Nanoscience and Nanotechnology Commons^™

Metal-Free Nitrogen-Enriched Graphitic Carbon Nitride Architectures For Advanced Supercapacitor Energy Storage: Design, Synthesis, And Electrochemical Performance Optimization, Loujain Gamal Mohamed

Theses and Dissertations

Abstract

This thesis addresses the urgent global requirement for efficient energy storage materials by developing and characterizing advanced graphitic carbon nitride (g-C3N4)-based electrode materials for supercapacitors. A facile, low-cost thermal polymerization method produces 2D nitrogen-rich GCN nanosheets exhibiting excellent electrochemical stability and wide voltage windows, enabling symmetric devices with 19.33 Wh/kg energy density and remarkable cycling stability over 21,000 cycles. To overcome intrinsic limitations of pristine GCN, a 3D/2D metal free composite with bio-derived carbon (Bio-Cx) is synthesized, delivering high capacitance, wide potential windows, and ultrahigh energy density of 53.72 Wh/kg in asymmetric configurations paired with mesoporous nitrogen-doped carbon (MPNDC). …

Nanomagnet Based Reservoir Computing And Quantum Control, Fahim F. Chowdhury

Theses and Dissertations

Conventional CMOS scaling has driven remarkable advances in computing but faces increasing physical and energy constraints, motivating alternative computing paradigms that integrate memory and computation while improving energy efficiency. Nanoscale magnetic systems offer a promising platform for such approaches because their intrinsic nonlinear dynamics and localized magnetic fields can support both classical and quantum information processing. This thesis investigates nanomagnetic systems for physical reservoir computing and, with primary emphasis, for localized quantum control of spin qubits.

The first part explores dipole-coupled nanomagnet arrays as physical reservoirs. Micromagnetic simulations demonstrate nonlinear dynamical behavior with high short-term memory and parity-check capacity, enabling …

Hafnium Oxide-Based Nanoheterostructures For Catalytic Radiosensitization And Enhanced X-Ray Radiotherapy, Marlen Dariela Calix Quezada

Theses and Dissertations

Orthovoltage X-ray beams are attractive for surface and intra-operative radiotherapy. Yet, their clinical utility is constrained by rapid attenuation and the limited dose that can be delivered without harming healthy tissue. High-Z hafnium oxide (HfO₂) nanoparticles can boost local energy deposition through the photoelectric effect, while catalytic surface defects accelerate water radiolysis. Harnessing both mechanisms in a single nano-heterostructure could enable potent radiosensitization at diagnostic-range energies.

This thesis develops and evaluates HfO₂-based nanoheterostructures, both bare and Au-decorated, as catalytic radiosensitizers.

Two types of HfO₂ were evaluated, one was synthesized following a specific route and the …

Fabrication And Charcaterization Of Pullulan-Collagen Nanofibers Via Forcespinning, Valeria Leon Leal

Theses and Dissertations

Extensive research on collagen has spurred advancements in tissue engineering and biomaterial development, given collagen´s pivotal role in regulating various tissue structures across diverse organisms. This study delves into fabricating nanocomposites utilizing collagen, along with silver nanoparticles, chondroitin sulfate and pullulan, for potential applications in antibacterial medical devices, and cell regeneration. Collagen, abundant in the extracellular matrix, provides essential structural support, while silver nanoparticles and chondroitin confer antimicrobial properties, crucial for combating infections. Pullulan, a polysaccharide polymer, serves as a biocompatible carrier for silver nanoparticles whilst being the starting nanofiber forming material. Utilizing Forcespinning® technology, composite nanofibers were successfully synthesized. …

Validation, Optimization, And Experimentation Of Electro-Centrifugal Spinning, Carlos Alberto Delgado

Theses and Dissertations

The aim of this study is to understand the behavior of polymeric solutions, when exposed to both electric fields and centrifugal forces through the electro-centrifugal fiber creation method, observing both effects of various parameter variations on the resulting nanofibers. The elemental deposition on electrospun fibers through in-situ processes is studied and optimized. The morphology, crystallinity, thermal properties, and elemental composition of the nanofibers were characterized. The purpose of these nanofibers is for future applications such as energy harvesting, filtration, and biomedical applications.

