Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Additive manufacturing (3)
- Hybrid manufacturing (2)
- Adhesion (1)
- Build plate (1)
- COVID-19 (1)
-
- Composites (1)
- Durability (1)
- Environmental impact (1)
- Face masks (1)
- First Ray Dorsal Mobility (1)
- Foot (1)
- Fused granular fabrication (1)
- Hypermobility (1)
- Instability (1)
- Large area additive manufacturing (1)
- Life cycle analysis (1)
- Medical Device (1)
- Open molding (1)
- Recycling (1)
- Reliability Study (1)
- Surface finish (1)
- Sustainability (1)
- Tooling design (1)
- VARTM (1)
- Vacuum infusion (1)
- Wear (1)
Articles 1 - 6 of 6
Full-Text Articles in Manufacturing
Reliability Study Of A New Electromechanical Device Designed To Measure The Relative Dorsal Mobility Of The First Ray Of The Foot, Philippe Passeraub
Reliability Study Of A New Electromechanical Device Designed To Measure The Relative Dorsal Mobility Of The First Ray Of The Foot, Philippe Passeraub
Faculty Publications
Introduction: A new electromechanical instrument has been developed to measure relative dorsal mobility of the first ray in an objective and reliable way by simulating ground reaction forces during gait. This device equally applies a standardized, electronically controlled, and precise force under the first metatarsal head M1 as well as under the heads of the lesser metatarsals M2 to M5. The relative dorsal mobility between these two bearings is then measured. The purpose of this study is to assess the intra- and inter-examiners reliabilities of the measurements obtained with this device. Methods: The protocol included two examiners and 36 feet …
Trade-Off Characterization Between Social And Environmental Impacts Using Agent-Based Models And Life-Cycle Assessment, Joseph C. Leichty, Christopher S. Mabey, Christopher A. Mattson, John L. Salmon, Jason Weaver
Trade-Off Characterization Between Social And Environmental Impacts Using Agent-Based Models And Life-Cycle Assessment, Joseph C. Leichty, Christopher S. Mabey, Christopher A. Mattson, John L. Salmon, Jason Weaver
Faculty Publications
Meeting the UN’s sustainable development goals requires designers and engineers to solve multi-objective optimization problems involving trade-offs between social, environmental, and economic impacts. This paper presents an approach for designers and engineers to quantify the social and environmental impacts of a product at a population-level and then perform a trade-off analysis between those impacts. In the approach, designers and engineers define the attributes of the product as well as the materials and processes used in the product’s life cycle. Agent-Based Modeling (ABM) tools that have been developed to model the social impacts of products are combined with Life- Cycle Assessment …
Optimizing Build Plate Adhesion Of Polymers In Fused Granule Fabrication Processes, Alex Schroeder, Jason Weaver
Optimizing Build Plate Adhesion Of Polymers In Fused Granule Fabrication Processes, Alex Schroeder, Jason Weaver
Faculty Publications
Perhaps the most crucial element of fused granule fabrication (FGF) is material adhesion; in order to achieve a successful product, the material being printed must adhere to the build plate. For optimal products, the material should only adhere to the build plate until the print is complete, then be easily removable. This paper examines the effects of different build plates, environments, and bonding agents on material adhesion during the FGF process in a CNC mill machine. The force to remove polycarbonate (PC) and polypropylene (PP) from build plates was tested with various bonding agents. Except in one case, the adhesive …
A Comparison Of Layer Deposition And Open Molding Of Petg By Fused Pellet Fabrication In An Additive Manufacturing System, Alex Gibson, Jason Weaver
A Comparison Of Layer Deposition And Open Molding Of Petg By Fused Pellet Fabrication In An Additive Manufacturing System, Alex Gibson, Jason Weaver
Faculty Publications
Additive manufacturing continues to offer new possibilities in both production and economics. The industry has quickly adopted it to rapidly produce parts that would be difficult or cost preventative otherwise. Recent innovation has expanded its capabilities, however there are still significant limitations. Most AM processes are restricted by materials available, in producing large parts, or by not achieving material deposition speeds to make certain products feasible. In addition, tight tolerances for features and surfaces cannot be produced without substantial post processing. High-speed Fused Pellet Fabrication (FPF) in combination with Hybrid Manufacturing (HM) offers expanded capabilities as additive and subtractive process …
Durability Of Vacuum Infusion Tooling Produced From Fused Granular Fabrication Additive Manufacturing, Nathan Northrup, Jason Weaver, Andy R. George
Durability Of Vacuum Infusion Tooling Produced From Fused Granular Fabrication Additive Manufacturing, Nathan Northrup, Jason Weaver, Andy R. George
Faculty Publications
Large area additive manufacturing (LAAM) has the capability to create tooling that is lower cost than conventionally manufactured tooling and still has sufficient properties for many applications. A vacuum infusion mold was printed from fiberglass-ABS and evaluated for wear and suitability for small vacuum infusion runs. The mold was designed to accentuate high wear as a “worst case” scenario. The mold was able to produce 10 parts successfully before any noticeable change occurred to the surface finish. By 14 parts, the surface finish had roughened sufficiently that demolding was difficult and resulted in damage to the part. Profilometry measurements showed …
Closed Loop Recycling Of Low Friction Polymers In Fused Granule Fabrication Additive Manufacturing Processes, Neil Thompson, Jason Weaver
Closed Loop Recycling Of Low Friction Polymers In Fused Granule Fabrication Additive Manufacturing Processes, Neil Thompson, Jason Weaver
Faculty Publications
Plastic waste is a critical worldwide problem that impacts additive manufacturing (AM). Extensive research has explored how plastic waste in AM can be reduced by recycling prints into new filament, with varying success. An alternative to filament-based extrusion is “fused granule fabrication” (FGF), which extrudes from pellets or granules. This method is often used for large area additive manufacturing (LAAM) of polymers. This paper expands upon the knowledge base from previous research on LAAM and examines the extent to which PETG can be recycled and reprinted through the same FGF tool without significant loss to its material properties. The metric …