Tribology Commons^™

The Effect Of Mwcnt-Oil Impregnation Of Sintered Components On Their Wear And Corrosion Resistance, Maha Khaled Abdelfadeel

Theses and Dissertations

Powder Metallurgy (PM) offers an advantageous route for manufacturing complex and near net-shape components. Their inherent interconnected porosity that promotes the action of self lubrication compromises their structural integrity by creating pathways for corrosion and excessive wear. This research investigates the efficacy of Multi-Walled Carbon Nanotubes (MWCNTs) as a nano additive within the impregnating base oil (SN-150 base oil). An experimental matrix was designed to evaluate the influence of MWCNTs with different concentrations of 0.05, 0.1, and 0.2 wt.% and ultrasonic dispersion with varying sonication times of 30 and 60 minutes on the tribological and electrochemical performance of sintered steel …

Design New Stage For Vacuum Pin On Disk, Miranda Boyd

Williams Honors College, Honors Research Projects

For my senior design project, I am redesigning the moving stage for the vacuum pin-on-disk test used in the Akron Engineering Tribology Lab. This system is used to evaluate bearings and lubricants for aerospace applications under controlled vacuum conditions. The current stage design limits flexibility when adjusting for different testing parameters, so my goal is to develop a new movable stage that allows for varying weights and loads to be applied accurately and safely. The redesigned stage will improve test efficiency, adaptability, and precision, ensuring the system can accommodate a wider range of experimental conditions and materials while maintaining compatibility …

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Fourier Analyses Of Optical Profilometry As An Inferential Measurement For Impact Coverage., Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A critical consideration in peening process design is achieving sufficient impact coverage. Conventional methods for assessing coverage rely on manual inspection, which is time-consuming and poorly suited for automated control. In this work, we investigate the use of frequency-domain analysis to quantify surface modification in peened samples using optical profilometry (OP) data. Three-dimensional surface maps of Almen strips were acquired using a high-resolution OP system and analyzed via fast Fourier transform (FFT) to compute spatial power spectral densities (PSDs). PSD maps and radially averaged profiles reveal consistent amplification of harmonic components similar to the nominal particle size, with increasing intensity …

Wear Of High Entropy Alloys: Understanding Effects Of Cryogenic Temperatures And Surface Nitriding On Wear Behavior, Aubrey Yu Tang

Dartmouth College Ph.D Dissertations

Cryogenic tribological applications have become increasingly important with the development and innovation of advanced equipment in aerospace, polar regions, superconductivity, and more. Traditional lubrication methods are not viable under these harsh environments, so metallic materials must be able to maintain excellent mechanical properties and withstand the constant impact and wear alone. High entropy alloys (HEAs) have emerged as potential candidates for these applications because of their wide variety of excellent room temperature properties and apparent improvement of mechanical properties of some HEAs at extremely low temperatures. Despite their promising nature, very limited work has been done on understanding the wear …

Analysis Of Ptfe Radial Lip Seals For Wheel Bearing Applications, Madison Vogt

Theses and Dissertations--Mechanical and Aerospace Engineering

A numerical analysis was conducted to investigate the viscoelastic effects of nonlinear materials on the sealing zone and contact pressure distribution of radial lip seals in a conventional geometric topology. The use of nonlinear materials in radial lip seal applications is desirable to improve operation and reliability of rotating machinery due to their high operating temperatures, chemical compatibility, and low friction coefficients. Examples include, but are not limited to, seals within industrial air compressors, turbine engines, aircraft landing systems, chemical processing equipment, and Freon pumps. This work focuses on analyzing the nonlinear viscoelastic response of pure Polytetrafluoroethylene (PTFE) and PTFE …

Lifetime Prediction Of Pan Feeder Based On 3d Laser Scanning For Wear Assessment, Nony Maulidya, Dedi Priadi, D. Rizal Asral

Journal of Materials Exploration and Findings

Apron feeder is one of stages in crushing circuit to convey material in short distance. Pan flight is the main component of apron feeder that is severely exposed to wear mechanism due to its direct contact with open cut abrasive ore. With this operating environment of apron feeder, regular maintenance and inspection must be conducted to assess wear rate of pan’s surface to maintain equipment availability and provide information and sign before the equipment undergoes severe and sudden degradation. 3D laser scanning is method used in this study as Non-Destructive Testing (NDT) based inspection. The aim of using 3D scanning …

Understanding The Microstructure And Tribological Performance Of Cocrfeni-Based High Entropy Alloys, Ali Azarmi

