Manufacturing Commons^™

Femtosecond Pulse Filamentation In Dielectric Media Toward Photonics Sensor Fabrication, Anitha Narayanan

Theses and Dissertations

Through pulse filamentation, femtosecond laser pulses have been utilized to modify the refractive indices of dielectric materials such as glass, A-plane sapphire crystal, and Cplane sapphire crystal. The 10x Infinity Corrected Lens was used, and the focusing condition was tuned as being the same and fixed to both glass and sapphire crystals. First, 8uJ of laser energy was optimized to produce controlled pulse filamentation voids in the glass. The laser intensity was then optimized to 2-3.5 uJ, 1.5 uJ, & 2.5 uJ, respectively, for the controlled pulse filamentation in A and C plane sapphire crystals. Due to the different crystal …

Design And Fabrication Of Invar Layup Tool Molds Using Additive And Subtractive Manufacturing, Matthew Lamsey

Masters Theses

The development of novel additive manufacturing technologies, such as Wire Arc Additive Manufacturing (WAAM), has opened the door for the fabrication of complex part geometries that could not be achieved with traditional manufacturing methods. Best practices for designing parts for fabrication with WAAM are still in their infancy. This thesis presents a novel design and fabrication framework for parts created using WAAM, which was realized through the fabrication of two demonstration composite layup tool molds. The framework includes design principles for WAAM, finite element simulation of part performance, metrological analysis of printed preforms, and considerations for closely integrating the WAAM …

Design, Fabrication, And Testing Of A High-Speed, Low-Cost Atomic Force Microscope Housing And Distance Measurement System, Jonathan Menke

All Undergraduate Theses and Capstone Projects

Advances to the state-of-the-art in fields like biology and material science often stand on the foundation of improved imaging. Here a low-cost Atomic Force Microscope (AFM) housing and distance measurement system was designed, fabricated, and tested. The instrument was developed around an Optical Pickup Unit (OPU) and designed for use as part of a high-speed AFM system. A structure to align the OPU with the probe holder was designed to ensure the beam of the OPU is positioned above the probe in addition to accommodating space, manufacturability, and cost constraints by using cost effective components. The designs were fabricated and …

Development Of An Anatomically And Electrically Conductive Brain Phantom For Transcranial Magnetic Stimulation, Hamzah A. Magsood

Theses and Dissertations

Transcranial Magnetic Stimulation (TMS) is a non-invasive technique for diagnostics, prognostic, and treatments of various neurological diseases. However, the lack of anatomically realistic brain phantoms has made the experimental verification of stimulation strength in the form of induced electric fields/voltages in the brain tissues an impediment to developing new TMS coils, stimulators, and treatment protocols. There are significant technological, safety, and ethical limitations to test the potential TMS treatment procedures or develop enhancements and refine them on humans or animals. This work aims to bridge the gap by introducing and developing an innovative manufacturing and fabrications process to produce a …

Custom Designed Wall Mounted Shop Crane, Bradley Lewis

All Undergraduate Projects

The objective of this project was to design and fabricate a custom wall mounted jib crane to specific, non-standard dimensions. The crane was designed to be industry rated for 2000 pounds, rotate at least 180 degrees, and be designed to have a maximum boom length tailored to the specific installation site. Two potential installation sites and purposes were selected for construction: inside the bay doors of a fabrication shop, intended to transfer large pieces of material to and from a plasma table, and inside a car maintenance garage, intended to lift and remove engines and transmissions from cars.

Design of …

H.F. Hauff Outrigger: Vertical Arm, Juan Tovar

All Undergraduate Projects

H.F. Hauff is a company based out of Yakima which specializes in farming equipment. One of their products is a trailer which has a wind machine attached to it. In order to keep the fan’s thrust from tipping the trailer over, the trailer needs outriggers to extend out. The outriggers also serve as a way to level out the trailer in uneven surfaces. The outriggers are what needed to be designed. This portion of the project was the vertical arm which extends from the horizontal arm, and goes towards the ground to raise the trailer. The project consisted of three …

Modification Of A Draw Bar Type Arena Harrow To Three Point Mounted Type Harrow, Clayton Alan Brown

BioResource and Agricultural Engineering

This senior project will be the design, and construction of a three point hitch to be attached to a draw bar type spike tooth harrow. Currently used by the Cal Poly Rodeo Team to cultivate their arena before performances, and practices.

The attachment will allow the harrow to be pulled in both directions to create different types of soil affects.

Also the fabrications has a minimal budget so the majority of the materials will be scrap material already in position of the rodeo team or donated to the project.

S&G Metal Fab Battery Tray, Matthew Nartatez

Industrial and Manufacturing Engineering

This report was written for the design of a battery tray and manufacturing process for S&G Metal Fab. The manufacturing steps of how to process the sheet metal to create the product are defined and documented in this report. This project began with constraints given by S&G and were all accomplished using coursework knowledge obtained as a manufacturing engineer student at Cal Poly San Luis Obispo. This report mainly covers parameters regarding the cutting, bending and, deforming of sheet metal to acquire the desired shapes and sizes. It also analyzes the costs that are associated with these processes and material. …