Manufacturing Commons^™

Handitrike - Recumbent Tricycle, Sean Higginson, Kevin Howie, Vinay Patel

Mechanical Engineering

This report covers the design and construction of the recumbent racing tricycle for Mr. Robert T. Kelly, a disabled veteran. Unfortunately Rob’s right leg is five inches shorter than his left one and therefore is unable to properly operate standard cranks. Our team HandiTrike is composed of Sean Higginson, Kevin Howie, and Vinay Patel and our project requires us to come up with a design that is feasible to complete within the given three quarters, as well as allow Rob to gain full use of his tricycle. Currently Rob ‘s trike uses the standard crank set up found on most …

Solar Turbines Creep Test Fixture, Rene Maciel, Eric Nelson, Chris Ewald

Mechanical Engineering

No abstract provided.

Formula Sae Turbocharger Engine Development, Eric Griess, Kevin Mccutcheon, Matthew Roberts, William Chan

Mechanical Engineering

This project, Formula SAE Turbocharger System Development, was sponsored by the Cal Poly, San Luis Obispo Formula SAE team. The team proposed this project in order to have a powerful yet lightweight engine so they can be extremely competitive at their competition. The baseline output of the single cylinder 450cc engine (2006 Yamaha WR450F) was 46 horsepower and 27 ft-lb of torque. The goal of this project was to increase the output of that engine to 60 horsepower and 35 ft-lb through the use of a turbocharger.

Strider: Manufacturing Processes, Michael Warren-Angelucci

Industrial and Manufacturing Engineering

The goal of the Strider Project is to create a mobility device that can support a person with weakened leg strength and enable them to be supported and maintain a standing position. A prototype of the Strider was created by three Mechanical Engineering students as their senior project. The topic of this senior project was to analyze and create a manufacturing process for the manufacture of the Strider that will be ergonomic and cost effective.

There were many things that needed to be accomplished in order to create the manufacturing process. The first step was to verify that the prototype …

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Process Improvements For Establishing Cmmi Certification At Company Xyz, Megan Farrell

Industrial and Manufacturing Engineering

CMMI stands for Capability Maturity Model Integration and is an enterprise-wide Process-Improvement model that provides a set of best practices that addresses productivity, performance, costs, and stakeholder satisfaction. This improvement model is generally used in computer software companied and not only does it improve their processes, but many contracts will only be awarded with those companies who are CMMI certified, so it is very important for Company XYZ. This goal of this project was to help improve the CMMI efforts at Company XYZ in 4 of the 20 distinct processes areas to attain a CMMI Maturity Level of 3. Improvement …

Design And Manufacture Of Natural Composite Canoe, Derek Baptista

Industrial and Manufacturing Engineering

Abstract

This report looks into the application and feasibility of manufacturing natural composite canoes. The main fabrics that were analyzed are flax, hemp, and jute. These were then compared to carbon fiber and fiberglass to see the difference in mechanical properties. It was found that the natural fibers have lower mechanical properties but that this could be overcome by designing a balsa wood core with ribs running up the walls. After manufacturing a hemp canoe, many lesson were learned and areas of interest were further explored. With the use of different natural fibers, these canoes can greatly reduce the carbon …

Chsr Clothing: How To Start A Small Business Clothing Line To Be Run Efficiently With Minimum Capital And Maximum Profit, Kayvon Banisalam

Industrial and Manufacturing Engineering

Executive Summary

Many clothing brands have failed because they did not design marketable products with a suitable business plan. Often times, clothing brand owners do not use the capital they possess in efficient ways. They can get caught off guard with unexpected costs and are not running the business in the most resourceful and professional way.

The goal of this project is to create a clothing brand that portrays distinctive designs to go along with an effective business model. This includes implementing decision analysis at several points of the planning phase, along with quality and cost controls. Creating quality products …

Facilities Planning For An Aerospace Manufacturing Company, William Petrossi

Industrial and Manufacturing Engineering

Absolute Technologies Inc. (ATI) has been growing for years, and is running out of space at their current manufacturing facility in Yorba Linda, CA. ATI will be moving to a much larger facility this winter. They are looking for an efficient way to utilize this space. The machine positions were taken as fixed, seeing as a lean expert was brought in to give advice on placement. With the machines fixed, the scope was narrowed to other areas.

A systematic approach to facilities design is utilized. First, a goal needs to be defined. The goal is to reduce the time wasted …

Consolidation Of Company Abc, Estelle Sillari-Owen

Industrial and Manufacturing Engineering

This project aims to solve Company ABC’s issues in order to keep the company afloat and to keep the company profitable. This was done by reducing Company ABC’s organizational and inventory build-up issues. The project aims to reduce the company’s dependence on outside storage, with plans of consistent inventory reduction over the next year. An implementation plan was created to ensure the company keeps on track to increase profits and prevent against increasing inventory costs.