All Theses

Due to their higher wear resistance compared to conventional alloys, high entropy alloys (HEAs) are now being considered as candidates for parts undergoing sliding contact during their lifetimes. While the engineering field has built some knowledge related to the performance of selected high entropy alloys, such as the CoCrFeNi alloy, more research is needed to determine if (how) expansions from four to five principal alloying elements alter the performance compared to the initial alloy. In this study, we started this research effort by investigating the relative performance of CoCrFeNiMn and CoCrFeNiTi with respect to CoCrFeNi. The two primary alloying elements …

Synthesis Of Ni-Based Intermetallics By Electrolytic Plasma Processing Of Ti And Ti-Based Alloys, Chuzhong Zhang

Material Science and Engineering Dissertations - Archive

EPP is an innovative surface modification technique that enables the deposition of metal ions from the electrolyte and their integration with substrate atoms to form intermetallic compound surface layers. EPP offers advantages such as high deposition rates, environmental cleanliness, and operational simplicity. In this study, Ni-Ti intermetallic layers were successfully synthesized on a Ti-6Al-4V substrate using EPP. The properties of the resulting Ni-Ti intermetallic layers were characterized using SEM, EDS, XRD, TEM, nanoindentation, and tribology tests.

This work aims to understand the fabrication mechanism and investigate the effects of various processing parameters on the EPP process. Key factors such as …

Inherently Porous Metal Structures With Sufficient Mechanical Properties Through Direct Writing Of Bio-Based Inks, Havva Eda Aysal

Graduate Theses, Dissertations, and Problem Reports (ETD)

There is currently a burgeoning interest in developing 3D printed metal structures with inherent porosity and sufficient mechanical properties for mass customization in the biomedical field. Current approaches for 3D printing of biocompatible metals rely on powder-bed fusion methods which are energy intensive and utilize large amounts of metal powder that is challenging to recycle. In addition, such methods aim on producing dense parts and porosity generation, within the printed part, is challenging due to the complex physics of the melting pool. Here, a relatively new and promising approach is undertaken to study the 3D printing of inherently porous structures …

Extending Trailer, Alex Grove

Williams Honors College, Honors Research Projects

The goal of this research project is to revolutionize the convenience in towable transportation. This innovative design aims to enhance the versatility of pull-behind trailers by incorporating an extendable feature, allowing users to effortlessly adjust the length according to their specific needs. Whether navigating tight spaces or accommodating extra cargo, our trailer adapts to diverse situations, providing unmatched flexibility. In addition to its adjustable length, the trailer is engineered to be compactable, addressing the storage constraints often faced by users with limited space. The collapsible design ensures easy storage without compromising on functionality, making it an ideal solution for individuals …

Laser Deposition Additive Manufacturing Of Multi-Material And Metal-Ceramic Composite Structures, Manikanta Grandhi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing performance requirements of modern industrial systems, coupled with the imperative for decarbonization, necessitate a fundamental rethinking of metallic component design and manufacturing. Traditional materials, with their inherent limitations in property optimization, susceptibility to degradation, and weight constraints, are proving insufficient. Multi-material joining offers a potential solution, enabling designers to strategically integrate diverse materials with specific, tailored properties into single component. Functionally graded materials (FGMs) and oxide dispersion strengthened (ODS) materials are prime examples of this approach, delivering substantial improvements in wear resistance, thermal regulation, high-temperature resilience, and overall weight efficiency. However, conventional manufacturing approaches further exacerbate the limitations …

Molecular Dynamics Study Of Characterization In Metal-Free Friction Materials, Yizhan Zhang

Electronic Theses and Dissertations

Metallic friction materials currently used in industry may adversely impact the environment. Substitutions for metals in friction materials, on the other hand, can introduce operational safety issues and other unforeseeable issues such as thermal-mechanical instabilities and insufficient strength. In view of it, this dissertation focuses on developing different kinds of materials from simple structure to complex structure and evaluating the material properties with the assistance of molecular dynamics (MD) tools at the nano scale.

First, the concept of the contacted surfaces in friction at the atomic scale was introduced in order to get accurate understanding of the friction process compared …

Tribological Studies Of Thick Polytetrafluoroethylene Coatings Enhanced By Polydopamine And Nanoparticles, Sujan Kumar Ghosh

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a popular low friction solid lubricant with high chemical and thermal stability. Thick PTFE coatings have the potential for many tribological applications, such as replacing Tin-based Babbitt materials in journal bearings. However, the weak bonding strength to the substrate and the high wear rate of PTFE coatings are current limiting factors. The lack of understanding of their tribological properties and wear mechanisms in oil-lubricated conditions and how coating thickness affects the tribological performance further hindered the use of PTFE coatings. In this dissertation, polydopamine (PDA), a bio-inspired adhesive, is used as an underlayer for or as a …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Solid State Synthesis And Characterization Of Apatite Based Ceramic Waste Form For The Immobilization Of Radioactive Iodine, Md Imdadul Islam