Attachment Of 2d Nanomaterials Onto 1d Nanofibers For Separation And Sensing Applications, Elmmer A. Vera Alvarado

Theses and Dissertations

Advancing materials for water desalination and sensing is essential for tackling global issues related to clean water and efficient energy systems. This thesis explores the application of 2D nanomaterials, specifically graphene, integrated onto 1D poly(vinylidene fluoride) (PVDF) nanofibers to enhance their effectiveness in these areas. Utilizing innovative techniques such as Forcespinning® and plasma treatment, PVDF nanofibers were strengthened with graphene and conductive polymers like poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT: PSS). The research involved thorough assessments using direct contact membrane distillation (DCMD) systems, oil-water separation tests, and various mechanical and electromechanical evaluations. Heat-pressed membranes consistently delivered a flux of 0.33 kg/m²/hr and …

Enhancement Of Polytetrafluoroethylene-Polyvinyl Alcohol Nanofibers Triboelectric Effect With Carboxylic Functionalized Multiwalled Carbon Nanotubes Coating, Fernando Viesca

Theses and Dissertations

In this study, we fabricated a TENG using Forcespinning® (FS) Polytetrafluoroethylene microfibers (FS-PTFE-MFs) and Electrospun (ES) Polyvinyl alcohol nanofibers (ES-PVA-NFs). The FS-PTFE-MFs were physically linked with functionalized carboxylic multiwall carbon nanotubes (MWCNTs-COOH) employing water dispersions. MWCNTs-COOH were dispersed using three different surfactants: Sodium Dodecyl Sulfate (SDS), Sodium dodecylbenzenesulfonate (SDBS), and Triton X-100 (TX-100). Coated FS-PTFE-MFs were then characterized using a field emission scanning electron microscope (FESEM) with an energy dispersive X-ray spectroscopy (EDS) attachment and Fourier-transform infrared spectroscopy (FTIR). While no significant difference in performance was observed with different surfactants, electrical results of the TENG recorded a notable enhancement of …

Activity Descriptors As Tools For Designing Highly Efficient Electrocatalysts For Water Splitting, Aya Gomaa

Theses and Dissertations

There is an uprising urge to design efficient, active, and durable catalysts to achieve sustainable hydrogen production. The unambiguity of which material should be used pushed the scientific community to devote enormous efforts in exploring different elements with different ratios on trial and error bases. However, the bridge between the theoretical calculation and the experiments introduced a new realm of designing efficient catalysts by introducing the concept of activity descriptors. In the first part of the thesis, the ability to convert waste stainless steel (SS) 316L meshes into highly efficient and durable oxygen evolution reaction (OER) catalysts is demonstrated. The …

The Effect Of Mechanical Strain On The Electronic Conductivity Of Α- Fe2o3: A Density Functional Theory Study, Sheriff Naziru Abdulmutalib

Theses and Dissertations

Hydrogen has emerged as a promising future energy carrier due to its ability to produce zero carbon dioxide (CO2) emissions when burned. However, the limited natural abundance of hydrogen necessitates the development of cost-effective and environmentally friendly methods for large-scale hydrogen production. Among the different hydrogen production approaches, photoelectrochemical water splitting, which employs a photoanode material in a cell using solar energy to split water into hydrogen and oxygen, is the focus of this work. α-Fe2O3 (hematite) is a photoanode material that shows a promising future for hydrogen generation in a photoelectrochemical cells due to its cheapness, availability, and its …

Mechanical And Electromagnetic Properties Of Incorporating Graphene Oxide In Cementitious Mixtures, Cherif Khalil

Theses and Dissertations

This multidisciplinary study aimed at investigating the impact of incorporating graphene oxide (GO) on the mechanical properties and electromagnetic (EM) shielding effectiveness of cementitious mixtures, as well as critically examining the mechanism with which GO affects their microstructure properties. Analysis of the literature review showed that there are discrepancies in reporting the impact of GO on the mortar mix. Consequently, this study focuses on exploring the cause for such discrepancies and identifies three main factors which are thoroughly investigated. The factors were the different sonication energies applied to the GO (Shear Mixing, 1.5 kJ/ml, 3 kJ/ml and 6 kJ/ml), the …