Work In Progress: Outreach Assessment: Measuring Engagement, Lizabeth Schlemer, John Oliver, Katherine Chen, Sophia Rodriguez Mata, Eric Kim

Industrial and Manufacturing Engineering

The Learn By Doing Lab (LBDL) at Cal Poly, San Luis Obispo is an on-campus laboratory where 5th through 8th grade students are taught by undergraduates who may be planning a careers in teaching. The two populations - elementary students and undergraduates - are equally important in the process. Since 2008, the lab has seen over 4000 elementary and junior high students and over 100 undergrads have participated. In most outreach assessment the number of individuals participating is an important metric, but this last Spring we experimented with a more in depth measure of effectiveness. As in any learning experience …

Warehouse Redesign, Cristine Carmel Dewar

Industrial and Manufacturing Engineering

A young, growing biomedical company is expanding its warehouse space to keep up with the increasing production. This project’s goals were to recommend a layout and improve a process that would minimize the distance traveled by the material handlers, increase the safety of the warehouse by implementing visual controls, implement ergonomics to reduce chance of injury, and save money for the company. To achieve this first I familiarized myself with their current processes and department and the space required for their current and future production levels. Next I created two alternative layouts, the first (Layout A) to minimize distance and …

Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd

STAR Program Research Presentations

Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …

Design, Construction, And Evaluation Of An Automated Chicken Coop Door, Kyle Inks

BioResource and Agricultural Engineering

This senior project takes a look into the design, construction, and evaluation of an automated chicken coop door. The idea and need for such a door came from my mother Jan Inks. The parameters for the project include, low production cost, easy installation on existing coops, sleek design, automatically open at a set time in the morning, and automatically close at a set time in the evening.

Design Of An Independent Star-Clip Organizer (Iso), Christopher Gonzales, Greg Lovasik, Daniel Silveira

Mechanical Engineering

Discussed below is a new concept to sort and deliver star clips for flight deck safety net manufacturing. Multiple methods were generated, along with the necessary research, and were narrowed down to a single concept: the tray-loading preprocess design, named ISO (Independent Star-Clip Organizer). The overall design has been finalized and designed. Due to budget constraints, an actual prototype was not built. However, the design of such a prototype is described by this report, backed with calculations and experimental testing.

The Hovering Ball Exhibit, Matthew Bauzon, Will Lennox, Michelle Swan

Mechanical Engineering

No abstract provided.

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Recreational Nordic Sit Ski, Mathew Bissonnette, Johnathon Gorski, Kevin Izumiya

Mechanical Engineering

The purpose of this project was to design, build, and test a recreational Nordic sit ski for use by Disabled Sports Eastern Sierra. The goal was to improve adjustability and reduce weight compared to previous sit ski designs. The project was completed by Cal Poly Mechanical Engineering seniors Mathew Bissonnette, Johnathon Gorski, and Kevin Izumiya. Kinesiology seniors Harpreet Saini and Carl Anderson provided discipline support and disability etiquette training.

The project was sponsored by the National Science Foundation Research to Aid Persons with Disabilities (RAPD) grant. The grant was proposed by and awarded to Dr. Brian Self and Dr. James …

Formula Hybrid Drivetrain Design, Zachary (Zak) Mcfarland, Alex Pruitt, William Domhart

Mechanical Engineering

The Formula Hybrid senior project group was tasked with designing and building a drivetrain system for the Cal Poly Society of Automotive Engineers (SAE) Formula Hybrid (FHSAE) team. FHSAE gave customer requirements for performance and geometry for the drivetrain and the FHSAE rulebook has guidelines regarding safety requirements. The team chose to compete in the electric category of the 2012 FHSAE competition. After getting feedback from previous car performance and researching different powertrain options, the senior project team arrived at three conceptual ideas. Using a quality function deployment method, the senior project team chose the concept where two motors independently …

Integrating Courses Through Project Based Learning, Lizabeth Schlemer, Sema E. Alptekin, Karen R. Bangs

Industrial and Manufacturing Engineering

Integrating three courses (one sophomore level, two senior level) through Project Based Learning (PBL) within the Industrial Engineering curriculum at the California Polytechnic State University, San Luis Obispo is presented. Three courses (IME 443 Facilities Planning and Design - senior level; IME 420 Simulation - senior level; and IME 223 Process Improvement Fundamentals - sophomore level) were linked by various mechanisms: Common industry projects, common students in two of the three courses; senior students having access to sophomores in their teams to carry out time consuming tasks such as time studies, and sophomores having access to seniors as team members, …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Effect Of Gold Content On The Microstructural Evolution Of Sac305 Solder Joints Under Isothermal Aging, Mike Powers, Jianbiao Pan, Julie Silk, Patrick Hyland

Industrial and Manufacturing Engineering

Au over Ni on Cu is a widely used printed circuit board (PCB) surface finish, under bump metallization (UBM), and component lead metallization. It is generally accepted that less than 3 wt.% Au in Sn-Pb solder joints inhibits formation of detrimental intermetallic compounds (IMC). However, the critical limit for Au content in Pb-free solder joints is not well established. Three surface-mount package platforms, one with a matte Sn surface finish and the others with Ni/Au finish, were soldered to Ni/Au-finished PCB using Sn-3.0Ag- 0.5Cu (SAC305) solder, in a realistic manufacturing setting. The assembled boards were divided into three groups: one …

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

The Morphology Evolution And Voiding Of Solder Joints On Qfn Central Pads With A Ni/Au Finish, Julie Silk, Jianbiao Pan, Mike Powers

Industrial and Manufacturing Engineering

In this paper, we report on a comprehensive study regarding the morphology evolution and voiding of SnAgCu solder joints on the central pad of two different packages – QFN and an Agilent package called TOPS – on PCBs with a Ni/Au surface finish. Samples were isothermally aged at the equivalent of 0, 2, 7 and 14 years service life. Representative solder joints were cross-sectioned and analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) in order to investigate the evolution of the solder joint morphology as a function of Au content and isothermal aging. IMC thickness was …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …