Manufacturing Commons^™

Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

We review the process rates and energy intensities of various additive processing technologies and focus on recent progress in improving these metrics for laser powder bed fusion processing of metals, and filament and pellet extrusion processing of polymers and composites. Over the last decade, observed progress in raw build rates has been quite substantial, with laser metal processes improving by about 1 order of magnitude, and polymer extrusion processes by more than 2 orders of magnitude. We develop simple heat transfer models that explain these improvements, point to other possible strategies for improvement, and highlight rate limits. We observe a …

Pulsed Laser Beam Welding Of Pd43Cu27Ni10P20 Bulk Metallic Glass, Ling Shao, Amit Datye, Jiankang Huang, Jittisa Ketkaew, Sung Woo Sohn, Shaofan Zhao, Sujun Wu, Yuming Zhang, Udo D. Schwarz, Jan Schroers

Electrical and Computer Engineering Faculty Publications

We used pulsed laser beam welding method to join Pd₄₃Cu₂₇Ni₁₀P₂₀ (at.%) bulk metallic glass and characterized the properties of the joint. Fusion zone and heat-affected zone in the weld joint can be maintained completely amorphous as confirmed by X-ray diffraction and differential scanning calorimetry. No visible defects were observed in the weld joint. Nanoindentation and bend tests were carried out to determine the mechanical properties of the weld joint. Fusion zone and heat-affected zone exhibit very similar elastic moduli and hardness when compared to the base material, and the weld joint shows high …

Maximizing Operating Room Performance Using Portfolio Selection, Vivek Reddy Gunna, Amin Abedini, Wei Li

Mechanical Engineering Faculty Publications

The operating room (OR) is responsible for most hospital admissions and is one of the most cost and work intensive areas in the hospital. From recent trends, we observe an ironic parallel increase among expenditure and waiting time. Therefore, improving OR scheduling has become obligatory, particularly in terms of patient flow and benefit. Most of the hospitals rely on average patient arrivals and processing times in OR planning. But in practice, variations in arrivals and processing times causes high instability in OR performance. Our model of optimization provides OR schedules maximizing patient flow and benefit at a fixed level of …

An Optimization Model For Operating Room Scheduling To Reduce Blocking Across The Perioperative Process, Amin Abedini, Wei Li, Honghan Ye

Mechanical Engineering Faculty Publications

Operating room (OR) scheduling is important. Because of increasing demand for surgical services, hospitals must provide high quality care more efficiently with limited resources. When constructing the OR schedule, it is necessary to consider the availability of downstream resources, such as intensive care unit (ICU) and post anaesthesia care unit (PACU). The unavailability of downstream resources causes blockings between every two consecutive stages. In this paper we address the master surgical schedule (MSS) problem in order to minimize blockings between two consecutive stages. First, we present a blocking minimization (BM) model for the MSS by using integer programming, based on …

Sustainable Manufacturing Performance Evaluation: Integrating Product And Process Metrics For Systems Level Assessment, Aihua Huang, Fazleena Badurdeen

Mechanical Engineering Faculty Publications

This paper builds on the previously developed product sustainability index (ProdSI) and process sustainability index (ProcSI), and presents a framework for sustainable manufacturing performance evaluation at the systems level. The framework is then used to propose a comprehensive set of metrics for the enterprise level following a five-stage metrics hierarchy (individual metrics, sub-clusters, clusters, sub-index and index). The 6R concept (reduce, reuse, recycle, recover, redesign and remanufacture), total life-cycle emphasis, and triple bottom line (TBL) are considered for selecting relevant metrics. Finally, the metrics are integrated to develop an index for enterprise level sustainability assessment and …

Strategies For Value Creation Through Sustainable Manufacturing, Fazleena Badurdeen, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Making the business case and establishing strategic directions for sustainable manufacturing requires a collaborative effort. Strategic capabilities that can help create sustainable value for all stakeholders must be identified. Technologies and methodologies to provide these capabilities for implementation must then be developed, through public-private partnerships. This paper presents major business imperatives and strategic capabilities necessary to enable value creation through sustainable manufacturing identified based on extensive engagement with business leaders and industry professionals as well as academic experts and government agency representatives. The paper also presents a future vision for sustainable products, processes and systems that can be derived from …

Investigation Of Polishing Methods And Surface Analysis After Machining Aisi 4140 Alloy Steel, Qiang Qi

Theses and Dissertations--Mechanical Engineering

AISI 4140 alloy steel has been a very common material to be investigated in automotive and aerospace industries for several decades. AISI 4140 alloy steel is chromium, molybdenum, and manganese containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. The functional performance is largely determined by the surface states after machining.

