, ventilation, fire prevention, and adequate housekeeping measures were highlighted to be an existing safety gap. The purpose of this study is to propose administrative controls to mandate companies to …

Investigating The Impacts Of Information Framing And Representation On Multi-Stakeholder Decision-Making For Tradespace Exploration, Meredith G. Sutton

All Dissertations

Tradespace exploration (TSE) is a decision-making process used in engineering design to search through a tradespace, containing all potential solutions to a design problem and their performance evaluations, in order to select optimal or near-optimal solutions. Solution optimality is driven by a desire to maximize the overall utility of a solution, which often cannot be done without making tradeoffs or compromises. The TSE process requires vast amounts of information which can be difficult to generate and understand, often leading to challenges including information overload, delays in decision-making, and suboptimal decisions, even for the most experienced designers. To address the challenges …

A Hybrid Machine Learning-Based Feasibility Prediction Of 3d Mechanical Designs Using Scalar And Geometric Features, Md Mohsin Uddin Fahim

Open Access Theses & Dissertations

The computational bottleneck of structural feasibility screening frequently hinders the transition from a digital 3D model to a physically manufactured component. Traditionally, engineers have relied on either overly rigid heuristic constraint checks or computationally exhaustive finite element simulations. To address this inefficiency, this thesis proposes and validates a hybrid machine-learning framework to predict the structural manufacturability of 3D mechanical designs. Moving beyond the conventional reliance on isolated scalar parameters, the proposed methodology extracts and integrates both scalar manufacturing constraints (e.g., tolerance, minimum feature thickness) and spatial geometric descriptors (e.g., bounding volume, aspect ratio) directly from STL mesh data. Utilizing a …

Prediction Of Satellite Temperature During An Orbit Of A Cubesat, Michael Reynolds

Honors Theses

This thesis develops a thermal-simulation strategy for predicting CubeSat component temperatures, applied to Jag-Sat-1, a CubeSat developed at the University of South Alabama and deployed from the International Space Station in 2022. The orbit was reconstructed from two-line element (TLE) data using simplified general perturbations (SGP4) propagation, and spacecraft attitude was recovered from onboard gyroscope measurements. Sunlight, penumbra, and umbra intervals were computed geometrically, and the external radiative environment — direct solar, Earth infrared, and albedo heat fluxes — was modeled using orientation-dependent view factors. These time-varying fluxes drove a transient finite-element thermal simulation of the full satellite geometry in …

Load Flow And Fault Performance Evaluation Of Interconnected Minigrids In Uganda Using Digsilent Powerfactory, Prossy Mutesi, Santos Kihwele, Emmanuel Matee

Tanzania Journal of Engineering and Technology (TJET)

The increasing demand for decentralized, reliable electricity in rural Sub-Saharan Africa has catalyzed the deployment of minigrids as an intermediate electrification strategy. This study investigates two solar photovoltaic (PV) mini-grids: Kyamugarura and Kanyegaramire, located in western Uganda, approximately 3km apart. Each mini grid initially consisted of 13 kW installed photovoltaic (PV) capacity, supplying power to households and small businesses. Due to rising demand and regular evening blackouts, both mini-grids are being upgraded to 57 kWp each. The integration of these upgraded systems into the national utility grid is proposed and simulated to evaluate performance improvements under two medium-voltage interconnection options: …

A Novel Hexagonal-Zigzag Cellular Infill Structure For Additive Manufacturing, Md. Saidur R Roney, Amm Nazmul Ahsan, Prosenjit Barua

Manufacturing & Industrial Engineering Faculty Publications

The rigidity of the Additively Manufactured objects can be tailored by manipulating the infill lattice type and density. In this research, an island type novel infill structure termed as Hexagonal-Zigzag pattern is introduced, and its mechanical performance is investigated. In this pattern, the zigzag raster reflects the repeating hexagonal shaped cell constituting the parallel-oriented islands and 90° rotation of the pattern in each layer distributes the island span along both transverse and longitudinal directions of the printing contour. A mathematical model is established to illustrate the effect of the infill parameters on hexagon unit cell size and relative infill density. …

Investigation Of Process Parameters To Fabricate Tiwmo Refractory Medium Entropy Alloy Via Laser Powder Bed Fusion, Abdullah Al Masum Jabir, Lindsey A. Salazar, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

This paper presents an experimental study on the fabrication of a TiWMo refractory medium-entropy alloy (RMEA) using laser powder bed fusion (PBF-LB/M, commonly known as selective laser melting) from elemental powders as well as successful alloy formation on titanium substrates. The effects of tungsten particle size and process parameters on successful TiWMo RMEA fabrication have been explored using scanning electron microscopy (SEM), x-ray diffraction, hardness measurement and microstructural analysis. Scanning electron microscope (SEM) analysis revealed that the lowest percentage (0.01%) of unmelted tungsten particles was observed at a laser power of 350 W and scanning speed of 250 mm/s, particularly …

Data Driven Estimation Of Pore Size Using 1d Light Emissions For Laser Powder Bed Fusion Additive Manufacturing, Jose Galarza, Jorge Barron, Luis Jimenez, Tamer Oraby, Jianzhi Li, Farid Ahmed

Manufacturing & Industrial Engineering Faculty Publications

The quality assurance of the Laser Powder Bed Fusion Process (LPBF) has been extensively investigated over the last decade for in-situ monitoring of metal additive manufacturing. The process inherently generates voids within the bulk of the part, which can detrimentally affect the quality of the printed part. The characterization of these voids by estimating their size and identifying their geometrical features remains a challenge. This study introduces a Machine Learning (ML) based framework for estimating void sizes of varying geometries using layer-wise one-dimensional (1D) average light intensity signal obtained from the optical tomography system during the 3D printing of metallic …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Development Of A Putting Green Manufacturing Process, Tabitha R. Webster