LSU Doctoral Dissertations

The growing demand for nuclear power in the United States and worldwide is accountable for addressing the major concern of radioactive waste, involving the technical challenges of maintaining the nuclear fuel cycle and immobilizing high-level wastes for safe disposal in geological storage. The appropriate selection of waste forms for spent nuclear fuel such as fission products and radionuclides can be effective means for a feasible and sustainable nuclear fuel cycle. But highly volatile radionuclides such as iodine (129) are of specific concern due to its extraordinary long half-life (15.7 million years). Due to its poor solubility and high volatility at …

Viscoelasticity Of Ptfe-Based Face Seals, Bo Tan

Theses and Dissertations--Mechanical and Aerospace Engineering

PTFE-based materials are widely used in areas of tribology, particularly in seal and bearing applications because of their outstanding self-lubricating properties. Often in dynamic seal applications there is a need for ultra-low mechanical friction loss between the sealing surfaces. Due to its extremely low friction coefficient, there is interest in employing Polytetrafluoroethylene (PTFE) materials in such applications. One challenging aspect of employing PTFE is that these materials are viscoelastic and plastic. This dissertation concentrates on the modeling of viscoelastic material response when used as mechanical face seals with a focus on PTFE-based materials. First, the viscoelastic characteristics are measured through …

Pulse Reverse Current Electrodeposited Tio2 Doped Ni-W Coating, Sydney Hughes

Williams Honors College, Honors Research Projects

Nickel-Tungsten (Ni-W) coatings via the pulse reverse current method have been under development as a potential replacement for typical Chromium/Cadmium coatings. To increase the effectiveness of Ni-W as a coating, dopants have been tested to decrease microcracks and pores and increase overall tribological performance. Previous research by Timken Engineered Surfaces Laboratory showed that Ni-W doped with TiO₂ nanoparticles had a positive effect on coating performance. The purpose of this study was to determine the ideal solution parameters (i.e. TiO₂ concentration, pH) to maximize the benefit of the dopant when samples are subjected to tribological testing. Here, solutions of …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

Investigation Of The Tribological Behavior Of Mineral Lubricant Using Copper Oxide Nano Additives, Ahmed A. Abdel-Rehim, Sayed Akl, Sherif Elsoudy

Mechanical Engineering

In this study, tribological properties of custom formulated and stabilized nano lubricant are investigated. Spherical CuO nanoparticles are suspended in 20W-50 mineral base lubricant using Oleic Acid (OA) as a surfactant. Three different nano lubricant concentrations with 0.2, 0.5, and 1 wt.% were analyzed through ASTM G-99 pin-on-disc tribometer standardized test under boundary/mixed lubrication regimes. The generated friction and wear analyses confirm a consolidation of tribological properties with a reduction in friction coefficient in the range of 14.59–42.92%, compared with the base lubricant. Analysis of worn surfaces (SEM/EDX) as well as (AFM) was conducted. Combined hypotheses were proposed from the …

Mechanical And Frictional Behavior Of Textured And Non-Textured Surfaces, Raghuram R. Santhapuram

Graduate Theses and Dissertations

Tribology is the study of surfaces where two objects are sliding against another. Significant energy is lost due to friction between the sliding surfaces. Therefore, developing or designing surfaces to minimize friction is critical for the durability and reliability of the mechanical components. Several researchers have identified that surface texturing at the nanoscale (nanotexture) would reduce the friction between the contacting surfaces. The nanotextured surfaces have several applications in microelectromechanical systems and nanoelectromechanical systems. This dissertation employs molecular dynamics simulations to investigate the frictional and mechanical response of nanotextured aluminum (Al) and Al/amorphous silicon (a-Si) composite surfaces.

This study determines …

Effects Of Polytetrafluoroethylenemicro–Particles On Mechanical Andtribological Properties Of Glass Fiberreinforced Polyoxymethylene, Kunnan Singh Jasbir Singh

Student Works (2020-2029)

Reinforcing polyoxymethylene (POM) with glass fibers (GF) enhances its mechanical properties, but at the expense of tribological performance. Formation of a transfer film to facilitate tribo–contact is compromised due to the abrasiveness of GF. As a solid lubricant, for example, polytetrafluoroethylene (PTFE) significantly improves friction and wear resistance. The effects of chemically etched PTFE micro–particles on the fiber– matrix interface of POM/GF/PTFE composites have not been systematically characterized. This research investigated the effects of PTFE micro–particles on mechanical and tribological properties of POM/GF/PTFE composites. Since PTFE is immiscible with most polymers, the surface was etched using sodium naphthalene salt dissolved …

Investigation Of Chip-Form And Tool-Wear In Turning Of Hardened Af9628 Alloy Under Various Cooling And Lubrication Conditions, Jason Wolf

Theses and Dissertations--Manufacturing Systems Engineering

Next generation defense and commercial applications for structural steels require new alloys that eliminate or reduce critical elements from their composition to lower cost and improve manufacturability, while maintaining or exceeding high strength and toughness requirements. A new alloy, denoted as AF9628, has recently been developed for this purpose and its manufacturing characteristics and the material response in component manufacturing must be fully understood.