Bridging The Gap In Epsilon-Near-Zero Nonlinear Materials, Adam R. Ball

Theses and Dissertations

Studying how light and matter interact has been of interest to humans for thousands of years. From the invention of the first mirror, burning ants with a magnifying glass, to optical fiber communication, light has been central to mankind. Researchers have sought to take this to the extreme with nonlinear optics where intense laser light interacts with materials. The study of this thesis is to understand a new generation of materials that has come to light. Epsilon-near-zero (ENZ) materials have shown promise for ultrafast light manipulation in tandem with modern day CMOS compatible electronics. Here, I seek to bridge the …

Two-Dimensional Nanomaterials And Nanocomposites For Sensing, Separation, And Energy Applications, Md Ashiqur Rahman

Theses and Dissertations

Two-dimension (2D) nanomaterials have gained popularity for the last few decades due to their excellent mechanical, electrical and thermal properties. These unique properties of 2D nanomaterials can be exploited in various applications specially in sensor, energy, and separation devices. In this study, the sensing and energy generation performance of PVDF/PAni fiber mat systems made by the forcespinning method with and without graphene coating. The graphene-coated nanocomposites show an average output voltage of 75 mV (peak-to-peak) which is 300% higher compared to bare fiber mats and an output current of 24 mA (peak-to-peak) by gentle finger pressing. Moreover, the graphene-coated PVDF/PAni …

From Waste To Energy: The Electrochemical Reduction Of Co2 Using Recycled Nanostructured Catalysts, Ibrahim Badawy

Theses and Dissertations

The reduction of carbon dioxide (CO₂RR) using electrochemistry is a promising solution for the burgeoning global energy crisis. The overall vision of its implementation relies on renewable energy sources to power the reaction creating carbon neutral products and effectively closing the carbon cycle. Research in this field has come a long way since its inception in the mid-1900s. However, there remain significant hurdles and important considerations to overcome in order to reach full commercialization. Most electrocatalysts tested for CO₂RR have been designed solely for maximum performance while ignoring the environmental consequences if such a material were …

Influence Of Dilute Silicon Carbide Nanoparticle Additions To The Microstructure And Mechanical Properties Of Laser Powder Bed Fusion Molybdenum, Nathan E. Ellsworth

Theses and Dissertations

Consolidation of pure molybdenum through laser powder bed fusion and other additive manufacturing techniques is complicated by a high melting temperature, thermal conductivity, and ductile-to-brittle transition temperatures. Nano-sized silicon carbide particles (0.1 wt%) were homogeneously mixed with molybdenum powder and the printing characteristics, chemical composition, microstructure, and mechanical properties were compared to pure molybdenum for scan speeds of 100, 200, 400, and 800 mm/s. The addition of silicon carbide improved the consolidation and mechanical properties and the oxygen content was reduced. Two mechanisms of oxygen reduction were identified as responsible for the improvements: oxidation of free carbon and the creation …

Mechanical Properties And Performance Of A Novel Nano-Engineered Unitized Composite With Quasi-Isotropic Layup, Brian Matthew Pudlo

Theses and Dissertations

Carbon nanotubes (CNTs) exhibit outstanding mechanical, electrical, and thermal properties, but are a challenge to effectively implement into macroscopic composites for aerospace applications. This research investigates the mechanical properties and performance of a newly developed hybrid NanoStitch composite, alongside a control polymer matrix composite, at room temperature. Both composite material systems investigated in this work have quasi-isotropic layup. Monotonic tension-tofailure, tension-tension fatigue, and creep tests were performed to characterize the performance of the composites under cyclic and sustained loading. Experimental results obtained for the quasi-isotropic NanoStitch composite were compared to those obtained for the quasi-isotropic control composite. The properties and …

Formulation Of Encapsulated Nanoparticles Of Leek Extract As Antimicrobial And Anticancer Agent, Rawan Hassan Mohamed Elghanam