Honors Theses

Our Capstone project investigates the end to end design, development, and production of a 6‑foot long portable putting green marketed for individuals seeking a high quality, competitively priced golf product for home or office use. The capstone project examines the full lifecycle of product creation applying manufacturing principles learned through the center of manufacturing’s coursework. From the initial concept through engineering design, market research, prototyping, manufacturing optimization, and final production the project emphasizes cross‑functional collaboration across engineering, business, and accountancy majors. Methods used to gather data included marketing surveys, CAD drawings, time studies during production runs, value stream mapping, and …

Development Of A Putting Green Manufacturing Process, Jose Andres Cepeda Santiago

Honors Theses

Our Capstone project investigates the end-to-end design, development, and production of a 6‑foot long portable putting green marketed for individuals seeking a high quality, competitively priced golf product for home or office use. The capstone project examines the full lifecycle of product creation applying manufacturing principles learned through the center of manufacturing’s coursework. From the initial concept through engineering design, market research, prototyping, manufacturing optimization, and final production the project emphasizes cross‑functional collaboration across engineering, business, and accountancy majors. Methods used to gather data included marketing surveys, CAD drawings, time studies during production runs, value stream mapping, and controlled documentation …

The Optimization Of A Robotic Welding Arm To Improve Efficiency, Margaret Close

Honors Theses

The main objective of this report is to optimize a robotic welding arm to improve a locker manufacturing process. The robotic welding arm, a Miller PerformArc, used by Lockers Manufacturing has been producing spatter. Spatter significantly reduces the quality of the product and increases the product’s manufacturing time. The goal of this project was to find the best solution to reduce spatter without weakening the welds and ensuring that efficiency will increase. The first step in this project was to test multiple weld testing variables such as voltage, current, welding angle, robot speed, and arc and crater ratios. For each …

Engineering Design And Analysis Using Creo® Cad, Cae, And Manufacturing Applications, Swapnil Moon

Open and Affordable Textbooks

This textbook presents a structured approach to computer-aided design using Creo, integrating CAD, CAE, and CAM workflows within a unified engineering framework. The material emphasizes parametric modeling, design intent, and feature-based modeling as foundations for creating robust and adaptable engineering models. Through progressively structured tutorials, students develop skills in part modeling, assemblies, engineering drawings, mechanism design, simulation, and manufacturing. The text incorporates real-world engineering components and workflows, including structural and thermal analysis, motion simulation, and toolpath generation, reflecting modern engineering practice. Designed for upper-division undergraduate and graduate students, this open educational resource supports hands-on learning and prepares students for industry-relevant …

Introduction To Computer-Aided Design Using Solidworks® : A Structured Approach To Parametric Modeling And Design Intent, Swapnil Moon

Open and Affordable Textbooks

This textbook introduces computer-aided design (CAD) using SOLIDWORKS® through a structured, design-centered approach that emphasizes parametric modeling and engineering reasoning. Rather than focusing solely on software commands, the material develops foundational skills in design intent, constraint-based modeling, and feature relationships to create robust, adaptable models.

The content is organized progressively, beginning with basic sketching and feature creation and advancing to complex part modeling, assemblies, motion studies, and engineering drawings. Each chapter builds upon prior concepts, reinforcing systematic modeling practices and promoting the development of system-level thinking required in real-world engineering design workflows.

Designed for undergraduate students with little or no …

The Expectation Of Pain: Effects On Threshold, Tolerance, And Perception, Emma Paulus

Mechanical Engineering Undergraduate Honors Theses

Brain activity in pain-related regions of the cortex is thought to be influenced by interactions between expectations and incoming sensory information. However, the subjective experience of pain based on expectation has not been thoroughly explored. By changing visual and auditory cues to set expectation levels, a relationship between unconscious expectation of pain and actual sensory pain experienced was characterized. With IRB approval, volunteers were randomly and blindly grouped into low and high pain expectancy groups. Each group completed a survey about initial pain expectations before the muscle stimulation tolerance test, followed by a survey about actual pain perception after the …

Manufacturing Systems: Characteristics And Dynamics, Alan J. Fitzmorris

Graduate Theses and Dissertations (2019 - present)

This research answers three basic questions. First, what are the behaviors (dynamics) of a manufacturing system in the context of system performance? Are these dynamics best described as linear deterministic, periodic, nonlinear deterministic, or stochastic? Second, what are the complexity (chaotic) characteristics of a manufacturing system, namely the maximal Lyapunov exponent, correlation dimension, and Kolmogorov-Sinai entropy? Third, is there a relationship between complexity characteristics and manufacturing system performance? This research involves four high level steps: data analysis, system dynamics analysis, system complexity analysis, and correlation analysis. The data analyzed consists of concrete plant and shipbuilding shop time series performance data. …

Technology Based Assessment Of Workplace Biomechanical Risk: A Roadmap For Process Improvement, Tamer Adel Mohamed, Noha Mostafa, Ahmed Elsayed

Mechanical Engineering

The main objective of this paper is to develop a methodology for assessing the biomechanical risk in the workplace and design and apply improvements to reduce this risk by redesigning the working process. The risks are measured using Ergonomics tools to assess body posture and lifting index. Kinect sensor and video recordings are utilized to evaluate the joints' positions as an input for body posture data. Then, the specialized CATIA V5 software [26] is used to simulate the workers' bodies in the form of 3D models. Risk factors were assessed, and a new design was developed to be implemented in …