In the present study, hardened AF9628 alloy was turned with a coated carbide cutting tool under fixed cutting speed, feed rate, and depth of cut parameters. This work focuses on chip-form and tool-wear analysis to understand, …

Incorporation Of Silica Nanoparticles Into The Underlayer Of Pda/Ptfe Thin Coatings, Adedoyin Abe

Mechanical Engineering Undergraduate Honors Theses

Polytetrafluoroethylene (PTFE) is one of the most low friction and corrosion resistant solid lubricants. Prior studies have shown that a polydopamine (PDA) underlayer enhances the durability of PTFE thin coating. In this study, 100, 200, and 300 µL of aqueous silica nanoparticle (NP) solutions were added to the PDA deposition solution. The durability and coefficient of friction of PDA/PTFE thin coatings on stainless steel substrates are investigated with and without incorporating the silica NPs. The coatings were tested in dry contact conditions using a Universal Mechanical Tester (UMT) with a ball-on-flat configuration in a reciprocating motion. It was found that …

Understanding The Evolution Of Surface Texture Under Boundary Lubrication, Salil T. Bapat

Graduate Theses and Dissertations

The objective of this research was to understand the evolution of surface texture under boundary/mixed lubrication (BL). Significant material/energy losses occur during BL because of direct contact between the two surfaces. Traditionally, tribofilms have been studied extensively for BL while textures have been used as a static engineering design parameter to enhance lubricant film properties. However, texture is dynamic at the tribological mating interface, where both physical and chemical interactions are continuously modulated. The evolution and the interplay between the tribofilm and texture is least studied in the literature, which is the focus of this research.

MoS2-based lubricants, known for …

Triboelectric Solar Generator Concept And Experimental Research, Elias Yazdanshenas

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a novel concept, a triboelectric solar generator (TSG ), is proposed for generation of high voltage direct current (HVDC) electricity from solar radiation. An experimental investigation was conducted to prove the concepts of charge generation through the triboelectric effect and charge transmission using semiconductors. The triboelectric effect, also known as the contact electrification, is a well-known physical phenomenon that electrostatic charges are generated by rubbing dissimilar materials. However, traditional triboelectric generators had never been commercialized due to their poor power output. Physically, it is due to the difficulty of charge transmission from insulators, which generate charges. The …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Prediction Of Tribological Behavior Of Candidate Materials For Rotor Seals, John W. Franzino, Will F. Michul

Materials Engineering

To reduce high costs associated with manufacturing and testing materials for rotor seals, a procedure needs to be developed to quickly and accurately test candidate materials as they are released. The test should reduce the amount of fabrication required and model working conditions in order to accurately assess the tribological behavior of candidate materials. A possible solution was examined that utilized a rig meant to model operational stresses and wear. Compression modulus data was then taken in order to quantify the accumulation of damage due to microcracking, the primary mode of failure, through a damage index parameter. Testing results concluded …

Phase Transformation In Monolayer Molybdenum Disulphide With And Without Defects Under Tension Predicted By Atomistic Simulations, Khanh Quoc Dang

Graduate Theses and Dissertations

In addition to its use as a solid lubricant, molybdenum disulphide (MoS2) has gained recent attention as a possible substitute for silicon as it is increasingly difficult to keep shrinking down electronic devices made of silicon, the conventional electronic material. When thinned down to atomic thickness, monolayer MoS2 possesses very unique and promising electronic and electrical properties. Unlike electronic and electrical properties, knowledge of the mechanical properties and role of structural defects on these properties of monolayer MoS2 is unexplored. For this thesis, the two main objectives are (1) to gain insight about the failure mechanism of monolayer MoS2 by …

Fretting Fatigue Behavior Of A Titanium Alloy Ti-6al-4v At Elevated Temperature, Onder Sahan

Theses and Dissertations

The purpose of this research is to investigate the fretting fatigue behavior of the titanium alloy Ti-6Al-4V at elevated temperature is investigated. Fretting and plain fatigue experiments are conducted at 260 °C. Crack initiation location and crack initiation orientation is measured and fretting and plain fatigue life data of the specimens from these tests are obtained. Fatigue parameters capable of predicting the number of cycles to specimen failure, the crack location and the crack orientation along the contact surface are analyzed. The parameters are calculated by using the computed stresses and strains obtained from the finite element analysis. The mechanisms …