The aim of the present study is to explore the polishing methods and surface analysis after machining AISI 4140 alloy steel in different cutting speeds and cooling conditions. The surface analysis includes surface roughness, hardness and residual stresses. Compared to traditional …

Adaptive Scheduling For Operating Room Management, Honghan Ye

Theses and Dissertations--Mechanical Engineering

The perioperative process in hospitals can be modelled as a 3-stage no-wait flow shop. The utilization of OR units and the average waiting time of patients are related to makespan and total completion time, respectively. However, minimizations of makespan and total completion time are NP-hard and NP-complete. Consequently, achieving good effectiveness and efficiency is a challenge in no-wait flow shop scheduling. The average idle time (AIT) and current and future idle time (CFI) heuristics are proposed to minimize makespan and total completion time, respectively. To improve effectiveness, current idle times and future idle times are taken into consideration …

Torque Response Of Thin-Film Ferromagnetic Prisms In Uniform Magnetic Fields At Macro And Micro Scales, Soroosh Torabi

Theses and Dissertations--Mechanical Engineering

The non-contact nature of magnetic actuation makes it useful in a variety of microscale applications, from microfluidics and lab-on-a-chip devices to classical MEMS or even microrobotics. Ferromagnetic materials like nickel are particularly attractive, because they can be easily deposited and patterned using traditional lithography-based microscale fabrication methods. However, the response of ferromagnetic materials in a magnetic field can be difficult to predict. When placed in a magnetic field, high magnetization is induced in these ferromagnetic materials, which in turn generates force and/or torque on the ferromagnetic bodies. The magnitude and direction of these forces are highly dependent on the type …

The Limits & Effects Of Draw On Properties And Morphology Of Pan-Based Precursor And The Resultant Carbon Fibers, Sarah Edrington

Theses and Dissertations--Mechanical Engineering

The process, structure, and property relationship of PAN fiber as a precursor to carbon fiber was studied. The limitations of stable spinning and property improvement associated with hot draw in solution spinning were found and quantified. Conditions were varied to generated precursor fiber up to the limit of draw, from which actual samples were collected for thermal conversion to carbon fiber. Samples of PAN and subsequent carbon fiber were characterized using tensile testing and x-ray analysis. The effects of draw on modulus and break stress, as well as the orientation of the crystalline structure of both parent precursor and resultant …

Shape Memory Behavior Of Dense And Porous Niti Alloys Fabricated By Selective Laser Melting, Soheil Saedi

Theses and Dissertations--Mechanical Engineering

Selective Laser Melting (SLM) of Additive Manufacturing is an attractive fabrication method that employs CAD data to selectively melt the metal powder layer by layer via a laser beam and produce a 3D part. This method not only opens a new window in overcoming traditional NiTi fabrication problems but also for producing porous or complex shaped structures. The combination of SLM fabrication advantages with the unique properties of NiTi alloys, such as shape memory effect, superelasticity, high ductility, work output, corrosion, biocompatibility, etc. makes SLM NiTi alloys extremely promising for numerous applications.

The SLM process parameters such as laser power, …

A Framework And Metrics For Sustainable Manufacturing Performance Evaluation At The Production Line, Plant And Enterprise Levels, Aihua Huang

Theses and Dissertations--Mechanical Engineering

Sustainable manufacturing is becoming increasingly important due to scarcity of natural resources, stricter regulations and increasing customer demand for sustainable products. Sustainable manufacturing involves the use of sustainable processes and systems to produce more sustainable products. In order to meet these demands for sustainable products, manufacturing companies have to adopt numerous strategies to achieve sustainable manufacturing. The approach for evaluating sustainable products and processes have been investigated in previous work where product/process sustainability indices were proposed. However, no comprehensive methods are available for sustainable manufacturing performance evaluation at the system level. This work aims to develop two alternate methods for …

Development Of A Supplier Segmentation Method For Increased Resilience And Robustness: A Study Using Agent Based Modeling And Simulation, Adam J. Brown

Theses and Dissertations--Mechanical Engineering

Supply chain management is a complex process requiring the coordination of numerous decisions in the attempt to balance often-conflicting objectives such as quality, cost, and on-time delivery. To meet these and other objectives, a focal company must develop organized systems for establishing and managing its supplier relationships. A reliable, decision-support tool is needed for selecting the best procurement strategy for each supplier, given knowledge of the existing sourcing environment. Supplier segmentation is a well-established and resource-efficient tool used to identify procurement strategies for groups of suppliers with similar characteristics. However, the existing methods of segmentation generally select strategies that optimize …

Product Disassemblability And Remanufacturability Assessment: A Quantitative Approach, Ammar Ali

Theses and Dissertations--Mechanical Engineering

Majority of the products get discarded at end-of-life (EoL), causing environmental pollution, and resulting in a complete loss of all materials and embodied energy. Adopting a closed-loop material flow approach can aid preventing such losses and enable EoL value recovery from these products. Design and engineering decisions made and how products are used impact the capability to implement EOL strategies such as disassembly and remanufacturing. Some underlying factors affecting the capability to implement these EOL strategies have been discussed in previous studies. However, relevant metrics and attributes are not well defined and comprehensive methods to quantitatively evaluate them are lacking. …