Theses and Dissertations

Leek extract (LEK) has broad therapeutic activity. However, plant extract use has many drawbacks, which could be resolved using nanocarriers. The purpose of this research work was to prepare chitosan nanoparticles (CS NPs) encapsulating LEK and investigate their antioxidant, antimicrobial, and anticancer activity. Gas chromatography-mass spectroscopy was used to determine the LEK components. The CS-LEK NPs were produced by tripolyphosphate (TPP) crosslinking with chitosan (CS) the ionic gelation methodology. The particle size was 331 nm, zeta potential (ZP) was 28.9 mv, polydispersity index (PDI) was 0.4, encapsulation efficiency (EE) was 65.6%, and loading capacity (LC) was 28.8 % of the …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

Novel Development Of A Low-Cost, Micrometer-Scale Tip-Enhanced Raman Spectroscopy System, John Yates

Theses and Dissertations

Modern scientific instruments are significant capital investments for universities. These investments can be outside of the funding capabilities of some smaller universities or departments and can be a significant barrier in the pursuit of scientific breakthroughs. This project aims to provide a template for universities or research groups to upgrade, at a reasonable price, an existing Raman spectroscopy system to a Tip-Enhanced Raman Spectroscopy (TERS) system. This system can serve as a permanent upgrade to an existing system or as a bridge necessary to prove the viability of a research path before significant capital investment in a commercial TERS system. …

Biomimetic Strategies To Control Therapeutic Release From Novel Dna Nanoparticles, Robert J. Mosley

Theses and Dissertations

The inherent chemical, mechanical, and structural properties of nucleic acids make them ideal candidates for the formulation of tunable, personalized drug nanocarriers. However, none so far have exploited these properties for the controlled release of therapeutic drugs. In this dissertation, a biomimetic approach to controlling drug release is exhibited by specifically manipulating the architecture of novel, DNA nanoparticles to take advantage of drug binding mechanisms of action. Rationally designed DNA strands were immobilized on gold surfaces via a terminal thiol modification. Immobilized monomers can be manipulated to form distinct monolayer architectures including flat, folded, coiled, or stretched structures. Increasing the …

Photocatalytic Degradation Of Organic Contaminants By Titania Particles Produced By Flame Spray Pyrolysis, Noah Babik

Theses and Dissertations

Advanced oxidation of organic pollutants with TiO2 photocatalysts is limited due to the wide bandgap of TiO2, 3.2 eV, which requires ultraviolet (UV) radiation. When nanosized TiO2 is modified by carbon doping, charge recombination is inhibited and the bandgap is narrowed, allowing for efficient photodegradation under visible light. Here, we propose a flame spray pyrolysis (FSP) technique to create TiO2. The facile process of FSP has been successful in preparing highly crystalline TiO2 nanoparticles. Using the same procedure to deposit TiO2 onto biochar, the photocatalyst was doped by the carbonaceous material. The morphology, crystalline and electronic structure of the FSP …

Branched Chain Amino Acid Strain State Monitoring With Raman Spectroscopy And Plasmonic Bowtie Nanoantenna Devices For Early Disease Detection, Caroline A. Campbell

Theses and Dissertations

This work centers on the development and the down-selection of nano-manufactured devices to be used in conjunction with Raman spectroscopy for probing a branched chain amino acid. The nano-manufactured devices integrate plasmonic nanoantennas for the purpose of amplifying molecular fingerprints, which are otherwise difficult to detect, through Surface Enhanced Raman Spectroscopy (SERS). Plasmonic nanostructures can be utilized for a variety of biomedical and biochemical applications to detect the characteristic fingerprint provided by Raman Spectroscopy. The nano-manufactured devices create an electric field that amplifies minute perturbations and raises the signal above background noise. This may provide a deeper understanding of signal …

Exploration Of Antimicrobial And Cell Proliferation Properties Of Nanofibers Incorporating Nopal (O. Cochenillifera) Extract, Cristobal Rodriguez

