Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 7 of 7
Full-Text Articles in Manufacturing
Rc Baja: Drivetrain And Steering, Mathew Morgan
Rc Baja: Drivetrain And Steering, Mathew Morgan
All Undergraduate Projects
The RC Baja competition is a contest where undergraduate mechanical engineering students design, build, and compete against one another. The objective of this competition is to create the most efficient RC car possible. A gear train analysis was done and showed an 8:1 gear ratio would be the most efficient ratio due to the chosen motor having a higher torque output. Also, a stress analysis was done and showed that 2011 T3 aluminum passed the stress and weight criteria. These analyses ensured the RC Baja car was efficient. Most of the parts for the drivetrain and steering subassemblies were machined …
R/C Baja: Drivetrain, Connor T. Donovan
R/C Baja: Drivetrain, Connor T. Donovan
All Undergraduate Projects
The Central Washington University Mechanical Engineering Technology Department hosts an annual R/C Baja competition in which R/C cars fabricated by student teams are put through a series of courses and tests to determine which team's vehicle is best. The goal of this project was to create a functioning drivetrain that conveys power from the battery to the wheels and provides control of the vehicle. A list of requirements for the drivetrain was created to ensure that the vehicle will not only function, but that it will actually succeed in the competition. These requirements included that the vehicle must achieve a …
Team H&H Rc Baja Drivetrain, William T. Hedlund
Team H&H Rc Baja Drivetrain, William T. Hedlund
All Undergraduate Projects
A need for a drivetrain and steering system that could provide locomotion and directional control for the H&H RC Baja racecar was needed. The RC Baja event is a competition hosted by the CWU ASME club in which teams of engineering students compete against each other to test the effectiveness of the respective designs. The car needed to be able to compete in three events: a drag race, solemn course, and a Baja event. This was accomplished by designing and manufacturing several parts of different materials utilizing a range of manufacturing techniques to produce sub-assemblies and that made up the …
Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero
Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero
All Undergraduate Projects
Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …
R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois
R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois
All Undergraduate Projects
The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …
Carbon Fiber Recycling: Delamination System, Aaron Eastman
Carbon Fiber Recycling: Delamination System, Aaron Eastman
All Undergraduate Projects
The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …
Jcati Carbon Fiber Shredder 2022, Parker Sudderth
Jcati Carbon Fiber Shredder 2022, Parker Sudderth
All Undergraduate Projects
This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …