Manufacturing Commons^™

A Total Life Cycle Approach For Developing Predictive Design Methodologies To Optimize Product Performance, Buddhika M. Hapuwatte, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Sustainable products must be designed by considering how design decisions impact their total life cycle (TLC) sustainability content. Even more so important when designing products to incorporate the technological elements of sustainable manufacturing, the 6Rs (Reduce, Reuse, Recycle, Recover, Redesign and Remanufacture), to achieve Circular Economy (CE). This paper presents the preliminary work of an ongoing research project on developing a novel framework incorporating predictive models with TLC considerations. This unique approach develops and integrates models with associated risks, and optimizes for maximizing the sustainability benefits due to design decisions. Such predictive capability is extremely useful for process planning, where …

Process Sustainability Evaluation For Manufacturing Of A Component With The 6r Application, Ana E. Bonilla Hernández, Tao Lu, Tomas Beno, Claes Fredriksson, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Sustainability in manufacturing can be evaluated at product, process and system levels. The 6R methodology for sustainability enhancement in manufacturing processes includes: reduced use of materials, energy, water and other resources; reusing of products/components; recovery and recycling of materials/components; remanufacturing of products; and redesigning of products to utilize recovered materials/resources. Although manufacturing processes can be evaluated by their productivity, quality and cost, process sustainability assessment makes it a complete evaluation. This paper presents a 6R-based evaluation method for sustainable manufacturing in terms of specific metrics within six major metrics clusters: environmental impact, energy consumption, waste management, cost, resource utilization and …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

Investigation Of Chip-Form And Tool-Wear In Turning Of Hardened Af9628 Alloy Under Various Cooling And Lubrication Conditions, Jason Wolf

Theses and Dissertations--Manufacturing Systems Engineering

Next generation defense and commercial applications for structural steels require new alloys that eliminate or reduce critical elements from their composition to lower cost and improve manufacturability, while maintaining or exceeding high strength and toughness requirements. A new alloy, denoted as AF9628, has recently been developed for this purpose and its manufacturing characteristics and the material response in component manufacturing must be fully understood.

In the present study, hardened AF9628 alloy was turned with a coated carbide cutting tool under fixed cutting speed, feed rate, and depth of cut parameters. This work focuses on chip-form and tool-wear analysis to understand, …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Designing And Redesigning Products, Processes, And Systems For A Helical Economy, Ryan Bradley, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

The Circular Economy (CE) concept has promised to unlock trillions of dollars in business value while driving a significant reduction in the world’s resource consumption and anthropogenic emissions. However, CE mainly lives in ambiguity in the manufacturing domain because CE does not address the changes needed across all of the fundamental elements of manufacturing: products, processes, and systems. Conceptually, CE is grounded in the concept of closed-loop material flows that fit within ecological limits. This grounding translates into a steady state economy, a result that is not an option for the significant portion of the world living in poverty. Therefore, …

Rotary Friction Welding Versus Fusion Butt Welding Of Plastic Pipes – Feasibility And Energy Perspective, Ramsey F. Hamade, Tarek R. Andari, Ali H. Ammouri, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

According to the Plastics Pipe Institute, butt fusion is the most widely used method for joining lengths of PE pipe and pipe to PE fittings “by heat fusion” (https://plasticpipe.org/pdf/chapter09.pdf). However, butt-welding is not energy-cognizant from the point of view of a phase-change fabrication method. This is because the source of heating is external (heater plate). The initial heating and subsequent maintenance at relatively high temperature (above 200 C for welding of high-density polyethylene pipe) is energy intensive. Rotary friction welding, on the other hand focuses the energy where and when as needed because it uses electric motor to generate mechanical …