Theses and Dissertations

This study focused on the fabrication of Forcespinning® nanofibers composed of Opuntia cochenillifera, ‘nopal’, mucilage (N) extract, chitosan (CH), and pullulan (PL) (N/CH/PL) were developed with an optimum fiber average diameter of 406±127 nm, and studied for their ability to sustain adhesion and proliferation of mouse embryonic fibroblast (NIH 3T3) cells. After a 6-day incubation period, N/CH/PL nanofibers displayed robust cell proliferation, while also exhibiting inhibitory properties through an N extract dip-coating process against gram-negative bacteria Escherichia coli in a 24 h bacterial growth study. A demonstration of integrated natural bioactive compounds with combined biodegradable polymers, provide an enhanced …

Error Reduction For The Determination Of Transverse Moduli Of Single-Strand Carbon Fibers Via Atomic Force Microscopy, Joshua D. Frey

Theses and Dissertations

The transverse modulus of single strand carbon fibers is measured using PeakForce Atomic Force Microscopy - Quantitative Nanomechanical Measurement to less than 5 percent error for 11 types of carbon fiber with longitudinal moduli between 924-231 GPA, including export-controlled fibers. Statistical methods are employed to improve the quality of data to exclude outliers within an measurement and within the sample set. A positive linear correlation between the longitudinal and transverse modulus with an R²=0.76 is found. Pitch-based fibers exhibit lower measurement error than PAN-based fibers, while PAN fibers exhibited no apparent modulus correlation when the Pitch fibers are …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Laser Induced Thermal Degradation Of Carbon Fiber-Carbon Nanotube Hybrid Laminates, Joshua A. Key

Theses and Dissertations

Recent advancements in fiber laser technology have increased interest in target material interactions and the development of thermal protection layers for tactical laser defense. A significant material of interest is carbon fiber reinforced polymers due to their increased use in aircraft construction. In this work, the thermal response of carbon fiber-carbon nanotube (CNT) hybrid composites exposed to average irradiances of 0.87-6.8 W/cm² were observed using a FLIR sc6900 thermal camera. The camera had a pixel resolution of 640x512 which resulted in a spatial resolution of 0.394x0.383 mm/pixel for the front and 0.463x0.491 mm/pixel for the back. The hybrid samples …

Mechanical And Structural Behavior Of As-Built And Post Treated Ti6al4v Lattice Structures Fabricated By Selective Laser Melting (Slm), Hala Ahmed Salem

Theses and Dissertations

Lattice structure is a type of cellular structures that is composed of repeatable unit cells, each of which is formed of interconnect network of struts. Lattices with different structures are gaining attention for their good mechanical properties for light weight applications. Selective laser melting (SLM), is one of the AM powder-bed fusion fabrication techniques. SLM is widely known for its capability for fabricating complex metallic structures such as lattice structures with high resolution. SLM process influence the microstructure and mechanical properties of fabricated parts. The used processing parameters influence the level of internal porosity within the fabricated parts which directly …

Electric Field Control Of Fixed Magnetic Skyrmions For Energy Efficient Nanomagnetic Memory, Dhritiman Bhattacharya

Theses and Dissertations

To meet the ever-growing demand of faster and smaller computers, increasing number of transistors are needed in the same chip area. Unfortunately, Silicon based transistors have almost reached their miniaturization limits mainly due to excessive heat generation. Nanomagnetic devices are one of the most promising alternatives of CMOS. In nanomagnetic devices, electron spin, instead of charge, is the information carrier. Hence, these devices are non-volatile: information can be stored in these devices without needing any external power which could enable computing architectures beyond traditional von-Neumann computing. Additionally, these devices are also expected to be more energy efficient than CMOS devices …

Formulation And Validation Of Nanoparticle Controlled Delivery For Chemotherapeutic Drug Products, Shani L. Levit

Theses and Dissertations

Taxol, a formulation of paclitaxel (PTX), is one of the most widely used anticancer drugs, particularly for treating recurring ovarian carcinomas following surgery. Clinically, PTX is used in combination with other drugs such as lapatinib (LAP) to increase treatment efficacy. Delivering drug combinations with nanoparticles has the potential to improve chemotherapy outcomes. In this study, we use Flash NanoPrecipitation, a rapid, scalable process to encapsulate weakly hydrophobic drugs (logP in vitro. Encapsulating either PTX or LAP into nanoparticles increases drug potency. When PTX and LAP are co-loaded in the same nanoparticle, they have a synergistic effect that is greater than …